有序排列PMMA 模板法合成三维有序纳米孔道MgO

"利用由无乳化剂的乳液聚合法和水浮法联用技术合成得到的有序排列的聚甲基丙烯酸甲酯(PMMA)微球为硬模板,以硝酸镁为镁源,并采用硝酸镁-柠檬酸-乙醇混合溶液浸渍PMMA微球后经干燥以及先后在300 ℃恒温灼烧3 h和500 ℃恒温灼烧5 h,制备出具有有序纳米孔道结构的MgO粒子．应用X射线衍射、高分辨扫描电子显微镜、透射电子显微镜/选区电子衍射以及N2吸附-脱附法等技术表征了PMMA和MgO样品的物理化学性质．结果表明,所得PMMA微球颗粒较为均匀,粒径约为284 nm,且排列规整有序．由PMMA硬模板     

电子束敏感材料的原子尺度结构研究

分子筛和金属有机骨架(MOF)材料以其独特的孔道和骨架结构在催化、 储能、 干燥及净化和吸附分离等领域有着广泛应用, 对其结构的原子尺度表征对于深入理解其构效关系具有重要意义. 但其大孔道结构和有机骨架使得它们对电子束辐照极为敏感, 在常规透射电镜成像模式下结构会很快被破坏变为非晶, 从而无法获得孔道和骨架的原子排列信息. 最近发展起来的基于积分差分相位衬度扫描透射电子显微(iDPC-STEM)技术在电子敏感材料和轻元素组分成像方面展现出明显优势, 使得对多孔骨架材料及烃池物种的表征成为了可能. 本文综述了本课题组近期利用该技术对分子筛和MOF材料原子尺度结构方面的研究. 将iDPC-STEM技术应用到ZSM-5分子筛催化剂中, 实现了对该分子筛的原子级骨架结构的成像分析. 在MOF体系中, 利用该技术观察到MIL-101骨架内部有机连接体与金属节点的配位方式, 在此基础上解析了MIL-101结构中有机配体的连接和金属节点的苯环结构, 并观察了MOF的原子级表面、 界面和缺陷等局域结构特征. 最后对iDPC-STEM技术在原子尺度成像方面的应用潜力进行了总结与展望.     

探讨周期性结构障碍物的声传播和透射

构建了具有周期性结构的一维狭缝障碍屏,用Comsol Multiphysics模拟计算,在较长波段内讨论声波的透射现象.并改变障碍屏的参数,对比不同情况下的声透射,在理论上分析声波的传播过程和透射特征,对照和分析通过Comsol Mul-tiphysics计算的透射谱,说明了声波透射峰的起源和异常透射现象.     

TDX-200TEM物镜磁路缺陷对物镜性能影响研究

基于TDX-200透射电子显微镜(Transmission Electron Microscope,TEM),利用ANSYS软件仿真物镜磁路存在空隙、凹陷、凸起缺陷时物镜轴上的磁场分布,在此基础上利用MEBS软件仿真物镜激励、球差系数等性能参数,分析了各磁路缺陷对物镜分辨率的影响。结果表明,在相同加速电压下,相对于空隙缺陷、凸起缺陷对物镜分辨率的影响,凹陷缺陷对物镜分辨率的影响最大。在200k V加速电压下,当物镜存在直径为0.5mm的半圆形凹陷环缺陷时,实际分辨率相对于理想分辨率的变化量可达到9.68%。     

Synthesis and electrochemical performance of LiNi0.6Co0.2Mn0.2O2 as a concentration-gradient cathode material for lithium batteries

A well-ordered and spherical LiNi0.6Co0.2Mn0.2O2 cathode material was successfully synthesized from Ni and Mn concentration-gradient precursors via co-precipitation. The crystal structure, morphology and electrochemical properties of LiNi0.6Co0.2Mn0.2O2 were characterized by X-ray diffraction, scanning electron microscopy, energy-dispersive spectroscopy, and charge-discharge tests. The material delivered an initial discharge capacity of 174.3 mAh/g at 180 mA/g （1 C rate） between 2.8 and 4.3 V and more than 93.1% of that was retained after 100 cycles. In addition, it also exhibited excellent rate capability, high cut-off voltage and temperature performance.     

Fabrication of hollow silica microspheres utilizing a hydrothermal approach

Hollow silica microspheres(HSMSs) have been successfully fabricated via a facile hydrothermal route using D-glucose as the sacrificial template and sodium silicate powder as the silica precursor.The resulting silica hollow particles were characterized by scanning electron microscopy(SEM),transmission electron microscopy(TEM),X-ray diffraction(XRD),and infrared spectroscopy(IR).The surface area was determined using the BET method.SEM and TEM images exhibited micro-sized silica hollow particles with a size of ~1.5μm.     

Preparation and characterization of Ti0.7Sn0.3O2 as catalyst support for oxygen reduction reaction

Sn-doped TiO_2 nanoparticles with high surface area of 125.7 m~2·g~(-1) are synthesized via a simple one-step hydrothermai method and explored as the cathode catalyst support for proton exchange membrane fuel cells.The synthesized support materials are studied by X-ray diffraction analysis,energy dispersive X-ray spectroscopy and transmission electron microscopy.It is found that the conductivity has been greatly improved by the addition of 30 mol%Sn and Pt nanoparticles are well dispersed on Ti_(0.7)Sn_(0.3)O_2 support with an average size of 2.44 run.Electrochemical studies show that the Ti_(0.7)Sn_(0.3)O_2 nanoparticles have excellent electrochemical stability under a high potential compared to Vulcan XC-72.The as-synthesized Pt/Ti_(0.7)Sn_(0.3)O_2 exhibits high and stable electrocatalytic activity for the oxygen reduction reaction.The Pt/Ti_(0.7)Sn_(0.3)O_2 catalyst reserves most of its electrochemically active surface area(ECA),and its half wave potential difference is 11 mV,which is lower than that of Pt/XC-72(36 mV) under 10 h potential hold at 1.4 V vs.NHE.In addition,the ECA degradation of Pt/Ti_(0.7)Sn_(0.3)O_2is 1.9 times lower than commercial Pt/XC-72 under 500 potential cycles between 0.6 V and 1.2 V vs.NHE.Therefore,the as synthesized Pt/Ti_(0.7)Sn_(0.3)O_2 can be considered as a promising alternative cathode,catalyst for proton exchange membrane fuel cells.     

Study of In Situ Formation of Magnesium Hydroxide Whisker via Basic Magnesium Chloride Whisker Regulated by Organic Parcels at Low Temperature

In this work, we demonstrate an in situ phase conversion from basic magnesium chloride（BMC） into magnesium hydroxide whisker by using polar organic solvent at low temperature. The morphology and phase composition of magnesium hydroxide whiskers prepared at different reaction temperature, alkali concentration and organic solvent were analyzed by X-ray diffraction（XRD） and scanning electronic microscope（SEM）. It was found that when one of the organic solvents such as absolute ethyl alcohol, butanol, polyethylene glycol（PEG-400）, acetone, et al. was selected as the template, the precursor BMC can transform into whisker-like magnesium hydroxide through precipitate transformation in low temperature and non-hydrothermal system. It can be reasonably explained that the regulation of Mg^2＋ solubility by those organic solvents and the sustained release of Mg^2＋ dissolution by organic adsorption played a significant role in the formation of magnesium hydroxide whisker via BMC whisker as the precursor.     

Self-assembly behavior of copolymers with super segregated structure containing fluorinated segments

Copolymers with super segregated structure of hydrophilic methoxy poly（ethylene glycol） （mPEG） and fluorophilic poly（1H,1H,2H,2H-perfluorodecyl acrylate） （PFA） were prepared. And just because of this super segregated structure which was resulted from the extremely strong incompatibility between the two blocks, several interesting self- assembly behaviors of the copolymers were displayed and studied under different conditions. Transmission electron microscope （TEM） showed that with the increase of PFA in the polymerization system, the incompatibility in this super segregated structure became stronger, and the self-assembly behavior changed from ball-like or rod-like to vesicles, and finally collapsed to sheet-like. The self-assembly behavior changed likewise when the initial concentration increased. And the interesting formation of these barrel-like and spindle-like vesicles was finally studied with different cooling speeds. It＇s finally found that with this super segregation structure, these new self-assembly morphology might be formed due to the extremely strong incompatibility between mPEG and PFA segments.     

Electrospinning of nylon-6,6 solutions into nanofibers: Rheology and morphology relationships

The relationship between the rheological properties of nylon-6,6 solutions and the morphology of their electrospun nanofibers was established. The viscosity of nylon-6,6 in formic acid(90%) was measured in the concentration range of 5 wt%-25 wt% using a programmable viscometer. Electrospinning of nylon-6,6 solutions was carried out under controlled parameters. The chemical structure, morphology and thermal properties of the obtained nanofibers were investigated using Fourier transform infrared spectroscopy(FTIR), scanning electron microscopy(SEM) and differential scanning calorimetry(DSC), respectively. Entanglement concentration(ce) was found to be 15 wt% and a power law relationship between specific viscosity and solution concentration was observed with exponents of 2.0 and 3.3 for semi-dilute unentangled(c ce) and semi-dilute entangled(c ce) regimes, respectively. The diameter and uniformity of the nanofibers were found to be dependent on the viscosity. Moreover, the average diameter of electrospun nanofibers was found to be dependent on zero shear rate viscosity and normalized concentration(c/ce) in a power law relationship with exponents of 0.298 and 0.816, respectively. For nylon-6,6 solutions, the entanglement concentration(ce = 15 wt%) provides the threshold viscosity required for the formation of a stable polymeric jet during electrospinning and producing uniform beadless fibers. For concentrations less than ce, beaded fibers with some irregularities are formed. DSC analysis showed an increase in crystallinity of all electrospun samples compared to original polymer. Furthermore, Based on FTIR spectroscopy, α phase is dominant in electrospun nanofibers and minor amount of β and γ phases is also available.