Formation of low-temperature deformation-induced segregations of nickel in Fe–Ni-based austenitic alloys

ABSTRACT

The authors present the results of an investigation in Fe–Ni-Cr austenitic alloys of the low-temperature deformation-induced segregations of nickel that form in the micro regions being (i) located close to grain- and subgrain boundaries and (ii) characteristic of the concentration and magnetic inhomogeneities indicated by the appearance of a dark diffraction contrast at the electron diffraction patterns taken from these regions typical (at the same time) of an enhanced value of Curie temperature. The observed effects were connected with the micro distortions caused by the local change of lattice parameter because of an increase in nickel concentration, as well as in the result of a magnetostriction dilatation. Using methods of the X-ray energy dispersive spectroscopy (XEDS) and atomic-probe body-section radiography (tomography – APT) has made it possible to determine the borders of those regions of austenite that were characteristic of an enhanced concentration of nickel in the fields of the localisation of a deformation-induced segregation of nickel in the vicinity of grain (subgrain) boundaries of austenitic alloys of the types Fe–13Cr–30Ni and Fe–37Ni–3Ti.     

Non-isothermal short-range-order kinetics of binary alloys as influenced by solute-vacancy complexes

A model describing the roles of bound and unbound vacancies is proposed in order to predict defect decay and short-range-order kinetics of quenched binary alloys during linear heating experiments. This is an alternative treatment of a previous approach. The model has been applied to the differential scanning calorimetry (DSC) curves of Cu-5 at.% Zn quenched from different temperatures. An expression to calculate the activation energy for migration of solute-vacancy complexes was also developed which make use of DSC trace data. A value of 89.12±0.32 kJ mol^-1 was obtained for the above alloy. The relative contribution of bound and unbound vacancies to partition of effective activation energy corresponding to the ordering process as influenced by quenching temperature was also assessed. This revised version was published online in July 2006 with corrections to the Cover Date.     

快冷Fe_(71)Al_(29)合金中的两个内耗峰

用一个计算机控制的倒扭摆研究了快冷Fe71 Al2 9合金中的两个内耗峰 .在快冷的Fe71 Al2 9样品中分别在 180℃(P1 ) ,340℃ (P2 )和 5 10℃ (P3)出现了内耗峰 ,而在慢冷的Fe71 Al2 9样品中只发现了P3峰 .快冷样品中的P1 和P2峰在从 6 5 0℃冷却下来的测量过程中或在 35 0℃经过较长时间的时效后消失 ,其峰高随时效时间的增加而下降 ,直至消失 .P1 和P2 峰都有弛豫特征 ,它们的激活能分别为 :H1 =1.0 3± 0 .0 8eV(P1 峰 ) ;H2 =1.6 4± 0 .0 5eV(P2 峰 ) .P1 峰被认为是无序合金中Al原子在四面体点阵内的最近邻运动所引起 ,P2 峰则是无序合金中Al原子在四面体点阵内的次近邻运动所引起     

Mossbauer investigations of corrosion environment influence on Fe valence states in oxide films of zirconium alloys

Mössbauer investigations about iron atom redistribution in oxide films of zirconium alloys subjected to corrosion at 500°C in pure oxygen and water pair have been analysed. The alloys were also subjected to autoclave conditions at a pressure of 10.0 MPa and autoclave conditions at 350°C and at a pressure of 16.8 MPa, using distilled water and water with additives of lithium and fluorine. It is shown that, depending on the corrosion environment, various compounds of iron, such as α-Fe₂O₃, Fe₃O₄, and FeO, as solid solutions of iron in ZrO₂ are formed in oxide films.     

Mössbauer effect study of the decagonal quasicrystal Al65Co15Cu20

The ⁵⁷Fe Mössbauer effect study at 5.0 K and in an external magnetic field of 9.0 T on a high-quality stable decagonal quasicrystal Al₆₅Co₁₅Cu_19.9Fe_0.1 is presented. It is shown that the iron atoms are located in two distinct classes of sites. The values of the principal component of the electric field gradient tensor and the asymmetry parameter at these sites are, respectively, ?1.90(10)?×?10²¹ V/m², 0.97(15) and ?3.95(12)?×?10²¹ V/m², 0.00(17).     

3004铝合金“反常”锯齿屈服现象的研究

在应变速率为5.56×10^-5s^-1—5.56×10^-3s^-1的范围内，在不同温度下(从223K至773K)，对3004铝合金进行系列拉伸试验，探索其锯齿屈服规律；通过激活能的计算、内耗研究、微观组织观察和能谱分析，探讨锯齿屈服的机理与物理本质.结果表明，3004铝合金在形变过程中会出现动态应变时效现象；发现了一种“反常”的锯齿屈服现象：在出现锯齿屈服的温区内，存在锯齿屈服临界应变量转变温度T_t， 关键词： 动态应变时效 锯齿屈服 铝合金 内耗     

STM/AFM studies of the evolution of morphology of electroplated Ni/W alloys

The surface morphology evolution of Ni/W alloys was studied, as a function of the alloy composition. Using the modified plating baths developed in our laboratory recently, electroplated Ni/W alloys with different W content, in the range of 7–67 atom percent (a/o), can be obtained. This was found to lead to different structures, ranging from polycrystalline fcc-Ni type structure to amorphous, followed by orthorhombic with increasing W content in the alloy. Powder XRD was studied to determine the crystal structures. Ex situ STM, AFM and SEM were used to study in detail the surface morphologies of the different alloys, and their evolution with increasing W content.

The important findings are that a mixture of two crystalline forms can give rise to an amorphous structure. Hillocks that are usually a characteristic of epitaxial growth can also exist in the amorphous alloys. Oriented scratches caused by stress can also be formed.

Up to 20 a/o of W is deposited in the alloys in crystalline form, with the fcc-Ni type structure. Between 20 and about 40 a/o an amorphous structure is observed, and above that an orthorhombic crystal structure is seen, which is characteristic of the NiW binary alloy. Careful choice of the composition of the plating bath allowed us to deposit an alloy containing 67 a/o W, which corresponds to the composition NiW₂.     

High-throughput concept for tailoring switchable mirrors

The optical properties, the switching kinetics and the lifetime of hydrogen switchable mirrors based on Mg-Ni alloys are determined with particular regard to the composition of the optically active metal-hydride layer in combination with the thickness of the catalytic capping layer. For this, a high-throughput experiment is introduced. The switching kinetics and the reversibility of switchable mirrors are strongly thickness dependent, though the details hinge on the fine structure of the clustered capping layer. Therefore, the kinetics is correlated with the surface structures of Pd on Mg_yNi_1−y as investigated by scanning tunneling microscopy. The results are explained by the so-called strong metal-support interaction (SMSI) state, characterized by a complete encapsulation of the capping layer clusters by oxidized species originating from the support. The SMSI-effect is less important with increasing Pd-layer thickness, and is suppressed by a good wetting of the Pd-clusters on the optically active film. This explains the critical thickness for the catalyzed hydrogen uptake observed in many switchable mirror systems. Moreover, the degradation of the kinetics during cycling is found to depend on the Pd-layer thickness and on the gas environment. Only films, covered with at least 15 nm Pd, show small degradation caused by the SMSI-effect. The SMSI-effect is partly reversible: after changing the gas environment from hydrogen to oxygen, the oxide on the Pd-clusters can be partly removed.     

一维应变压缩下TC4钛合金绝热剪切研究

 利用内径为57 mm的压缩气炮，在撞击速度为0.2~1.2 km/s（相应的靶中压力为3~15 GPa）范围内进行对称碰撞实验，以研究TC4（Ti-Al6-V4）钛合金在一维应变冲击压缩条件下的绝热剪切现象。对回收得到的受冲击样品，在扫描电镜（SEM）下进行细观金相分析。结果指出，一维应变冲击压缩条件下，TC4钛合金中绝热剪切带产生的对称碰撞速度阈值为500 m/s（相当于样品中的压力为5.87 GPa）；主剪切带与冲击方向约为45°角，带上有圆形和椭圆形两种孔洞且随碰撞速度的增大而增多和长大，这是典型的韧性损伤特征。随碰撞速度增大，产生与主剪切带成15°角的支剪切带。这些与理论预言相符。X射线能谱分析结果指出，剪切带内材料发生了(α+β)→β相的转变，是典型的相变带。剪切带的温度估算与实验提供的信息吻合。     

Effect of carbon content on the microstructure and the cracking susceptibility of Fe-based laser-clad layer

The laser cladding of Fe-based alloys on a medium carbon steel substrate was performed using a CO₂ laser and Ar shielding gas that was blown into a molten pool. The microstructure and cracking susceptibility of the laser-clad layers were studied in terms of carbon additions. Results show that the small change of the carbon content in the alloy powders can obviously change the microstructure and properties of the layers. When the carbon content is in the range of 0.3–0.4 wt.%, the decrease of the carbon content in alloy powders will increase the hardness and toughness of the layers simultaneously under the same process parameters. As a result, crack-free coatings with high hardness can be obtained. As the carbon content increases from 0.2 wt.% to 0.4 wt.%, the segregation ratio of chromium increases, while the segregation ratios of nickel, manganese, and silicon first decrease and then increase. At the same time, a new designing principle concerning the composition and microstructure has been put forward, and the principal mechanisms of strengthening and toughening of the layers are fine-grain strengthening and low carbon martensitic phase transformation strengthening.