凝胶-燃烧法合成YAG∶Eu3+纳米荧光材料的结构和发光性能

Y₃Al₅O₁₂∶Eu nanophosphors were synthesized by a gel combustion method. The structure of phosphors was characterized by XRD and FTIR. YAG phase came to occur when YAG∶Eu precursors were sintered at 800 ℃, although the phase was mainly amorphous. The organic groups pyrolyzed completely and pure YAG phase was obtained in the samples sintered at 900 ℃. In the formation of YAG phase, no intermediate phases such as YAP and YAM were detected. Both ⁵D₀ → ⁷F₁ orange and ⁵D₀ → ⁷F₂ red emission could be observed for all the sintered samples. However, the emission of amorphous samples was greatly different from that of crystalline ones. The former was mainly ⁵D₀→ ⁷F₂ red emission, but the latter was ⁵D₀ → ⁷F₁ orange emission. As sintering temperature rises, the ratio of orange to red for phosphors increases. Eu could be doped up to 8% in YAG host lattice, and fluorescence quenching was absent. It indicated that the gel combustion synthesis method can increase emission intensity and quenching concentration due to a good distribution of Eu³⁺ activators in Y₃Al₅O₁₂ matrix.     

室温离子液体EMIES的标准生成焓

在(298.15 ±0.01) K下用转动弹热量计测定了离子液体硫酸乙酯-1-甲基-3-乙基咪唑(EMIES)及合成它的原料1-甲基咪唑的恒容燃烧热,通过计算得到它们的标准燃烧焓 分别为(－2671±2) 和(－286.3±0.5) kJ·mol－1;标准生成焓 分别为(－3060±3) kJ·mol－1和(－2145±4) kJ·mol－1.结合文献上硫酸二乙酯的标准生成焓数据,得到了合成离子液体EMIES的反应热(－102.3±1.0) kJ·mol－1,与合成实验中观察到的强烈放热现象是一致的.根据离子液体EMIES的热容数据,计算了不同温度下EMIES的标准生成焓.     

Storage-Reduction of NOx over Combined Catalysts of Pt/Ba/Al2O3-Mn/Ba/Al2O3： Carbon Monoxide as Reductant

Storage-reduction of NOx by carbon monoxide was investigated over combined catalysts of Mn/Ba/Al2O3-Pt/Ba/Al2O3. Combination of Mn/Ba/Al2O3 and Pt/Ba/Al2O3 catalysts in different ways showed excellent NOx storage-reduction performance and the content of Pt could be reduced by 50%. Not only the addition of 5Mn/15Ba/Al2O3 to lPt/15Ba/Al2O3 could improve its storage ability, but also enhance the NOx conversion consequently. NOx conversion over the combined catalysts (the combined catalysts I and II) was increased under dynamic lean-rich burn conditions, the maximum NOx conversion increased from 69.4% to respectively 78.8% and 75.7% over two combined catalysts.     

添加剂铜和银离子对MnO2催化燃烧CH4的影响

催化燃烧法，由于起燃温度低、去除率高、适用氧浓度范围大、无二次污染、燃烧缓和等，是国内外治理有机废气时，回收利用能量最有效的方法之一［１］．但目前用于该过程的催化剂中均含有来源有限、价格昂贵的贵金属铂或钯［２］．因此，寻找来源丰富、价格低廉、性能相当...     

氧化条件下NOx催化的甲烷均相部分氧化

考察了没有固体催化剂时NOx对甲烷气相氧化的促进作用.实验结果表明，即使在强氧化条件下（O2/CH4=5），NOx对甲烷部分氧化制一氧化碳仍然有明显的催化活性.在CH4-O2体系中加入0.005％～0.2％的NO后，反应温度可降低200-300 ℃.在反应产物中还可观察到甲醛和乙烯，通过改变反应条件可以控制它们的相对浓度.     

NiO/SnO2-ZrO2催化剂的制备及甲烷燃烧催化性能的研究

利用正交分析，通过溶胶凝胶－超临界干燥及复合浸渍的方法制备了NiO/SnO2-ZrO2催化剂，进行了活性评价，考察了前驱物、NiO、SnO2含量及制备方法对催化剂活性及稳定性的影响，并采用XRD、TEM对催化剂进行了表征分析，结果表明：NiO/SnO2-ZrO2催化剂具有良好的甲烷燃烧催化性能（t100%=640 ℃），其活性、稳定性与制备参数密切相关，其中NiO含量是影响催化剂活性、稳定性的最主要参数，它对催化剂稳定性和活性的影响规律正相反； SnO2组分的添加使ZrO2单斜相稳定，对催化剂起到了良好的稳定化作用，发现当SnO2含量在6 mol％左右时，催化剂具有较好的稳定性；对于制备方法，在凝胶前加入活性组分有利于催化剂的高活性，而在凝胶后加入活性组分，则有利于催化剂保持较好的稳定性；活性组分前驱物对催化剂性能影响不大，采用Ni(NO3)2作为前驱物较为合适。     

煤焦在燃烧过程中孔隙结构变化的模拟

煤焦在燃烧过程中的物理特性，如比表面积和孔径分布会发生连续变化，直接测量煤焦在燃烧过程中的孔隙结构变化很困难，但可以通过合适的数学模型来观察，二维的圆柱孔模型已大量用来对煤焦气化与燃烧过程中表面积和孔隙结构的变化进行模拟，这个模型把孔隙分成两大部分－－大孔与小孔，因为小孔构成比表面的绝大部分，所以在反应过程中比表面积的变化可以由单一小孔模型来拟合，本文采用了用Ｔｓｅｎｇ和Ｅｄｇａｒ提出的孔模型对几     

Catalytic Combustion of Methane over CO1-xMgxO/Al2O3/FeCrAl Monolithic Catalysts

A series of CoxMgxO/Al2O3/FeCrAl catalysts （x=0-1） were prepared. The structures of the catalysts were characterized using XRD, SEM, and TPR analyses. The catalytic activity of the catalysts for methane combustion was evaluated in a continuous flow microreactor. The results indicated that the active washcoats adhered well on the FeCrAl foils. The phases in the catalysts were Co--xMgxO solid solutions, α-Al2O3, and γ-Al2O3. The surface particle size of the catalysts varied with variations in the molar ratios of Co to Mg. The Co component of the Co1_xMgxO/Al2O3/FeCrAl catalysts played an important role in the catalytic activity for methane combustion. In the Co1-xMgxO/AluO3/FeCrAl series catalyst （x=0.2-0.8）, the catalytic activity in terms of x was in the order of 0.5〉0.2〉0.8 under the experimental conditions. The presence of Mg in these catalysts could promote the thermal stability to a large extent. There were strong interactions between the Co1-xMgxO oxides and the AluO3/FeCrAl supports.     

新型反相微乳液制备纳米结构甲烷催化燃烧催化剂La0.95Ba0.05MnAl11O19-α的研究

提出一种由水, 异丙醇, 正丁醇组成的新型微乳液, 并以其为反应介质制备了甲烷高温燃烧La_0.95Ba_0.05MnAl₁₁O_19-a催化剂. 采用¹H NMR, FT-IR, 电导法及激光粒度散射法研究了新型微乳液中水的结构及相特性. 新型微乳液中水的体积分数小于一定值时, 电导率与水含量成非线性关系, k～φ曲线上存在一临界值(φ^P＝0.15). 水质子的化学位移随水含量的降低移向高场. 加入4% D₂O测定的O—D键的伸缩振动随水含量增加而向高波数方向移动. 异丙醇铝在新型微乳液中水解形成的Al(OH)₃ 胶体粒子的粒径范围为226～329 nm. 采用新型微乳液作为反应介质制备的Ba_0.05La_0.95MnAl₁₁O_19-α催化剂的粒径在30 nm, 明显小于纯水制备的样品(100 nm). BET 比表面积为65 m²/g, 比纯水制备样品高出约一倍. XRD结果显示, 1200 ℃焙烧10 h即可获得含单一β-Al₂O₃相的催化剂. Ba_0.05La_0.95MnAl₁₁O_19-α催化剂甲烷催化燃烧的T₁₀为420 ℃, 比纯水制备样品下降了90 ℃. 甲烷催化燃烧活性提高是由于含有较多Mnⁿ+纳米结构六铝酸盐的形成.     

神木煤显微组分加氢热解特性的研究

在加压热天平上终温900℃，升温速率20℃／min,0.1MPa-3MPa的条件下考察了神木煤显微组分加氢热解的热失重行为、半焦元素分布、脱硫脱氮率及半焦的燃烧反应特性。结果表明：镜质组和丝质组的加氢热解失重行为相似，在378℃－718℃出现明显失重峰，但镜质组加氢热解失重峰温低，失重速率大，在实验压力范围（0.1MPa－3MPa)内，随热解压力升高，半焦中C含量增加，H、O含量下降，脱硫脱氮率增加，在压力为3MPa时，镜质组的脱硫率显著高于丝质组，镜质组加氢热解半焦的燃烧反应性高于丝质组半焦，随加氢热解压力的增加，半焦的燃烧反应性表现出先下降后增加的趋势。