Synthesis of polypiperazine-amide thin-film membrane on PPESK hollow fiber UF membrane

A new interfacial polymerization (IP) procedure is developed in order to synthesize polypiperazine-amide thin-film membrane on the inner surface of poly(phthalazinone ether sulfone ketone) (PPESK) hollow fiber ultrafiltration (UF) membrane.A hollow fiber composite membrane with good performance was prepared and studied by FT-IR and scanning electron microscopy.     

Suppression of red cell diffusional water permeability by lipophilic solutes

The inhibitory effect of a series of neutral lipophilic solutes (methanol, ethanol, n-propanol, iso-propanol, n-butanol, iso-amylalcohol, n-hexanol, diethylether, nitrobenzene, and pyridine) on the diffusional water permeability (Pd, tot) of bovine erythrocyte membrane at 25 degrees C was studied in comparison to that of p-chloromercuri benzoate (pCMB). Permeability data were obtained by measuring the transmembrane diffusional water exchange time tau(exch) using an 1H-T2 NMR technique. Maximal inhibition by approximately 50% of Pd, tot was produced by 2 mM pCMB which completely blocked the membrane water channels in 20 min, hence suggesting the channel-to-lipid diffusional water permeability ratio of about 1:1. Furthermore, the maximal inhibitory effect of pCMB in combination with the lipophilic solutes was lower than that of pCMB alone. As pCMB does not interfere with the lipid bilayer, and provided that it blocks the water channels in solute presence as well, this confirms that the solutes induce an increase in the lipid-mediated background water permeability contribution (Pd, lipid) by the formation of aqueous leaks in the membrane hydrophobic barrier. However, faster but less efficient in permeability inhibition than pCMB (either alone or combined with solutes) were the lipophilic solutes alone. Taken together, the results indicate that the lipophilic solutes suppress the membrane total permeability Pd, tot by two opposing effects: a reduction of its channel-mediated part (Pd, channel) to the extent exceeding that of a simultaneous Pd, lipid increase. The inhibitory potency of the solutes tested appears to be correlated with their solubility in the membrane medium.     

SYNTHESIS, CROSSLINKING MECHANISM AND PROPERTIES OF A POLYACRYLATE/POLYURETHANE COMPOSITE COATING

A polyacrylate/polyurethane (P(A) / P(U)) composite coating has been prepared bycrosslinking an acetoacetylated polyacrylate with a vinylic group terminated polyurethaneat room temperature. A model Michael reaction between ethyl acetoacetate (EAA) andmethyl acrylate (MA) was designed to study the crosslinking mechanism. It was foundthat the two active hydrogen atoms in acetoacetyl group can both add to vinylic groupsand the yield of mono- and bis-adducts are much affected by the molar ratio of acetoacetylto vinylic groups. Higher crosslinking degree and better properties could be obtained withdecreasing the molar ratio of the two active groups from 1/1 to 0.6/1 in the compositecoatings.     

复合生物材料的研究进展

从力学性能的改善和降解速率的可调度等角度,总结了复合生物材料与单一组分的材料相比,在生物医学领域应用中所表现出的综合使用性能的优越性。综述了复合生物材料,特别是用于骨修复的各类有机／无机复合材料近年来的研究进展状况。提出将与人骨中磷灰石微晶类似的羟基磷灰石纳米粒子与可降解聚酯材料进行复合,能够得到具有优越骨诱导性能并且能够降解的新型骨修复材料。这方面的研究代表了有机／无机复合生物材料领域新的发展方向。     

LLDPE/纳米SiO_2复合材料的力学性能和光学性能研究

采用熔融共混方法制备了LLDPE 纳米SiO2 复合材料 ,并对该体系的力学性能和光学性能进行了系统研究 .结果表明 ,随着纳米SiO2 的加入 ,复合材料的弹性模量显著提高 ,冲击强度与拉伸强度呈峰形变化 ,且均在SiO2 含量为 3phr左右达到最大值 .加入少量的纳米SiO2 后 ,复合材料薄膜对长波红外线 (7～ 1 1 μm)的吸收能力较LLDPE膜有了显著提高 ,透光率略有下降但雾度提高 ,透光质量得到改善 .同时表明 ,纳米SiO2 的表面处理方法对膜的光学性能有显著影响     

Sol-gel polyimide-silica composite membrane: gas transport properties

The effect of introduction of silica particles prepared by the sol-gel technique on the gas transport properties of a polyimide film was studied. The sorption and permeation of N₂, O₂, CO₂, H₂ and CH₄ were studied and correlated with morphological changes in the polymer structure. From sorption isotherms, we observed that the composite membrane presents higher solubility coefficients than the polyimide one. The solubility coefficient ratio between the composite and the polyimide is about 1.5–2.0. The isotherms were analyzed in terms of the dual mode sorption. The Henry's coefficient and the Langmuir's affinity and saturation constants were obtained allowing to calculate the Langmuir to Henry concentration ratios as function of the gas pressure. These ratios decrease until zero within a certain pressure range as long as the Langmuir's mode is acting and they are higher for the polyimide membrane when compared with the composite one. This study was completed with calorimetric measurements during the sorption. The gas interaction energy in kJ/mol decreases within the same pressure range as previously described. The measured energies are higher for the polyimide film when compared with the composite one because the polyimide membrane presents a stronger energetic effect caused by a higher Langmuir's contribution. From permeation studies at 3.15⁵ Pa, the composite membrane showed higher permeability coefficients and permselectivities than the polyimide one. All these results were explained, taking into account the difference on the imidization degree of both membranes and the morphological changes which may be induced by the silica nodules in the organic/inorganic interphases.     

互通多孔碳/二氧化锰纳米复合材料的原位水热合成及电化学性能

以互通多孔碳（IPC）为载体，水热条件下在碳表面原位反应生成纳米结构的二氧化锰（MnO₂），制备互通多孔碳/二氧化锰纳米（IPC/MnO₂）复合电极材料. 采用扫描电镜（SEM），透射电镜（TEM），X射线衍射（XRD），热重分析（TGA）对其结构进行表征；采用循环伏安法、恒流充放电和交流阻抗对其电化学性能进行研究. 结果表明：生成的MnO₂均匀地负载在碳的表面，形成多层次结构，并且随着温度的升高IPC表面负载的MnO₂由纳米颗粒变为纳米片状结构；MnO₂纳米片具有典型的K-Birnessite 型晶体结构；复合物中MnO₂的含量约为34%（w）. 在100 ℃制备的IPC/MnO₂复合材料在三电极系统中最高比电容达到了411 F·g^-1；随着反应温度的升高,比容量先增长后基本保持不变. 以IPC/MnO₂为正极，活性炭（AC）为负极，1 mol·L^-1 Na₂SO₄溶液为电解液组装成IPC/MnO₂//AC 混合超级电容器，发现IPC/MnO₂电极的电容器其电位窗口从1 V扩展到1.8 V，容量可达86F·g^-1，且表现出良好的电容特性和大电流放电性能.     

安培检测芯片毛细管电泳及其初步应用

An end-channel amperometric detector with a guide tube for working electrode was designed and integrated on a home-made glass microchip. The guide tube was directly patterned and fabricated at the end of the detection reservoir, which made the fixation and alignment of working electrode relatively easy. The fabrication was carried out in a two-step etching process. A 30 μm carbon fiber microdisk electrode and Pt cathode were also integrated onto the amperometric detector. The baseline separation of dopamine (DA), catechol (CA) and epinephrine (EP) was achieved within 80 s. Relative standard deviations of not more than 5.2% were obtained for both peak currents and migration times of DA and CA (n=5). Using standard adding method, DA in tLrine and plasma samples was detected. The recoveries were in the range of 83%—103%.     

Determination of degree of conversion as a function of depth of a photo-initiated dental restoration composite—III application to commercial Prodigy Condensable™

In this third work, we evaluated the degree of conversion (DC) versus depth of dental filling composite named Prodigy Condensable™ using infrared spectroscopy. Confirming previous results, there was a gradual reduction of DC with increasing depth but the composite exhibited extreme values of DC, an upper value (45.9%) on the surface and a lower one (6.1%) at a depth of 5 mm. The composite presented the worst performance among materials studied. The composite formulation was 80% of inorganic fillers and BisfenolA/dimethacrylate (BisGMA) (18%)/triethyleneglycoldimethacrylate (TEGDMA) (2.0%) as monomers. As stated before, type/ratio/viscosity of monomers and type, amount, size and size distribution of fillers all together had an important role in the cure reaction contributing to the final performance of the composite.