Thermoanalytical methods in the study of inorganic thin films

Thermoanalytical (TA) methods are relatively seldom applied for assessing the physical and chemical proeprties of thin films, but they can be used in studies of composition, phase transitions and film—substrate interactions. In the present paper the possibilities of TA methods in thin film studies are reviewed. The thermoanalytical methods considered are the classical TG and DTA/DSC methods but some complementary methods will also be briefly mentioned. The main emphasis is given to true thin films. Details of sample preparation are also given. An important application of TA methods is characterization of precursors for the CVD growth of thin films, and this is also discussed.     

The application of dielectric analysis to drying latex films

Measurements of real and imaginary capacitance (C andC) have been made during the drying of a film-forming latex. In one experiment dielectric measurements at frequencies between 1 Hz and 100 kHz were made simultaneously with gravimetric measurements on a microbalance. It was found that both the rate of water evaporation and the a.c. conductance decrease sharply at high polymer volume fraction. These results are discussed qualitatively in terms of a model for the film-forming process. In another experimentC andC were recorded at 10 Hz along with automatic measurements of the build-up of the scratch resistance of the film. It was found that the mechanical response to film-formation appears significantly earlier than the dielectric response. This is also discussed qualitatively in terms of the model.The authors would like to thank Dr. I. Abrahams, Dr. S. Bell, and Dr. M. Reading for useful discussions regarding this work and M. Bahra for his help with the TFA measurements.     

Surfactant in the gaseous phase II. Influence on stability of foams and thin liquid films

The influence of the vapors ofn-amyl orn-decyl alcohol on the stability of single thin liquid films, single bubbles, and foam columns was determined. It was found that the presence of surfactant vapors lowered the stability of foams and single foam films. The mechanism of the destabilizing action of the surfactant vapors on wet, dynamic foams under dynamic conditions is discussed. It is shown that the destabilizing action of the surfactant vapors is a further indication that surface elasticity forces are the main factor determining stability of wet, dynamic foams.     

Smart Biopolymer-Based Nanocomposite Materials Containing pH-Sensing Colorimetric Indicators for Food Freshness Monitoring

Nanocomposite biopolymer materials containing colorimetric pH-responsive indicators were prepared from gelatin and chitosan nanofibers. Plant-based extracts from barberry and saffron, which both contained anthocyanins, were used as pH indicators. Incorporation of the anthocyanins into the biopolymer films increased their mechanical, water-barrier, and light-screening properties. Infrared spectroscopy and scanning electron microscopy analysis indicated that a uniform biopolymer matrix was formed, with the anthocyanins distributed evenly throughout them. The anthocyanins in the composite films changed color in response to alterations in pH or ammonia gas levels, which was used to monitor changes in the freshness of packaged fish during storage. The anthocyanins also exhibited antioxidant and antimicrobial activity, which meant that they could also be used to slow down the degradation of the fish. Thus, natural anthocyanins could be used as both freshness indicators and preservatives in biopolymer-based nanocomposite packaging materials. These novel materials may therefore be useful alternatives to synthetic plastics for some food packaging applications, thereby improving the environmental friendliness and sustainability of the food supply.     

工作气压对磁控溅射ITO薄膜性能的影响

工作气压在ITO薄膜的制备过程中是一个重要的工艺参数,直接决定着薄膜的性能.本文利用射频磁控溅射方法,采用氧化铟锡陶瓷靶材,在衬底温度为175℃,工作气压范围为0.45～1.0 Pa条件下,制备了氧化铟锡透明导电薄膜.研究了工作气压对其微观结构、表面形貌和光电特性的影响.在衬底温度为175℃、纯氩气中制备的氧化铟锡薄膜电阻率为3.04 ×10-4 Ω·cm、可见光波段(400～800 nm)透过率为91.9;,适合用作异质结太阳电池的前电极和减反射膜.     

（Ti,Al）N薄膜光学性能的研究

研究了（Ｔｉ，Ａｌ）薄膜的光学特性，对其反射和透射光谱作了仔细分析。运用Ｈａｄｌｅｙ方程，算出一定成分（Ｔｉ，Ａｌ）Ｎ膜的折射率ｎ，消光系数ｋ随波长的变化关系。又根据透射曲线，计算出了（Ｔｉ，Ａｌ）Ｎ膜的光隙能。     

Effects of laser irradiation on optical properties of a-Se100−x Te x thin films

The effect of laser irradiation on the optical properties of thermally evaporated Se_100?x Te _x (x=8, 12, 16) chalcogenide thin films has been studied. The result shows that the irradiation causes a shift in the optical gap. The results have been analyzed on the basis of laser irradiation-induced defects in the film. The width of the tail of localized state in the band gap has been evaluated using the Urbach edge method. As the irradiation time increases, the values of the optical energy gap for all compositions decrease, while tail energy width increases. It is also observed that the optical energy gap decreases with increasing Te content in the alloy. These changes are a consequence of an increment in disorder produced by laser irradiation in the amorphous structure of thin film.     

Adhesive fracture of heterogeneous interfaces

We have studied the effect of interface heterogeneity on fracture, at both local and global scales. The single cantilever beam adhesion test was used to investigate interfacial fracture between polycarbonate plates and an elastic/fragile epoxy adhesive. Two surface treatments were applied to a (given) polycarbonate plate giving zones of strong and weak adhesion parallel to the crack direction. Calculated fracture energies differed from those expected from a simple rule-of-mixtures. A perturbation method, proposed by Rice, was used and results compared with crack fronts observed in situ. The technique was applied successfully but the difference in values of stress intensity factor between the zones was found substantially different from the experimental value. In an attempt to explain discrepancies, specimens with discontinuous crack fronts (adhesive and/or plates severed along the strong/weak adhesion frontier) were tested. Good agreement was found with the rule-of-mixtures predictions raising questions about the role of crack front continuity in load transfer.     

Characterizing polymer macrostructures by identifying and locating microstructures along their chains with the kerr effect

In this brief report, we demonstrate that Kerr effect measurements, which determine the excess birefringence contributed by polymer solutes in dilute solutions observed under a strong electric field, are highly sensitive to and capable of determining their microstructures, as well as their locations along the macromolecular backbone. Specifically, using atactic triblock copolymers with the same overall composition of styrene (S) and p-bromostyrene (pBrS) units, but with two different block arrangements, that is, pBrS₉₀-b-S₁₂₀-b-pBrS₉₀ (I) and S₆₀-b-pBrS₁₈₀-b-S₆₀ (II), which are indistinguishable by NMR, we detected a dramatic difference in their molar Kerr constants (_mK), in agreement with those previously estimated. Although similar in magnitude, their Kerr constants differ in sign, with _mK(II) positive and _mK(I) negative. In addition, S/pBrS random and gradient copolymers synthesized by reversible addition-fragmentation chain-transfer (RAFT) polymerization exhibit a heretofore unexpected enhanced enchainment of racemic (r) pBrS-pBrS diads. Comparison of their observed and calculated _mKs suggests that the gradient S/pBrS copolymers possess an unanticipated additional gradient in stereosequence that parallels their comonomer gradient, that is, as the concentration of pBrs units decreases from one end of the copolymer chain to the other, so does the content of r diads. This conclusion could only be reached by comparison of observed and calculated Kerr effects, which access the global properties of macromolecules, and not NMR, which is only sensitive to local polymer structural environments, but not to their locations on the copolymer chains. Molar Kerr constants are characteristic of entire polymer chains and are highly sensitive to their constituent microstructures and their distribution along the chain. They may be used to both identify constituent microstructures and locate them along the polymer chain, thereby enabling, for the first time, characterization of their complete macrostructures. © 2013 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013