Beam pattern of sparse array for passive sonar

This work aims at sparse array without grating lobe for passive sonar, in order to increase frequency band of the passive sonar and reduce the cost. According to traditional method, the distance between two contiguous sensors in sonar array should be less than the wavelength of highest frequency of the signal; otherwise the grating lobe appears on beam pattern. The paper realizes that the conclusion of the grating lobe emergence it is not fit to the passive sonar due to the sine wave signal model in traditional method, in fact the input of passive sonar is random signal. Prom three aspect of the computer simulation, real passive sonar signal and theory analysis, it is revealed that the grating lobe does not appear on beam pattern when the distance between two contiguous sensors in passive sonar array is longer than wavelength of highest frequency. Whitening of the radiated noise can widen the frequency band, to ensure the beam pattern without the grating lobe. The conclusion of the paper is: if the band of radiated noise is wide enough (broader than 1 octave), that the wavelength of signal can be shorter than the distance between two contiguous sensors in passive sonar without grating lobe.     

Temperature-Dependent Electron Transport in In0.5Ga0.5 P/GaAs Grown by MOVPE

Hall effect measurements in undoped In0.5Ga0.5 P/GaAs allo grown by metal organic vapour-phase epitaxy （MOVPE） have been carried out in the temperat.ure range 15-350K. The experimenta.1 results are analysed using a two-band model including conduction band transport calculated using an iterative solution of the Boltz- mann equation. A good agreement was obtained between theory and experiment. The impurity contents of In0.5Ga0.5 P/GaAs alloy, such as donor density ND, acceptor density NA and donor activation energy εD, were also determined.     

强激光与红外光学系统光轴平行性检测方法的探讨

介绍3种可测量强激光发射光轴与红外光轴平行性的方法及每种方法的优缺点，重点研究了利用热靶进行波段转换来测量激光与红外光学系统光轴平行性的方法。该方法是将激光聚焦在热靶上，使热靶产生热量并发出红外光，红外光再经过准直进入被测设备的红外光学系统，从而测量出激光光轴与红外光轴的平行性。热靶材料的选择与激光透过率的确定尤为重要，该方法中选用酚醛树脂作为热靶材料，激光的透过率仅为0.5%。通过与远距离目标靶测量法进行比对实验，发现2种方法得到的测量结果一致，从而验证了这种方法的可行性与正确性。     

减背景的波段选择算法及其在目标探测中的应用

 介绍了正交子空间投影方法，这种方法可将背景信号从接收到的混合光谱中消除，在此基础上运用匹配跟踪算法自动地进行优化波段的选择，达到选择最佳波段进行目标探测的目的。将其运用到大气外目标探测的问题，得到了较好的探测波段的结果，说明此方法选择优化波段进行目标探测是有效的。     

中间层对白色全磷光有机电致发光器件性能的影响

制备了基于蓝色磷光材料bis[3,5-difluoro-2-（2-pridyl）phenyl-（2-earboxypyribyl）iridumⅢ]（FIrpic）、红色磷光材料bis（2-methyldibenzo [f,h]quinoxaline）（acetylacetonate）iridium（Ⅲ）（Ir（MDQ）₂acac）的双波段白光有机电致发光器件。蓝色磷光材料FIrpic被掺杂在一种宽带隙的主体材料1,3-bis（triphenylsilyl）benzene（UGH3）之中,红色磷光材料Ir（MDQ）₂acac被掺杂在主体材料4,4',4"-tris（carbazol-9-yl）triphenylamine（TCTA）之中,并在两发光层之间加入一种宽带隙的空穴传输材料1,3-bis（carbazol-9-yl）benzene（mCP）作为中间层。制备的器件结构为ITO/NPB（40 nm）/TCTA：Ir（MDQ）₂acac 7%（10 nm）/mCP（x nm）/UGH3：Firpic 8%（30 nm）/BPhen（30 nm）/LIF（0.8 nm）/AL（200 nm）。实验结果表明,中间层的加入促进了发光层中电子和空穴的平衡并抑制了发光层之间的能量转移。加入适当厚度的中间层之后,器件的性能得到了明显的提升,相比于无中间层器件,最高电流效率由3.4 cd/A提高到13.2 cd/A。     

离轴X波段五腔高增益速调管放大器

利用辛普森算法求解螺线管线圈内磁场分布,证明了离轴磁场能用于电子束的聚束。利用2维粒子模拟程序建立了X波段五腔高增益速调管放大器模型,整管模拟得到了频率9.45GHz、输出功率300MW、增益50.3dB和效率37.5%的微波输出。依此设计了X波段五腔高增益速调管放大器的三维模型,并将其分别放置在线圈中心轴和离轴54mm的位置进行模拟,模拟结果证明工作在离轴状态的器件同样可以进行微波放大。最后,对一个螺线管线圈内放置七个器件的状态进行了三维模拟,其合成功率输出可达2GW。     

V波段圆波导TE_(01)模式激励器

V波段圆波导TE01模式激励器由矩形TE10模式到矩形TE20模式变换器和矩形TE20模式到圆波导TE01模式变换器组成。采用H面(磁面)转弯激励的方式实现矩形TE10模式到矩形TE20模式的变换;根据圆波导TE01模式的场分布特性,引入过模波导实现了矩形TE20到圆波导TE01的变换。计算结果表明设计的激励器转换效率在95%以上;模式纯度在98%以上的相对带宽可达4.2 GHz;其中在43.4 GHz处的最大转换效率为99.08%,纯度为99.20%。     

晶体摆动场辐射及其共振线附近的粒子运动行为

寻找新光源,特别是短波长相干光源引起了人们的广泛注意,利用晶体摆动场辐射作为短波长相干光源是最有可能的方案之一,本文从势和场的观点出发,把周期弯晶产生的离心力视为离心势,将粒子运动方程化为Duffing型Mathieu方程,从能量观点出发讨论了系统的稳定性,用摄动法对共振线附近粒子的运动行为进行了分析;揭示了系统的跳跃现象和不稳定行为,结果表明,系统的稳定性与其参数有关,适当调节这些参数,系统的分叉和不稳定性原则上可以避免。