三种测定蛋白质热稳定性方法的比较

蛋白质的热稳定性一般使用热变性中点温度(melting temperature,T_m)来表示,即蛋白质解折叠50%时的温度. 测定蛋白质T_m值的常用方法有差示扫描量热法(differential scanning calorimetry,DSC)、圆二色光谱法(circular dichroism,CD)和差示扫描荧光法(differential scanning fluorimetry,DSF)等. 为了比较不同方法的检测特点和效果,选择了5种具有不同结构特点的蛋白,分别使用上述方法对其T_m值进行测定. 结果发现,三种方法测得的T_m值整体上较为一致,但也存在一定的差异. 研究还发现,结构更复杂的蛋白,并不一定具有更多T_m值.     

激光干涉光路偏振移相误差分析

成像光谱仪能够获得目标表面图像特征和频谱特性,提高目标识别分析能力,在军用、民用领域有广泛应用。红外焦平面阵列的等光程间隔采样特性是限制光谱仪分辨率的重要因素。激光干涉光路与成像系统同光路,为红外焦平面阵列提供采样触发信号,实现等光程差采样。通过搭建激光偏振移相干涉光路,对干涉信号幅值和相位差进行理论分析和实际验证,最终调试得到两路正交干涉信号,相位差范围为84.6°~93°,反射透射光强幅值比例小于1∶1.05。实验结果表明,干涉光路中1/8波片角度、偏振分光片角度、探测器位置等参数是影响干涉信号幅值和相位差的重要因素。     

大口径离轴凸非球面系统拼接检验技术

针对大口径离轴凸非球面面形检测的困难,本文将光学系统波像差检验技术与子孔径拼接干涉技术相结合,提出了凸非球面系统拼接检测方法。对该方法的基本原理和具体实现过程进行了分析和研究,并建立了合理的子孔径拼接数学模型。当离轴三反光学系统的主镜和三镜加工完成以后,对整个系统进行装调和测试,并依次测定光学系统各视场的波像差分布,通过综合优化子孔径拼接算法和全口径面形数据插值可以求解得到大口径非球面全口径的面形信息,从而为非球面后续加工和系统的装调提供了依据和保障。结合工程实例,对一口径为287 mm×115 mm的离轴非球面次镜进行了系统拼接测试和加工,经过两个周期的加工和测试,其面形分布的RMS值接近1/30λ(λ=632.8 nm)。     

适用于波前处理器的自适应光学系统非共光路像差补偿方法

提出了一种适合硬件形式波前处理器的非共光路像差校正方法.讨论了非共光路像差的产生原因和运用相位差异技术检测非共光路像差的方法.根据波前处理器的工作流程,推导了将非共光路像差折算到波前探测器参考点偏移量的算法,编写了实现算法的主控计算机软件模块.在望远镜光路中以光源为目标开展实验,用本文算法校正后,目标能量集中度提高了17.6%,证明了该方法的可行性.     

低温热分析标准物质的研制

研制了两种0~100℃热分析标准物质,分别为金属镓和水杨酸苯酯标准物质。研制的标准物质具有良好的均匀性和稳定性,采用与NIST,LGC相应标准物质比较的方法定值。NIST为SRM 2234镓,其定值采用288.6~314.35 K范围内的绝热热量计测得温度及热量值;LGC用绝热法为水杨酸苯酯的熔化温度和熔化热定值,两种方法都可以直接溯源至SI单位。对定值结果的不确定度进行了分析和评定。镓和水杨酸苯酯标准物质的熔化温度分别为(29.77±0.20)℃(k=2),(41.81±0.34)℃(k=2);熔化热分别为(80.52±0.48)J/g(k=2),(88.94±0.62)J/g(k=2)。研制的两种标准物质满足国家标准物质的技术要求,申报已获批准。     

Vulcanization kinetics of graphene/styrene butadiene rubber nanocomposites

This paper presents the influence of graphene on the vulcanization kinetics of styrene butadiene rubber （SBR） with dicumyl peroxide. A curemeter and a differential scanning calorimeter were used to investigate the cure kinetics, from which the kinetic parameters and apparent activation energy were obtained. It turns out that with increasing graphene loading, the induction period of the vulcanization process of SBR is remarkably reduced at low graphene loading and then levels off; on the other hand, the optimum cure time shows a monotonous decrease. As a result, the vulcanization rate is suppressed at first and then accelerated, and the corresponding activation energy increases slightly at first and then decreases. Upon adding graphene, the crosslinking density of the nanocomposites increases, because graphene takes part in the vulcanization process.     

Electrospinning of nylon-6,6 solutions into nanofibers: Rheology and morphology relationships

The relationship between the rheological properties of nylon-6,6 solutions and the morphology of their electrospun nanofibers was established. The viscosity of nylon-6,6 in formic acid(90%) was measured in the concentration range of 5 wt%-25 wt% using a programmable viscometer. Electrospinning of nylon-6,6 solutions was carried out under controlled parameters. The chemical structure, morphology and thermal properties of the obtained nanofibers were investigated using Fourier transform infrared spectroscopy(FTIR), scanning electron microscopy(SEM) and differential scanning calorimetry(DSC), respectively. Entanglement concentration(ce) was found to be 15 wt% and a power law relationship between specific viscosity and solution concentration was observed with exponents of 2.0 and 3.3 for semi-dilute unentangled(c ce) and semi-dilute entangled(c ce) regimes, respectively. The diameter and uniformity of the nanofibers were found to be dependent on the viscosity. Moreover, the average diameter of electrospun nanofibers was found to be dependent on zero shear rate viscosity and normalized concentration(c/ce) in a power law relationship with exponents of 0.298 and 0.816, respectively. For nylon-6,6 solutions, the entanglement concentration(ce = 15 wt%) provides the threshold viscosity required for the formation of a stable polymeric jet during electrospinning and producing uniform beadless fibers. For concentrations less than ce, beaded fibers with some irregularities are formed. DSC analysis showed an increase in crystallinity of all electrospun samples compared to original polymer. Furthermore, Based on FTIR spectroscopy, α phase is dominant in electrospun nanofibers and minor amount of β and γ phases is also available.     

Microstructure characterization of short-chain branching polyethylene with differential scanning calorimetry and successive selfnucleation/annealing thermal fractionation

A series of the copolymers of ethylene with 1-hexene(M1–M9) synthesized by metallocene catalyst Et[Ind]2ZrCl2/MAO was studied by differential scanning calorimetry and successive self-nucleation and annealing(SSA) thermal fractionation. The distribution of methylene sequence length(MSL) in the different copolymers was determined using the SSA method. The comonomer contents of samples M4 and M5 are 2.04 mol% and 2.78 mol%, respectively. Both M4 and M5 have low comonomer content and their MSL distribution profiles exhibit a monotonous increase trend with their MSL. The longest MSL of M5 is 167, and its corresponding molar percent is 43.95%, which is higher than that of M4. Moreover, the melting temperature(Tm) of M5 is also higher than that of M4. The comonomer contents of samples M7, M8, and M9 are 8.73 mol%, 14.18 mol% and 15.05 mol%, respectively. M7, M8, and M9 have high comonomer contents, and their MSL distribution profiles display unimodality. M7 has a lower peak value of 33 and a narrow MSL distribution, resulting in a Tm lower than that of M8 and M9. The MSL and its distribution are also key points that influence the melting behavior of copolymers. Sometimes, MSL and its distribution of copolymers have a greater impact on it than the total comonomer contents, which is different from traditional views.     

差示扫描量热法测定比沙可啶的纯度

建立差示扫描量热法测定比沙可啶原料药样品纯度的方法。考察了炉体气氛、升温速率、称样量3个因素对差示扫描量热法测定结果的影响,确定差示扫描量热法最佳实验条件:升温速率为2.0 K/min,称样量为2.0~4.0 mg,炉内气体为静态空气。差示扫描量热法测定比沙可啶样品纯度为99.86%,测定结果的相对标准偏差为0.02%(n=6),差示扫描量热法测定比沙可啶样品纯度值与HPLC测定结果具有良好的一致性。该方法可以快速、准确地测定比沙可啶化学纯度,为比沙可啶纯度测定提供了一种新的分析方法。     

自支撑NH2-MIL-125/聚噁二唑复合正渗透膜的制备及性能

合成了高强度亲水性含羧基聚噁二唑材料(POD-COOH)和含氨基金属有机框架材料(NH₂-MIL-125), 以NH₂-MIL-125为填料, 与POD-COOH基体材料进行溶液共混, 并通过溶液浇铸法制备系列新型自支撑复合正渗透膜, 研究NH₂-MIL-125的引入对复合正渗透膜结构和性能的影响. 研究结果表明, 所制备的系列复合正渗透膜均呈致密结构, 且随着NH₂-MIL-125含量的增加, 复合膜的表面亲水性增加、 电负性增强, 并保持良好的机械性能. 以去离子水为进料液, 1.5 mol/L硫酸钠溶液为汲取液, 对上述自支撑复合膜进行正渗透性能测试, 发现由于消除了传统正渗透膜支撑层的内浓差极化现象, 该新型复合正渗透膜在分离过程中具有优异的正渗透性能.