Reagentless system for sulphite determination based on polyaniline

A new reagentless system for sulphite (or sulphur dioxide) determination is reported based on the use of an organic conducting polymer, polyaniline, and its absorbance variation at 550 nm, depending on the sulphite concentration. After chemical polymerisation of aniline a very thin film of polyaniline is obtained. Although the response is not fully reversible, each film can be used for at least 10 measurements for low analyte concentrations (up to 0.5 mg l⁻¹) and five measurements for higher sulphite concentrations. Moreover, the reproducibility, ease of preparation and low cost of the films, permit the use of a new disposable system for each measurement. When the change in absorbance at 550 nm was measured for 210 s (stabilisation time), the system showed a linear response, which ranged from 0.025 to 1.50 mg l⁻¹ of sulphite. A theory with regard to the reaction mechanism between the polyaniline films and sulphite is also proposed. The system was applied to sulphite determination in wine samples and the results were in agreement with those obtained by the Official Method of Analysis (iodometric titration).     

Evaluation of digestion procedures for the determination of iron and zinc in biscuits by flame atomic absorption spectrometry

An evaluation is made of different digestion methods for the determination of iron and zinc in biscuits prior to flame atomic absorption analysis. For the initial studies, microwave digestion was enough (using hydrogen chloride and nitric acid 3:1, v/v, at 180 °C and 600 W) to provide comparable accuracy, precision, digestion time and non-critical handling of reagents to dry-ashing and wet digestion (using different acid mixtures) and also to a simple acid treatment at room temperature. Although, after a simple microwave digestion, the spiked recoveries were found around 96–102%, to reduce the digestion time and for simplicity we worked on wet acid treatments. The results showed that acid-only treatment is not enough to digest the samples without adding ethanol, which was found necessary to digest organic residue at room temperature. The method was validated by comparison of the data found for commercial biscuit samples through using the proposed procedure and the AOAC official reference spectrophotometric method. Fe concentration in the different biscuits (such as petit beurre, baby biscuits, etc.) ranged from 1.21 to 15.96 mg/100 g while Zn concentration ranged from 0.58 to 2.50 mg/100 g depending on biscuit type. The highest concentration of Fe was in baby biscuits and these biscuits were about thirteen times richer in Fe than petit beurre biscuits.     

Use of modified rice husks as a natural solid adsorbent of trace metals: characterisation and development of an on-line preconcentration system for cadmium and lead determination by FAAS

The use of rice husks as an alternative adsorbent in an on-line preconcentration system for Cd (II) and Pb (II) determination by flame atomic absorption spectrometry (FAAS) is described. The potential of rice husks as a natural adsorbent was evaluated as a material modified with 0.75 mol l⁻¹ NaOH solution and in the unmodified form. For this task, several techniques such as spectroscopy and thermogravimetry were used for elucidation of possible functional groups responsible for the uptake of Cd (II) and Pb (II). Furthermore, based on adsorption studies and adsorption isotherms applied to the Langmüir model, it was possible to verify that modified rice husks present a higher adsorption capacity for both metals. After establishing this material as a promising natural adsorbent, it was used for on-line preconcentration of Cd (II) and Pb (II) metals. The multivariate optimisation of chemical and flow variables was performed by using a full factorial design (2⁴) including the following factors: preconcentration time, preconcentration flow rate, concentration and volume of eluent. The optimum pH values used for on-line preconcentration were taken from prior univariate experiments. Under optimised conditions for Cd (II) determination (4 min of preconcentration at a 6 ml min⁻¹ preconcentration flow rate, in which comprises 24 ml of preconcentration volume, 200 μl elution volume and 1.0 mol l⁻¹ HNO₃ solution as eluent), the system achieved a detection limit of 1.14 μg l⁻¹ and an enrichment factor of 72.4. Similar conditions were used for Pb (II) determination (4 min of preconcentration, 6 ml min⁻¹ preconcentration flow rate, 300 μl elution volume and 1.0 mol l⁻¹ HNO₃ solution as eluent) from which a detection limit of 14.1 μg l⁻¹ and enrichment factor of 46.0 were achieved. Also, rice husks have been shown to be a homogeneous and stable adsorbent in which more than 100 preconcentration/elution cycles provide a relative standard deviation (RSD) of less than 6.0% on the analytical signal. The satisfactory accuracy of the method developed was obtained by using spiked water samples (mineral water and lake water) and spiked red wine samples. These values were confirmed by electrothermal atomic absorption spectrometry (ETAAS). The certified reference material [pig kidney (CRM 186)] and the reference material [beech leaves (CRM 100)] were also used.     

一种测定蛋白质的分子吸收光谱分析新体系

使用四溴荧光素(TBFS)作为蛋白质的染色剂,建立了一种测定蛋白质的分子吸收光谱分析新体系———BSA 四溴荧光素,体系十分简单,BSA浓度在0.11～60.0μg·ml-1范围符合比耳定律;测定15.0μg·ml-1BSA溶液10次,求得相对标准偏差为1.26%,桑德尔灵敏度为0 094μg·cm-2。可直接用于血清样品中蛋白质的测定,测得质量控制血清样品中蛋白质质量为35.4±2.4mg,与标准值36.9mg吻合。回收率在97.0%～108.3%之间,结果满意。     

分析信号处理方法的比较研究

研究了高效液相色谱－火焰原子吸收光谱联用系统分析信号处理方法，比较了各种处理方法的优缺点，用积分与适应平滑法综合处理色谱峰分析信号，不仅能有效地消除噪声，而且能使分析信号得到加强，以测定镍为例，经积分与适应平滑法综合处理后，检出限改善了２．７倍。     

间接原子吸收法测定乳酸环丙沙星

研究了在弱酸性介质中，乳酸环丙沙星与雷氏盐定量生成缔合物的反应条件，以及通过原子吸收法测定沉淀中Cr的含量而间接测定乳酸环丙沙星含量的分析方法。线性范围在5－40mg/L，相对标准偏差为2．5％，回收率在98％－101％之间。     

Water absorption of a diglycidyl ether of bisphenol A/1,3-bisaminomethylcyclohexane (DGEBA/1,3-BAC) epoxy resin system

The diffusive and dynamic mechanical behavior of the DGEBA/1,3-BAC epoxy resin system was studied during water absorption. The diffusion of water was investigated at 100% relative humidity, by immersion of specimens in water at 60, 80 and 100°C. In all absorption experiments, water diffusion followed Fick's law. Diffusion coefficients and saturated water concentrations are given for these temperatures. The activation energy for diffusion was determined from the relationship between the diffusion coefficient and the reciprocal of the absolute temperature. The value obtained was 31.2 kJ mol^–1. Dynamic mechanical analysis of samples immersed in 100°C water and with various water contents showed both a shift of T_g, defined by thetan peak, to lower temperatures and a slight decrease in the dynamic modulus in the presence of water. These effects are probably a result of plasticization.This work was supported by the Xunta de Galicia through grant XUGA-17201A92.     

Synchrotron X-ray absorption of LaCoO3 perovskite

LaCoO₃ perovskite was prepared at 700°C using citrate precursors. The product was then characterized with X-ray diffraction (XRD) and X-ray absorption spectroscopy (XAS). The powder XRD pattern indicates rhombohedral or its monoclinic I2/a subgroup symmetry. The electronic configuration and the short-range atomic structure of the LaCoO₃ perovskite at room temperature were investigated using synchrotron near-edge X-ray absorption spectroscopy (XANES) and extended X-ray absorption spectroscopy (EXAFS). From the XANES region of the XAS we conclude that Co(III) is at least partly in its intermediate- or high-spin state, which is in accordance with most of the published literature on LaCoO₃ perovskite. The EXAFS region of the LaCoO₃ perovskite spectrum, which up to now was almost not investigated, was simulated satisfactorily for the first two radial structure peaks in terms of the dominant scattering contributions generated with the FEFF8 code and the structural information available from crystallographic data. The best simulation results were obtained with I2/a symmetry. The obtained amplitude reduction factor, zero-energy shift and Debye-Waller factors are useful reference values for data analyses of similar compounds like partly substituted LaCoO₃ perovskite, such as La_1−xCa_xCoO₃ or La_1−xSr_xCoO₃, which are materials of technical interest in catalyst and other applications.     

Hydrogen transport through Pd-Ni alloy electrodeposited on Pd substrate

Hydrogen transport through a Pd-Ni alloy electrodeposited on a Pd substrate (Pd-Ni/Pd bilayer symmetric electrode) has been investigated using cyclic voltammetry and a.c. impedance spectroscopy combined with the electrochemical hydrogen permeation method. The permeation build-up current transients and the measured impedance spectra were analyzed using the time-lag method for the bilayer electrode and a complex non-linear least squares data-fitting method based upon the derived Faradaic admittance for the hydrogen absorption into and diffusion through the bilayer electrode under the permeable boundary condition, respectively. The value of the hydrogen diffusivity in the Pd-Ni layer was lower than that in the Pd layer. Furthermore, the values of the charge transfer resistance and equilibrium absorption constant for the Pd-Ni/Pd bilayer electrode were higher than those for the Pd single layer electrode. From the experimental results, the role of the thin Ni(OH)₂ film formed on the Pd-Ni layer surface in the hydrogen transport through the Pd-Ni/Pd bilayer electrode is discussed in terms of its passivating effect and extremely large hydrogen solubility. Received: 22 January 1997 / Accepted: 15 April 1997     

Direct determination of manganese in vitamin-mineral tablets using solid sampling electrothermal atomic absorption spectrometry

Manganese in vitamin-minerals tablets was determined by solid sampling electrothermal atomic absorption spectrometry (SS-ETAAS) using three different calibration methods, namely calibration against aqueous standards, standard addition with aqueous standards on solid samples and calibration against solid certified standards. Samples were only finely ground and introduced directly into the furnace by means of solid autosampler system without any dissolving process. Effects of different calibration techniques, temperatures and heating rates of atomization and pyrolysis steps on the accuracy and precision of the analyte elements were investigated. After optimization of the experimental parameters, there is good agreement (at 95% confidence level) between the results obtained by solid sampling and those obtained by acid digestion of samples.