Structure and properties of the mesophase of syndiotactic polystyrene. VIII. Solvent sorption behavior of syndiotactic polystyrene/p‐chlorotoluene mesophase membranes

A crystalline δ form of a syndiotactic polystyrene (sPS) membrane was prepared from a solution of sPS (1 wt %) and p‐chlorotoluene (p‐CT) by a solution‐casting method. The mesophase (δ empty form) of sPS was obtained by the extraction of the guest solvent from the δ form of sPS by a stepwise solvent‐extraction method. The sPS/p‐CT mesophase membrane [p‐CT (A‐M)] was used for the sorption of 1 mol % p‐CT for different times and for the sorption of different concentrations of p‐CT, chlorobenzene (CB), p‐xylene (p‐X), toluene, and chloroform for 48 h. The presence of solvents in the sPS membrane was confirmed by IR analysis. A thermal study revealed that the sorption amount of 1 mol % p‐CT increased with increasing immersion time, and the sorption amounts of different solvents increased with increasing solvent concentration. Differential scanning calorimetry results showed that the desorption peak temperature increased as the amount of the solvent increased in the clathrated sPS membrane. Wide‐angle X‐ray diffraction results showed that 2θ at 8.25° was slightly shifted toward 8°, and there was no change in the peak position at 10° for p‐CT (A‐M), which was immersed in different solvents (1 mol %); however, the intensity of 2θ at 10° was not similar for all the samples. Among the solvents used for the sorption studies at 1 mol %, p‐CT (A‐M) could sorb more p‐CT and CB than p‐X, toluene, and chloroform. The solvent sorption isotherm was the Langmuir sorption mechanism. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3439–3446, 2004     

Toughness mechanism in polypropylene composites: Polypropylene toughened with elastomer and calcium carbonate

Polypropylene (PP) was modified with elastomer or CaCO₃ particles of two different sizes (1 μm and 50 nm) in various volume fractions. The dispersion morphology and mechanical properties of the two systems were investigated as functions of the particle size and volume fraction of the modifier. The brittle‐to‐tough transition occurred when the matrix ligament thickness was less than the critical ligament thickness, which was about 0.1 μm for the PP used here, being independent of the type of modifier. At the same matrix ligament thickness, the improvement of the toughness was obviously higher with the elastomer rather than with CaCO₃, but adding CaCO₃ increased the modulus of PP. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1656–1662, 2004     

介质靶表面的充电效应对等离子体浸没离子注入过程中鞘层特性的影响

针对等离子体浸没离子注入技术在绝缘体表面制备硅薄膜工艺，采用一维脉冲鞘层模型描述介质靶表面的充电效应对鞘层厚度、注入剂量及靶表面电位等物理量的影响.数值模拟结果表明：随着等离子体密度的增高，表面的充电效应将导致鞘层厚度变薄、表面电位下降以及注入剂量增加，而介质的厚度对鞘层特性的影响则相对较小. 关键词： 等离子体浸没离子注入 脉冲鞘层 绝缘介质 充电效应     

Cr3+：MgAl2O4晶体EPR参量及其电子精细光谱的研究

考虑了SS(Spin-Spin)作用和SOO(Spin-Other-Orbit)作用，采用完全对角化方法，结合自旋Hamiltonian理论，研究了Cr³⁺∶MgAl₂O₄晶体EPR参量及其吸收光谱，理论与实验符合甚好. 在此基础上，进一步研究了⁴A₂(3d³)离子EPR参量的微观起源. 研究表明，EPR参量起源于四种微观机制：(1) SO(Spin-Orbit) 耦合机制；(2) SS耦合机制；(3)SOO耦合机制；(4) SO～SS～SOO总联合作用机制. 在这些机制中，SO机制是最主要的.     

Yb:FAP和Yb:C_3S_2-FAP晶体光谱的温度特性和选择激发

报导了Yb :FAP和Yb :C3S2 _FAP晶体在不同温度下的吸收光谱和荧光光谱实验结果 ,研究发现由于电子_声子近共振耦合作用 ,Yb :FAP和Yb :C3S2 _FAP晶体均存在有明显的振动谱 ,Yb :FAP晶体的零声子线在低温下还劈裂为相差 10cm- 1 的两条线 .采用激光选择激发技术研究了Yb3 离子在FAP和C3S2 _FAP晶体中的格位特征 ,结果表明Yb3 离子在这两种基质中都只占据Ca(Ⅱ )格位 ,但由于CaF2 的挥发 ,导致了Ca(Ⅱ )格位的局部畸变 .     

光纤光栅选频掺Yb3+双包层光纤激光器

利用相位掩模法 ,在D形内包层掺Yb3 双包层光纤一端直接写制出Bragg光栅 ,用作双包层光纤激光器的输出腔镜 .试验得到了线宽为 0 196nm ,波长为 10 5 8 2nm ,最高输出功率为 5 70mW的稳定激光输出 ,解决了激光器中模式竞争造成的输出不稳定现象 .从速率方程出发 ,对激光器的输出功率与抽运功率、光栅反射率的关系以及最佳光纤长度进行了理论分析 ,结果与实验符合很好     

强流四脉冲电子束源实验研究

 为了进行强流多电子束源研究，对现有2MeV LIA 注入器进行了四脉冲改造，二极管脉冲电压约500kV。实验研究了天鹅绒阴极在四脉冲条件下的发射能力、传导电流负载效应以及阴极等离子体运动对阴极电子发射和束能量的影响。利用空间电荷限制流模型推算出阴极等离子体膨胀速率在1 ~4cm/μs之间。     

喷气Z箍缩内爆等离子体的雪铲模型

 在喷气Z pinch内爆等离子体研究中，雪铲模型是一种常用的、比较简单的物理模型。根据实验中提供的电流波形，负载线质量和初始半径，可以通过雪铲模型来估算内爆到心的时刻。根据一维运动方程和不同构形下的解析解以及部分实验结果相结合，讨论了雪铲模型的适用范围。数值计算的内爆时间和实验（Gamble II, Double EAGLE, BLACKJACK 5）测量值符合得较好。结果表明，雪铲模型在喷气Z pinch实验的负载优化设计研究中是很有参考价值的方法。     

Nd~(3+):YAG激光的光纤传输

首先叙述了光纤传输Nd~(3+): YAG激光的优点,接着分析了不同光纤和其传输Nd~(3+): YAG激光的特点。然后通过对光纤传输系统各部分的分析与设计,结合实际,设计了光纤耦合机构。最后,对来自于工件反射光问题提出了解决方案。     

Mean value in invexity analysis

In this paper, a generalization of the mean value theorem is considered in the case of functions defined on an invex set with respect to η (which is not necessarily connected).