驻波声场中单分散细颗粒的相互作用特性

利用外加声场促进悬浮在气相中的细颗粒发生相互作用,进而引起颗粒的碰撞和凝并,使得颗粒平均粒径增大、数目浓度降低,是控制细颗粒排放的重要技术途径.为探究驻波声场中单分散细颗粒的相互作用,建立包含曳力、重力、声尾流效应的颗粒相互作用模型,采用四阶经典龙格-库塔算法和二阶隐式亚当斯插值算法对模型进行求解.将数值模拟得到的颗粒声波夹带速度和相互作用过程与相应的解析解和实验结果进行对比,验证模型的准确性.进而研究颗粒初始条件和直径对相互作用特性的影响.结果表明,初始时刻颗粒中心连线越接近声波波动方向、颗粒位置越接近波腹点,颗粒间的声尾流效应就越强,颗粒发生碰撞所需要的时间就越短.研究还发现,颗粒直径对颗粒相互作用的影响取决于初始时刻颗粒中心连线偏离声波波动方向的程度.当偏离较小时,颗粒直径越大,颗粒发生碰撞所需要的时间越短;当偏离很大时,直径较小的颗粒能够发生碰撞,而直径较大的颗粒则无法发生碰撞.     

A genetic resampling particle filter for freeway traffic-state estimation

On-line estimation of the state of traffic based on data sampled by electronic detectors is important for intelligent traffic management and control.Because a nonlinear feature exists in the traffic state,and because particle filters have good characteristics when it comes to solving the nonlinear problem,a genetic resampling particle filter is proposed to estimate the state of freeway traffic.In this paper,a freeway section of the northern third ring road in the city of Beijing in China is considered as the experimental object.By analysing the traffic-state characteristics of the freeway,the traffic is modeled based on the second-order validated macroscopic traffic flow model.In order to solve the particle degeneration issue in the performance of the particle filter,a genetic mechanism is introduced into the resampling process.The realization of a genetic particle filter for freeway traffic-state estimation is discussed in detail,and the filter estimation performance is validated and evaluated by the achieved experimental data.     

Macrodefect-Free Materials: Modification of Interfaces in Cement Composites by Polymer Grafting

MDF materials are chemically bonded ceramic materials free of the macrodefects typical of hydraulic cement-based materials. MDF materials arising through reactions of sulfo-aluminate-ferrite belitic (SAFB) clinkers and/or Portland cements (PC) with two types of water-soluble polymer (hydroxy-propylmethyl cellulose {HPMC}, polyphosphate glass {poly-P}) are discussed. Mixes of low energy SAFB clinkers with Portland cement, HPMC and, especially poly-P comprise promising cross-linked compositions additional to the better known MDF materials formed from high alumina cement with polyvinylalcohol/acetate. The principles of co-ordination of P and C atoms (of the polymer) with Al and Fe atoms (originating from the cement) are highlighted from spectroscopic information on next-nearest-neighbour interactions, along with the effects of second co-ordination spheres. Polymers modify the interface through functional bonding/grafting of polymer chains onto the surfaces of cement grains. Both the cross-linked atomic structure and the interface coincide well with the model of functional polymers and represent a new type of atomic-level structure in polymer-modified cements. Interpretation is based on previous magnetic resonance and thermal analysis studies. The compactness of Al(Fe)-O-P cross-links reduces transport through the interfaces, increasing the interfacial interactions and resisting the unfavourable uptake of moisture and carbonation.     

Cosmological Particle Creation and Dynamical Casimir Effect

We compute particle creation for a real massive scalar field conformally coupled to a spatially closed Robertson–Walker space-time background, with time-dependent scale factor. This is a dynamical Casimir effect with moving boundaries.     

The response of thermally and optically stimulated luminescence from Al2O3:C to high-energy heavy charged particles

The thermoluminescence (TL) and optically stimulated luminescence (OSL) response of Al₂O₃ dosimeters to high-energy heavy charged particles (HCP) has been studied using the heavy ion medical accelarator at Chiba, Japan. The samples were Al₂O₃ single-crystal chips, of the type usually known as TLD-500, and Luxel^TM dosimeters (Al₂O₃:C powder in plastic) from Landauer Inc. The samples were exposed to ⁴He (150 MeV/u), ¹²C (400 MeV/u), ²⁸Si (490 MeV/u) and ⁵⁶Fe (500 MeV/u) ions, with linear energy transfer values covering the range from 2.26 to 189 keV/μm in water and doses from 1 to 100 mGy (to water). A ⁹⁰Sr/⁹⁰Y beta source, calibrated against a ⁶⁰Co secondary standard, was used for calibration purposes. For OSL, we used both continuous-wave OSL measurements (CW-OSL, using green light stimulation at 525 nm) and pulsed OSL measurements (POSL, using 532 nm stimulation from a Nd:YAG Q-switched laser). The efficiencies (η_HCP,γ) of the different HCPs at producing OSL or TL were observed to depend not only upon the linear energy transfer (LET) of the HCP, but also upon the sample type (single crystal chip or Luxel^TM) and the luminescence method used to define the signal—i.e. TL, CW-OSL initial intensity, CW-OSL total area, or POSL. Observed changes in shape of the decay curve lead to potential methods for extracting LET information of unknown radiation fields. A discussion of the results is given, including the potential use of OSL from Al₂O₃ in the areas of space radiation dosimetry and radiation oncology.     

Measurement of Inherent Material Density of Nanoparticle Agglomerates

We describe a new technique to measure the size dependent inherent material density of chain agglomerate particles. Measurements were carried out for diesel soot and aluminum/alumina agglomerate particles in the nanometer size range. Transmission electron microscopy was used to measure the volumes of agglomerate particles that were preselected by mass using an aerosol particle mass analyzer. We found that the density of diesel exhaust particles increased from 1.27 to 1.78g/cm³ as particle mobility size increased from 50 to 220nm. When particles are preheated to remove volatile components, the density was 1.77±0.07g/cm³, independent of particle size. The densities measured after heating correspond to the inherent material density of diesel soot. Measurements with aluminum nanoparticles were made downstream of a furnace where aluminum (Al) was converted to alumina (Al₂O₃). From measurements of inherent material density we were able to infer the extent of reaction, which varied with furnace temperature.     

Fabrication of copper oxide nanofluid using submerged arc nanoparticle synthesis system (SANSS)

The optimal parameters are found for preparing nanofluid in our submerged arc nanoparticle synthesis system (SANSS) using a copper electrode. A suspended copper oxide nanofluid is thus produced at the current of 8.5–10 A, voltage of 220 V, pulse duration of 12 μs, and dielectric liquid temperature of 2°C. The CuO nanoparticle are characterized by transmission electron microscopy (TEM), field emission scanning electron microscope (FESEM), X-ray diffraction (XRD), electron diffraction pattern (SAD) and electron spectroscopy for chemical analysis (ESCA). The equality volume spherical diameter of the obtained copper oxide particle is 49.1 nm, regular shape and narrow size distribution.This revised version was published online in August 2005 with a corrected issue number.     

What’s Wrong with Einstein’s 1927 Hidden-Variable Interpretation of Quantum Mechanics?

Einsteins unpublished 1927 deterministic trajectory interpretation of quantum mechanics is critically examined, in particular with regard to the reason given by Einstein for rejecting his theory. It is shown that the aspect Einstein found objectionable—the mutual dependence of the motions of particles when the (many-body) wavefunction factorises—is a generic attribute of his theory but that this feature may be removed by modifying Einsteins method in either of two ways: using a suggestion of Grommer or, in a physically important special case, using a simpler technique. It is emphasized though that the presence or absence of the interdependence property does not determine the acceptability of a trajectory theory. It is shown that there are other grounds for rejecting Einsteins theory (and the two modified theories), to do with its domain of applicability and compatibility with empirical predictions. That Einsteins reason for rejection is not a priori grounds for discarding a trajectory theory is demonstrated by reference to an alternative deterministic trajectory theory that displays similar particle interdependence yet is compatible with quantum predictions.PACS: 03.65.Bz.Essay written in memory of J.T. Cushing.     

脉冲激光烧蚀碲镉汞材料的等离子体发射谱

脉冲激光辐照处于不同背景气压下的Hg0.8Cd0.2Te材料表面,用时间和空间分辨诊断技术探测了激光照射后产生的等离子体发射谱,根据所获得的飞行时间谱测量了等离子体中粒子的出射速度,结果表明粒子速度随着出射距离的增加迅速减小,且背景气压对出射速度有很大的影响,而激光能量对粒子速度的影响不大。另外根据谱线的展宽计算了等离子体中的电子密度,结果表明,电子密度在激光辐照样品后的短时间内迅速减小,且电子密度最大的位置不是出现在靶的表面而是在距表面一定距离处。     

Influence of sintering temperature and pH on the phase transformation,particle size and anti-reflective properties of RHA nano silica powders

Nano silica powders were synthesized from rice husk ash, the most silica-rich raw material, using alkaline extraction followed by acid precipitation. The phase transformation during sintering, the influence of sintering temperature and pH on the particle size and anti-reflective properties of nano silica were investigated. The results showed that the amorphous SiO₂ sintered at 600°C were transformed to a cristobalite structures completely during the sintering process at 800°C and 1100°C. With the increasing sintering temperature and pH, the particle size distributions (d₅₀) were increased respectively in the range of 62–84, 192–240, and 283–329?nm at sintering temperatures of 600°C, 800°C, and 1100°C. When the sintering temperatures were increased at 1100°C, 98.15% and 96.84% of transmittances were obtained respectively at the highest and lowest points of the anti-reflection band and could be used for anti-reflective applications.