Design of Two-Dimensional Photonic Crystal Edge Emitting Laser for Photonic Integrated Circuits

An edge emitting laser based on two-dimensional photonic crystal slabs is proposed. The device consists of a square lattice microcavity, which is composed of two structures with the same period but different radius of air-holes, and a waveguide. In the cavity, laser resonance in the inner structure benefits from not only the anomalous dispersion characteristic of the first band-edge at the M point in the first Brillouin-zone but also zero photon states in the outer structure. A line defect waveguide is introduced in the outer structure for extracting photons from the inner cavity. Three-dimensional finite-difference time-domain simulations apparently show the in-plane laser output from the waveguide. The microcavity has an effective mode volume of about 3.2（λ/nslab）^3 for oscillation mode and the quality factor of the device including line defect waveguide is estimated to be as high as 1300.     

电流控阈技术及二值 I2L 施密特电路设计

电流控阈技术及二值Ｉ~２Ｌ施密特电路设计黄瑞祥，杭国强（杭州大学电子工程系杭州３１００２８）在数字电路中，以往对施密特电路的分析与研究大多局限于用电压信号来表示逻辑值的电路，例如ＴＴＬ、ＣＭＯＳ、ＥＣＬ等电路［１－３］．然而，对于以电流为信号的电流型?..     

新型气相色谱检测器研制

气相色谱仪是近年来分析测试应用最广泛的仪器之一,气相色谱常用的热导检测器(TCD)应用面广,但灵敏度偏低,且热丝易于烧断,氢焰检测器(FID)灵敏度较高,却对多数无机气体无响应,且必须配备氢气源,使用中具有一定危险性,两者各有局限,为此,研究一种应用广泛,使用简便,高灵敏的气相色谱检测器,已成为广大色谱工作者长期研究的课题。本文所介绍的一种新型气相色谱检测器用催化元件配以专门设计的气路和电路组成,可与现行一些气相色谱仪匹配使用,已成功地进行了许多有机组分及无机气体的分析。1　检测原理汽化后的有机蒸汽或无机可燃气体…     

Novel preparation of organic polymer-based monolithic column by microwave irradation

Microwave irradiation was firstly attempted for the preparation of organic-based monoliths of poly（styrene-divinylbenzene- methacrylic acid）, which single step in situ polymerization was carried out during 15 min. The colunm permeability, electrophoretic and chromatographac behaviors were comparatively evaluated using pressure-assisted CEC, GEC and low pressure-driven separation modes. The largest theoretical plates for the preparing column could be close to 18,0000 plates/m for thiourea in the mode of p-CEC. It provided a viable alternative to traditional initiation means for the perparation of monolithic capillary columns.     

Smith－Hieftje背景校正法空心阴极灯供电条件的选择

本文提出在原子吸收光谱测定中，采用Ｓｍｉｔｈ－Ｈｉｅｆｔｊｅ法校正背景时，空心阴极灯供电条件（即最佳宽窄脉冲电流）的选择依据和选择方法；并给出２４个常见元素的宽窄脉冲电流的选定结果。     

脉冲激光引信用PFM和PWM式LD驱动电路的研究

 在激光引信的通讯系统中，针对引信用脉冲式半导体激光器驱动电路的脉冲宽度、频率、功率可调的需要，根据LD驱动电路的工作原理，建立了LD驱动电路的一般模型。然后用电子多频振荡器提供驱动信号，用双MOS驱动器来驱动半导体激光器，通过大量的实验、仿真、分析、比较，设计出了方便可调的大功率LD的驱动电路，该电路的脉冲频率和脉冲宽度可方便调整。并且该驱动电路的频率调节范围大（10Hz~20kHz）；脉冲宽度可以从几ns到几百ns进行调节，大大提高了激光引信通讯系统的性能与可靠性。     

跳圈实验的启示

楞次定律是电磁感应中一个十分重要的定律,然而,笔者却发现目前教科书中有关楞次定律的表述与"跳圈实验"不完全相符.我认为,该定律的描述存在缺陷,需要纠正.2012年笔者又仔细地重做了跳圈实验,实验结果是成功的,再次证实了楞次定律的描述存在问题.现把这个实验的情况及笔者的分析介绍给大家.笔者实验的目的是要观察"跳圈"(实际就是几个铝和铜的闭合线圈)在下述几种情况下的运动,     

一类非光滑Chua’s电路的同步控制

本文研究两个带x|x|非线性项的Chua’s电路的全局指数同步和全局同步的控制问题.证明这两个系统在未加控制时不可能同步,但设计不同的控制器可以实现这两个系统的全局指数同步和全局同步.     

脉冲电场测试中的激光供电技术

为解决脉冲电场测试系统中的供电问题，设计了一套激光光纤供电系统，该系统由激光器、多模光纤及光电池构成。重点研究了激光器与光纤的耦合问题，设计了透镜系统对激光器输出光束进行准直和压缩。通过MOCVD法研制了GaAs光电池，并制作了椭球形"光伏眼"来提高光电转换效率。仿真和实验表明:采用透镜耦合时，激光器与光纤的耦合效率可达80%以上，远远高于直接耦合时的16%，改进后的"光伏眼"耦合效率相比直接耦合时提高了54.5%，激光供电系统的转化效率在40%以上。该系统的研制为解决脉冲电场的供电问题提供了一种方案。     

基于单片机和光电开关的通用计数器设计

At presrent, the photoelectric switch is more and more widely used in the industrial automation equipment.It can be finished counting industrial products by using the characteristic of the photoelectric switch which can detect the objects without touching them. This design uses the modular design method,including power-supply module, The photoelectric conversion module, optocoupler isolation circuit module, power off protection module, matrix keyboard module, counting module and The display module. It mainly uses 51 single-chip microcomputer to control the system,uses the keilC51 software to design program,uses the Proteus software to complete the simulation. Through the experiment, it proves the design is feasible.