Studies on the syntheses of polymetalloxanes and their properties as a precursor for amorphous oxide. IV. Properties of SiO2–TiO2 oxide fibers from polytitanosiloxane

From polytitanosiloxanes (PTS), SiO₂–TiO₂ oxide fibers with fairly good tensile strength were prepared, and their mechanical and thermal properties were investigated. The precursor fibers PTS-0.5 and PTS-1.0 were obtained by dry spinning of a highly viscous PTS solution which were formed as the reaction mixture of silicic acid (SA) with bis(2,4-pentanedionato)titanium diisopropoxide (PTP) in the molar ratios (SA/PTP) of 0.5 and 1.0. The precursor fibers PTS-0.5 were too brittle to measure their tensile strength, whereas PTS-1.0 and the heat-treated fibers were found to have tensile strength of 130 (precursor), 540 (500°C), and 450 (900°C) MPa, respectively. Heat-treatment of the fibers PTS-1.0 at above 1000°C forms anatase and rutile of titanium dioxide. The crystallization is resulted from the unreacted PTP which is not incorporated into the polymer network.     

Synthesis,characterization, and mechanical properties of PMMA/poly(aromatic/aliphatic siloxane) semi-interpenetrating polymer networks

Semi-interpenetrating polymer networks (IPNs) composed of poly(methyl methacrylate) (PMMA) and aromatic/aliphatic siloxanes have been made via sequential and simultaneous polymerizations. As the percentage of aliphatic siloxane increases, flexibility and, in general, toughness of the IPNs increases and clarity is reduced. This loss in clarity is due to the mismatch of refractive indices (1.49 form PMMA vs. 1.43 for aliphatic siloxane). PMMA is quite transparent. On the other hand, in making aromatic siloxane/PMMA IPNs clarity is retained as aromatic siloxane is increased due to better matching refractive index (1.49 for PMMA and −1.49 for poly(diphenyl siloxane)). Gel permeation chromatography (GPC) indicates slightly crosslinked IPNs with the THF soluble portions having number-average molecular weight, M¯_n, of 10⁵–10⁶. NMRs of IPNs essentially show peaks for the components, PMMA and the siloxane, which make up the respective IPNs. ²⁹Si-NMRs indicate cross-linking and grafting. Mechanical properties show increased toughness of IPNs versus PMMA as percentage of siloxane and crosslinker increases, but with a corresponding loss in tensile strength. © 1996 John Wiley & Sons, Inc.     

Flume testing of passively adaptive composite tidal turbine blades under combined wave and current loading

The tidal energy industry is progressing rapidly, but there are still barriers to overcome to realise the commercial potential of this sector. Large magnitude and highly variable loads caused by waves acting on the turbine are of particular concern. Composite blades with in-built bend-twist elastic response may reduce these peak loads, by passively feathering with increasing thrust. This could decrease capital costs by lowering the design loads, and improve robustness through the mitigation of pitch mechanisms. In this study, the previous research is extended to examine the performance of bend-twist blades in combined wave–current flow, which will frequently be encountered in the field. A scaled 3 bladed turbine was tested in the flume at IFREMER with bend-twist composite blades and equivalent rigid blades, sequentially under current and co-directional wave–current cases. In agreement with previous research, when the turbine was operating in current alone at higher tip speed ratios the bend-twist blades reduced the mean thrust and power compared to the rigid blades. Under the specific wave–current condition tested the average loads were similar on both blade sets. Nevertheless, the bend-twist blades substantially reduced the magnitudes of the average thrust and torque fluctuations per wave cycle, by up to 10% and 14% respectively.     

纵横载荷作用下功能梯度梁的弯曲和过屈曲

基于一阶非线性梁理论和物理中面概念,导出了纵横向载荷作用下功能梯度材料(FGM)梁非线性弯曲和过屈曲问题的控制方程,并获得了该问题的精确解;据此解研究了梯度材料性质、外载荷、横向剪切变形以及边界条件等因素对功能梯度材料梁非线性力学行为的影响,分析中假设功能梯度材料性质只沿梁厚度方向,并按成分含量的幂指数函数形式变化。结果表明:纵横载荷共同作用下,功能梯度梁的弯曲构形将有无限多个;随着梯度指数的增大,梁的变形减小,临界载荷升高;随着长高比的增大,横向剪切变形的影响减小。     

水硬性石灰合成及拉破坏特性试验研究

水硬性石灰在欧洲石质文物修复和加固中获得了很大成功。我国的石质文物主要是砂岩,水硬性石灰的修复效果不好。为满足我国石质文物修复和加固的需求,本文以石灰石和黏土为原料,在950℃煅烧不同时间,制备出水硬性石,对试样的成分、微观形貌、收缩率、抗拉强度和拉破坏过程等进行了研究。结果表明:(1)试样中含有水硬性成分2CaO·SiO2(C2S);煅烧8h时,成分与欧洲水硬性石灰NHL5接近;1.5CaO·SiO2·xH2O(C-S-H)和CaCO3的含量随龄期的增加逐渐增加。(2)龄期1~3d,收缩率较小;龄期4~6d,收缩率以线性规律增加;7d以后,收缩率趋于稳定。(3)局部变形区随拉应力的增加而变大,邻近局部变形区逐渐合并,形成面积更大的应变局部化带;载荷超过峰值后,产生微裂隙;随载荷进一步增加,微裂隙扩展,贯穿整个试件,发展成宏观裂隙,使试件破坏。(4)抗拉强度随龄期的增加而增加,水硬性石灰中C-S-H、CaCO3等相互交织,构成空间致密体,使试件力学强度提高。合成的水硬性石灰物理力学性能与欧洲水硬性石灰NHL5相近,并且成分均匀、可控,在石质文物修复和加固工程中具有良好应用前景。     

丙烯酸盐喷膜防水材料在酸碱浸润和冻融循环条件下的耐久性试验分析

丙烯酸盐喷膜防水材料在酸碱溶液浸润和冻融条件下的耐久性能是该类材料在工程应用中较难回避的实际问题,论文采用酸性介质(0.2%的H2SO4溶液)和碱性介质(0.1%NaOH+饱和Ca(OH)2溶液)对该材料进行饱和浸泡并进行冻融循环后,研究了该材料的吸水性、断裂拉伸强度和拉断伸长率的变化规律。试验结果表明:喷膜防水材料在侵蚀-冻融循环作用下,其拉断伸长率和断裂拉伸强度显著降低,且酸性介质对材料拉伸性能的影响较大;材料耐低温冰冻能力较强,耐高温能力较差。反映出丙烯酸盐喷膜防水材料在低温冰冻和碱性介质中耐久性较好,不建议在高温和酸性介质条件下使用。     

转动惯量法在多轴疲劳本构关系预测中的应用

一些金属材料在承担多轴非比例加载过程时,会产生额外非比例附加强化或软化现象,这一现象往往会导致在评估疲劳寿命时因为材料本构关系的不确定而引起预测结果出现较大误差．因此基于单轴疲劳理论得出的寿命预测模型并不能准确地预测多轴非比例疲劳加载下的材料寿命．针对此问题,本文阐述了非比例附加强化效应产生的原因及结果,结合转动惯量法的理论和塑性增量法,建立了预测多轴低周疲劳加载下循环应力-应变曲线的数值计算模型．利用316L 不锈钢试样在5 种加载路径下的实验数据对预测结果进行了验证,结果表明该模型具有良好的预测有效性及精度．     

基于八面体理论的岩石循环加-卸载本构模型及修正

探究岩石的受力特点及破坏特性是研究岩石地下工程安全性的关键,诸多学者都期望能在岩石本构模型的研究上取得突破性进展。在此背景下,提出了一种能够描述循环加-卸载条件下岩石的本构模型。首先,假设岩石的微元强度服从八面体剪应力理论并且微元破坏服从Weibull概率公式,将岩石本构中的损伤变量以及岩石微元强度表达式里包含的损伤因子进行本构变换,得到关于应力、应变等其他表现加-卸载下岩石损伤本构模型的参数,表示出岩石微元强度和损伤变量,再将得到的岩石微元强度和损伤变量代入所提出的岩石本构模型中,并进行等式变换得到一个函数表达式。通过将其与实验数据进行拟合对比分析,得出修正后的拟合参数,将其代入函数式中,得到损伤本构模型的修正式。最后将拟合参数进行必要的敏感性分析,得出各拟合参数的实际物理意义。     

基于内聚力模型的快速荷载下CFRP-混凝土界面剪切剥离模拟

鉴于纤维增强复合材料(Fiber Reinforced Polymer, FRP)已在混凝土结构加固中普遍应用, 能有效提高结构的承载和变形能力. 为揭示动载作用下FRP-混凝土界面的剥离机理, 本文基于ABAQUS平台, 采用内聚力模型模拟CFRP-混凝土界面层, 实现了快速荷载下CFRP-混凝土界面剥离的高效模拟. 结果表明: CFRP表面应变在加载过程中由加载端向自由端方向传递, 随着加载速率的提高, 界面承载能力也随之提高; 界面峰值剪应力也存在显著的应变率效应; 模拟结果与试验结果基本吻合, 说明了新方法的有效性.     

STUDY ON THE PROPERTIES OF BLEND OF NATURAL RUBBER LATEX/METHYL METHACRYLATE GRAFTED RUBBER LATEX BY GAMMA RADIATION

Natural rubber latex(NRL)and methyl methacrylate(MMA)grafted rubber latex were blended in different ratios and irradiated at various absorbed doses by gamma rays from Co-60 source at room temperature.The tensile properties, swelling ratio and permanent set were measured.The maximum tensile strength and modulus at 500% elongation were obtained at an absorbed dose of 8 kGy.Modulus increases from 6.99 MPa to 9.87 MPa for an increase in proportion of MMA grafted rubber from 40% to 60% in the blend at similar absorbed dose.Elongation at break and swelling ratio decrease with increasing absorbed dose as well as the MMA grafted rubber content in the blends.The decreasing trend of permanent set is high up to 5 kGy absorbed dose,and beyond that dose,it becomes almost flat.