过氧聚钨酸薄膜上光栅的制备

用过氧聚钨酸（PPTA）水溶液，通过离心涂膜法在显微镜载玻片上制备了具有光滑表面且厚度为100nm的PPTA薄膜，利用PPTA薄膜在紫外光照下可研制光栅以及其它光学元件的薄膜材料，具有很高的利用价值。     

Sn-C60薄膜的紫外吸收光谱和X-射线衍射谱分析

对Sn-C60薄膜进行紫外可见光吸收，X-射线衍射和扫描电镜的测定结果显示，薄膜样品紫外可见光吸收的两个短波段吸收峰比纯C60薄膜的吸收峰显著下降，说明Sn-C60薄膜的电子光吸收跃迁为间接跃迁，能带中有杂质能级的存在；样品的X射线衍射峰则对应于面心立方结构；扫描电镜结果显示薄膜为纳米级颗粒组成。     

Influence of Yb-Doped Nanoporous TiO2 Films on Photovoltaic Performance of Dye-Sensitized Solar Cells

Yb-doped TiO2 pastes with different Yb/TiO2 weight ratios are prepared in the sol-gel process to obtain dyesensitized solar cells （DSCs）. The nanocrystalline size of Yb-TiO2 becomes smaller and the lattice parameters change. Lattice distortion is observed and dark current is detected. It is found that a part of Yb existing as insulating oxide Yb2O3 state acts as barrier layers at the electrode-electrolyte interface to suppress charge recombination. A Yb-doped TiO2 electrode applied in DSCs leads to a higher open-circuit voltage and a higher fill factor. How the Yb-doped TiO2 films affect the photovoltaic response of DSCs is discussed.     

Formation of Interfacial Layers in LaAlO3/Silicon during Film Deposition

We have studied the interracial reactions between amorphous LaAlO3 thin films and Si substrates, using high- resolution transmission electron microscopy and x-ray photoelectron spectroscopy. It has been shown that the interracial layer between LaAlO3 film and Si substrate chemical states show that the ratio of La 4d3/2 to Al 2p is SiLaxAlyOz. The depth distributions of La, Si and Al of the interfacial layer remains unchanged with the depth compared to that of the LaAlO3 film. Moreover, the Si content, in the interracial layer gradually decreases with increasing thickness of the interracial layer. These results strongly suggest that the Al element is not deficient in the interracial layer, as previously believed, and the formation of a SiLaxAlyOz interracial layer is mainly due to the diffusion of Si from the substrate during the LaAlO3 film deposition. With the understanding of the interracial layer formation, ones can control the interface characteristics to ensure the desired performances of devices using high-k oxides as gate dielectrics.     

复合薄膜透湿率对分子筛吸附性能的影响

分子筛经活化后用复合薄膜包装袋封装存放一定时间后使用，由于水汽缓慢渗透和包装袋微量泄漏的存在，可能使分子筛吸湿，从而直接影响其使用效果和有效期，因此试验研究分子筛产品包装贮存前后吸附性能的变化，以验证理论计算结果，并为分子筛应用提供重要的试验依据。     

CHBr薄膜制备的初步研究

碳氢（cH）及其掺杂材料常被用作ICF实验靶丸烧蚀层材料。制备CH薄膜及其掺杂材料的方法有很多，诸如：离子束辅助沉积、离子溅射沉积、低压等离子体化学气相沉积（LPPCVD）等。近年来，详细研究了LPPCVD法制备CH薄膜的制备方法与工艺，形成了比较成熟的技术路线与工艺路线，并为“神光”实验提供了一系列实验靶丸。     

p型导电掺In的SnO_2薄膜的制备及表征

采用溶胶 凝胶提拉法成功地制备了p型导电掺In的SnO2 薄膜 .x射线衍射测试结果表明 ,掺In的SnO2 薄膜保持SnO2 的金红石结构 .吸收谱测试结果表明 ,掺In的SnO2 禁带宽度为 3 8eV .霍尔测量结果表明 ,空穴浓度与热处理温度有很大的关系 ,5 2 5℃为最佳热处理的温度 .铟锡原子比在 0 0 5— 0 2 0范围内 ,空穴的浓度与In的含量有直接的关系 ,并随In含量的增加而增加     

红光激发下掺Ho3+氟化物薄膜的上转换发光

利用激光脉冲沉淀法制备了稀土Ho~(3 )掺杂的氟化物薄膜。观测到处于薄膜中的Ho~(3 )离子在632.8nm红光激发下的上转换发射。这些上转换发射包括:~5S_2→~5I_7,~5F_4→~5I_7和~5S_2→~5I_8。     

热丝加热电流对CH薄膜沉积速率和表面形貌的影响

 热丝辅助裂解法是结合气相沉积制备聚对二甲苯薄膜和热丝化学气相沉积而形成的一种制-CH薄膜的新方法。热丝辅助裂解法的最大特点就是在保持低衬底温度情况下可以获得高沉积速率，而热丝加热电流对薄膜沉积速率和薄膜表面形貌具有重要影响。研究表明，热丝加热电流越大，薄膜沉积速率越高，在加热电流9A时，薄膜沉积速率可达0.002mm/min，同时薄膜表面粗糙度随之增加，薄膜表面也开始出现其它元素污染，因此，一般热丝加热电流选择为7A附近。