Preparation and characterization of Ti0.7Sn0.3O2 as catalyst support for oxygen reduction reaction

Sn-doped TiO_2 nanoparticles with high surface area of 125.7 m~2·g~(-1) are synthesized via a simple one-step hydrothermai method and explored as the cathode catalyst support for proton exchange membrane fuel cells.The synthesized support materials are studied by X-ray diffraction analysis,energy dispersive X-ray spectroscopy and transmission electron microscopy.It is found that the conductivity has been greatly improved by the addition of 30 mol%Sn and Pt nanoparticles are well dispersed on Ti_(0.7)Sn_(0.3)O_2 support with an average size of 2.44 run.Electrochemical studies show that the Ti_(0.7)Sn_(0.3)O_2 nanoparticles have excellent electrochemical stability under a high potential compared to Vulcan XC-72.The as-synthesized Pt/Ti_(0.7)Sn_(0.3)O_2 exhibits high and stable electrocatalytic activity for the oxygen reduction reaction.The Pt/Ti_(0.7)Sn_(0.3)O_2 catalyst reserves most of its electrochemically active surface area(ECA),and its half wave potential difference is 11 mV,which is lower than that of Pt/XC-72(36 mV) under 10 h potential hold at 1.4 V vs.NHE.In addition,the ECA degradation of Pt/Ti_(0.7)Sn_(0.3)O_2is 1.9 times lower than commercial Pt/XC-72 under 500 potential cycles between 0.6 V and 1.2 V vs.NHE.Therefore,the as synthesized Pt/Ti_(0.7)Sn_(0.3)O_2 can be considered as a promising alternative cathode,catalyst for proton exchange membrane fuel cells.     

纤维素纳米晶体薄膜的制备与表征

讨论了两种新型纤维素纳米晶体(Cellulose nanocrystal,CNC)薄膜的制备方法:浸没法和旋涂法,并利用红外反射吸收光谱(Infrared reflection absorption spectroscopy,IRRAS)和原子力显微镜(Atomic force microscopy,AFM)对其进行表征。AFM高度图显示两种工艺制备的CNC薄膜均由棒状的CNC纳米颗粒交错叠加而成。实验结果显示,旋涂法制备的薄膜更加光滑,粗糙度RMS约为2.7 nm。由于带电颗粒间斥力的存在,浸没法制备的CNC膜厚度最大约为15 nm,而旋涂法可以得到更厚的CNC薄膜,其厚度可达50 nm以上。研究CNC悬浮液浓度与旋涂法CNC膜厚之间的关系后发现,可以通过改变CNC溶液的浓度对薄膜厚度进行控制。IRRAS结果也证实随着CNC悬浮液浓度的增加,旋涂薄膜的厚度随之增加。     

铅镉重金属离子在铋膜电极上的相互影响

采用原位镀铋电极的方式,以玻碳电极为工作电极,通过改变Cd2+和Pb2+的比例,考察不同Pb2+和Cd2+浓度条件下,两者同时存在时的相互影响。实验发现,Cd2+和Pb2+同时存在时,存在相互的影响,特别是对于Cd2+的检测,由于Pb2+较正的析出电位,对于Cd2+的析出有一定的辅助作用。考察了Cd2+和Pb2+单独存在时的分析性能,Pb2+沉积时间为60 s时,在1~80μg/L范围内呈线性关系,检出限为0.5μg/L;Cd2+的沉积时间为120 s,在1~25μg/L和30~200μg/L范围内有良好的线性关系,检出限为1.0μg/L。考察了铋膜电极在不同实际水样中对Pb2+和Cd2+的分析,获得了较好的一致性。     

丝网印刷法制备高催化活性对电极

对电极在染料敏化太阳能电池（DSCs）中主要起催化氧化还原反应及收集电荷的作用,铂对电极常用的制备方法为磁控溅射法,但其成本较高,制备条件苛刻. 本文通过引入低成本的表面活性剂Span-85,所制得的铂对电极的附着力、透光率和均匀性显著改善,实现了面积可控,与两步浸泡法和旋涂热解法制备的对电极在DSCs中的光电转换效率分别为7.30%,6.96%和7.03%. 紫外-可见吸收光谱、扫描电镜和附着力测试等结果表明,（1）添加表面活性剂有利于增加附着力及改善透光率和均匀性;（2）使用该法制备的Pt/FTO对电极的透光率与两步浸泡法制作的相同,且铂粒子分布更加均匀. 电化学阻抗图谱、塔菲尔极化曲线和循环伏安曲线结果表明,丝网印刷方法制备的Pt/FTO对电极具有更加优异的催化性能,且该法更有利于降低其生产成本和大规模生产.     

A Non-Conjugated Polymer Acceptor for Efficient and Thermally Stable All-Polymer Solar Cells

A non-conjugated polymer acceptor PF1-TS4 was firstly synthesized by embedding a thioalkyl segment in the mainchain, which shows excellent photophysical properties on par with a fully conjugated polymer, with a low optical band gap of 1.58 eV and a high absorption coefficient >10⁵ cm⁻¹, a high LUMO level of −3.89 eV, and suitable crystallinity. Matched with the polymer donor PM6, the PF1-TS4-based all-PSC achieved a power conversion efficiency (PCE) of 8.63 %, which is ≈45 % higher than that of a device based on the small molecule acceptor counterpart IDIC16. Moreover, the PF1-TS4-based all-PSC has good thermal stability with ≈70 % of its initial PCE retained after being stored at 85 °C for 180 h, while the IDIC16-based device only retained ≈50 % of its initial PCE when stored at 85 °C for only 18 h. Our work provides a new strategy to develop efficient polymer acceptor materials by linkage of conjugated units with non-conjugated thioalkyl segments.     

Facile Preparation of WO3−x Dots with Remarkably Low Toxicity and Uncompromised Activity as Co-reactants for Clinical Diagnosis by Electrochemiluminescence

The exceptional nature of WO_3−x dots has inspired widespread interest, but it is still a significant challenge to synthesize high-quality WO_3−x dots without using unstable reactants, expensive equipment, and complex synthetic processes. Herein, the synthesis of ligand-free WO_3−x dots is reported that are highly dispersible and rich in oxygen vacancies by a simple but straightforward exfoliation of bulk WS₂ and a mild follow-up chemical conversion. Surprisingly, the WO_3−x dots emerged as co-reactants for the electrochemiluminescence (ECL) of Ru(bpy)₃²⁺ with a comparable ECL efficiency to the well-known Ru(bpy)₃²⁺/tripropylamine (TPrA) system. Moreover, compared to TPrA, whose toxicity remains a critical issue of concern, the WO_3−x dots were ca. 300-fold less toxic. The potency of WO_3−x dots was further explored in the detection of circulating tumor cells (CTCs) with the most competitive limit of detection so far.     

Interfacial Strain Release from the WS2/CsPbBr3 van der Waals Heterostructure for 1.7 V Voltage All-Inorganic Perovskite Solar Cells

Perovskite lattice distortion induced by residual tensile strain from the thermal expansion mismatch between the electron-transporting layer (ETL) and perovskite film causes a sluggish charge extraction and transfer dynamics in all-inorganic CsPbBr₃ perovskite solar cells (PSCs) because of their higher crystallization temperatures and thermal expansion coefficients. Herein, the interfacial strain is released by fabricating a WS₂/CsPbBr₃ van der Waals heterostructure owing to their matched crystal lattice structure and the atomically smooth dangling bond-free surface to act as a lubricant between ETL and CsPbBr₃ perovskite. Arising from the strain-released interface and condensed perovskite lattice, the best device achieves an efficiency of 10.65 % with an ultrahigh open-circuit voltage of 1.70 V and significantly improved stability under persistent light irradiation and humidity (80 %) attack over 120 days.     

A Fully Non-fused Ring Acceptor with Planar Backbone and Near-IR Absorption for High Performance Polymer Solar Cells

Fused-ring electron acceptors have made significant progress in recent years, while the development of fully non-fused ring acceptors has been unsatisfactory. Here, two fully non-fused ring acceptors, o-4TBC-2F and m-4TBC-2F, were designed and synthesized. By regulating the location of the hexyloxy chains, o-4TBC-2F formed planar backbones, while m-4TBC-2F displayed a twisted backbone. Additionally, the o-4TBC-2F film showed a markedly red-shifted absorption after thermal annealing, which indicated the formation of J-aggregates. For fabrication of organic solar cells (OSCs), PBDB-T was used as a donor and blended with the two acceptors. The o-4TBC-2F-based blend films displayed higher charge mobilities, lower energy loss and a higher power conversion efficiency (PCE). The optimized devices based on o-4TBC-2F gave a PCE of 10.26 %, which was much higher than those based on m-4TBC-2F at 2.63 %, and it is one of the highest reported PCE values for fully non-fused ring electron acceptors.     

Estimation of band alignment at CdS/Cu2ZnSnS4 hetero-interface by direct XPS measurements

This paper aims to estimate the band alignment to CdS/CZTS hetero-interface by direct X-ray photoelectron spectroscopy (XPS) measurements. XPS was used to determinate the valence-band offset (VBO) directly by determining the valence band positions at the hetero-interface. The conduction band offset (CBO) value was estimated based on the band gap measurements by UV/Visible spectroscopy and VBO measurements. The position of valence band (VB) changes close to the CdS-CZTS interface and the CBO is cliff-like. The band alignment diagram indicates that the CdS-CZTS interface heterojunction is type II.