Self-bonding in an amorphous polymer below the glass transition: A T-peel test investigation

Films of amorphous polystyrene (PS) with a weight-average molecular weight (M_w) of 225 × 10³ g/mol were bonded in a T-peel test geometry, and the fracture energy (G) of a PS/PS interface was measured at the ambient temperature as a function of the healing time (t_h) and healing temperature (T_h). G was found to develop with (t_h)^1/2 at T_h = T_g-bulk − 33 °C (where T_g-bulk is the glass-transition temperature of the bulk sample), and log G was found to develop with 1/T_h at T_g-bulk − 43 °C ≤ T_h ≤ T_g-bulk − 23 °C. The smallest measured value of G = 1.4 J/m² was at least one order of magnitude larger than the work of adhesion required to reversibly separate the PS surfaces. These three observations indicated that the development of G at the PS/PS interface in the temperature range investigated (<T_g-bulk) was controlled by the diffusion of chain segments feasible above the glass-transition temperature of the interfacial layer, in agreement with our previous findings for fracture stress development at several polymer/polymer interfaces well below T_g-bulk. Close values of G = 8–9 J/m² were measured for the symmetric interfaces of polydisperse PS [M_w = 225 × 10³, weight-average molecular weight/number-average molecular weight (M_w/M_n) = 3] and monodisperse PS (M_w = 200 × 10³, M_w/M_n = 1.04) after healing at T_h = T_g-bulk − 33 °C for 24 h. This implies that the self-bonding of high-molecular-weight PS at such relatively low temperatures is not governed by polydispersity. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1861–1867, 2004     

Effects of poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] on the charge distributions of low‐density polyethylene/polystyrene blends

The effect of the triblock copolymer poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS) on the formation of the space charge of immiscible low‐density polyethylene (LDPE)/polystyrene (PS) blends was investigated. Blends of 70/30 (wt %) LDPE/PS were prepared through melt blending in an internal mixer at a blend temperature of 220 °C. The amount of charge that accumulated in the 70% LDPE/30% PS blends decreased when the SEBS content increased up to 10 wt %. For compatibilized and uncompatibilized blends, no significant change in the degree of crystallinity of LDPE in the blends was observed, and so the effect of crystallization on the space charge distribution could be excluded. Morphological observations showed that the addition of SEBS resulted in a domain size reduction of the dispersed PS phase and better interfacial adhesion between the LDPE and PS phases. The location of SEBS at a domain interface enabled charges to migrate from one phase to the other via the domain interface and, therefore, resulted in a significant decrease in the amount of space charge for the LDPE/PS blends with SEBS. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2813–2820, 2004     

One-dimensional non-nearest-neighbor random walks in the presence of traps

A one-dimensional lattice random walk in the presence ofm equally spaced traps is considered. The step length distribution is a symmetric exponential. An explicit analytic expression is obtained for the probability that the random walk will be trapped at thejth trapping site.     

Electrochemical characterization of poly(vinylidenefluoride)-zinc triflate gel polymer electrolyte and its application in solid-state zinc batteries

Gel polymer electrolyte (GPE) films comprising of poly(vinylidenefluoride), propylene carbonate, ethylene carbonate and zinc trifluoromethane sulfonate are prepared and characterized. The composition of GPE is optimized to contain minimum liquid components with a maximum specific conductivity of 3.94×10⁻³ S cm⁻¹ at (25±1) °C. A detailed investigation on the properties such as ionic conductivity, transport number, electrochemical stability window, reversibility of Zn/Zn²⁺ couple and Zn/gel electrolyte interfacial stability have been carried out. The ionic conductivity follows a VTF behaviour with an activation energy of about 0.0014 eV. Cationic transport number varies from 0.51 at 25 °C to 0.18 at 70 °C. Several cells have been assembled with GPE as the electrolyte, zinc as the anode, γ-MnO₂ as the cathode and their charge–discharge behaviour followed. Capacity values of 105, 82, 64 and 37 mAh/g of MnO₂ have been achieved at 10, 50, 100 and 200 μA/cm² discharge current densities, respectively. The discharge capacity values are almost constant for about 55 cycles for all values of current densities. Cyclic voltammetric study of MnO₂ electrode in Zn/GPE/MnO₂ cell clearly shows intercalation/deintercalation of Zn²⁺.     

On the role of the interface charge in non-ideal metal–semiconductor contacts

The bias dependent interface charge is considered as the origin of the observed non-ideality in current–voltage and capacitance–voltage characteristics. Using the simplified model for the interface electronic structure based on defects interacting with the continuum of interface states, the microscopic origin of empirical parameters describing the bias dependent interface charge function is investigated. The results show that in non-ideal metal–semiconductor contacts the interface charge function depends on the interface disorder parameter, density of defects, barrier pinning parameter and the effective gap center. The theoretical predictions are tested against several sets of published experimental data on bias dependent ideality factor and excess capacitance in various metal–semicoductor systems.     

Investigation of the Li1+xV3O8 electrode–organic electrolyte interface by scanning photoelectron microscopy

To investigate the formation of a solid electrolyte interface (SEI) on the Li_1+xV₃O₈ electrode surface in the thermodynamic stability range of the organic electrolyte, we applied scanning photoelectron microscopy (SPEM) to a pristine electrode and to an electrode after ten cycles. The F K-edge absorption spectrum of the cycled electrode showed that LiF forms on the electrode surface during the lithium insertion–extraction process in the Li_1+xV₃O₈/Li cell. The photoelectron spectrum for the cycled electrode showed intense spectral features corresponding to Li 1s, F 2s, F 2p, and P 2p electron signals, whereas these spectral features were of negligible intensity for the pristine electrode. The above results give strong support for the formation of an SEI that consists of LiF and compounds containing phosphorus during operation of the battery. The SPEM images also revealed that the fluorine distribution on the surface of the cycled electrode was inhomogeneous.     

Theoretical Studies on the Si（001）-SiO2 Interface Structure

1 INTRODUCTION Silicon and its alloy have been widely applied in such fields as electronic industry, high-temperature structural ceramics, etc. In addition, the researches on silicon and its relevant materials greatly promote the rapid development of modern optics and infor- mation technology. Therefore, more and more at- tention is focused on the structure of silicon, oxide of silicon and the interfaces between silicon and metal or nonmetal. As an ideal passive film on the Si surface, S…     

Statistical Analysis of the Effect of Mineral Admixtures on the Strength of the Interfacial Transition Zone

Microscopic evidence indicates that the thickness of the interfacial transition zone (ITZ) between the aggregate and the cement paste is modified when mineral admixtures partially replace portland cement. Unfortunately, there is limited information on the significance of these microscopic modifications to the mechanical properties of the ITZ. This research reports experimental results on the shear and tensile strength of the ITZ as affected by the addition of the following mineral admixtures: silica fume, fly ash, and natural pozzolan. Statistical analysis was used to identify the significant parameters affecting the tensile and shear strength of the ITZ. Experimental results indicate that not only does the incorporation of silica fume and fly ash increase the strength of the ITZ, these mineral admixtures have a greater influence on the strength increase of the ITZ than in the strength increase of the cement paste.     

Macrodefect-Free Materials: Modification of Interfaces in Cement Composites by Polymer Grafting

MDF materials are chemically bonded ceramic materials free of the macrodefects typical of hydraulic cement-based materials. MDF materials arising through reactions of sulfo-aluminate-ferrite belitic (SAFB) clinkers and/or Portland cements (PC) with two types of water-soluble polymer (hydroxy-propylmethyl cellulose {HPMC}, polyphosphate glass {poly-P}) are discussed. Mixes of low energy SAFB clinkers with Portland cement, HPMC and, especially poly-P comprise promising cross-linked compositions additional to the better known MDF materials formed from high alumina cement with polyvinylalcohol/acetate. The principles of co-ordination of P and C atoms (of the polymer) with Al and Fe atoms (originating from the cement) are highlighted from spectroscopic information on next-nearest-neighbour interactions, along with the effects of second co-ordination spheres. Polymers modify the interface through functional bonding/grafting of polymer chains onto the surfaces of cement grains. Both the cross-linked atomic structure and the interface coincide well with the model of functional polymers and represent a new type of atomic-level structure in polymer-modified cements. Interpretation is based on previous magnetic resonance and thermal analysis studies. The compactness of Al(Fe)-O-P cross-links reduces transport through the interfaces, increasing the interfacial interactions and resisting the unfavourable uptake of moisture and carbonation.