Preparation and characterization of mesoporous silica thin films from polyethoxysiloxanes

Tetraethoxysilane (TEOS) and polyethoxysiloxanes (PEOSs; prepared by the acid‐catalyzed hydrolytic polycondensation of TEOS) were subjected to the sol–gel process in the presence of cetyltrimethylammonium bromide (CTAB), respectively. The PEOSs with M_w 700–26,000, as prepared by sol–gel coating of TEOS and PEOS under various conditions, were used. Uniform and crack‐free thin films of thickness 276–613 nm were prepared by spin‐coating of a PEOS solution containing CTAB. When the coating films were sintered at 400 °C, the combustion of ethoxy groups and CTAB took place to provide porous silica thin films. The structure of the thin films was found to be dependent on the molecular weight of PEOS and the molar ratio of CTAB/Si: lamellar or hexagonal phase was observed for M_w less than 15,000 and for CTAB/Si molar ratios greater than 0.10. Honeycomb structures were observed for M_w less than 5000 and for CTAB/Si molar ratios of 0.15. The honeycomb structure was also observed by atomic force microscopy and transmission electron microscope. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2542–2550, 2006     

关于均值KIRCHHOFF板非线性边界镇定问题的几点注记

对于均值K IRCHHOFF板非线性边界镇定问题给出几点注记.首先应用G reen公式对具有非线性边界反馈控制的均值K IRCHHOFF板所决定的非线性系统的能量衰减速度进行了重新推导,从而修正了前人的结果.然后应用极大单调函数的定义和分部积分技巧,对均值K IRCHHOFF板非线性边界镇定问题所决定的非线性算子A的极大单调性给出了重新证明,进而更正了已有文献中相应证明的欠妥之处.     

圆柱型正交各向异性圆形薄板的非线性非对称弯曲问题（Ⅱ）

本文利用“正则摄动法”［２］研究文献［１］中由“两变量法”［３］所得到的关于Ｗｎｍ，和的递推方程和递推边界条件的求解问题。求得了本问题的一致有效渐近解，最后作为实例，我们利用“混合摄动法”［４］研究了轴对称线性弯曲问题，并将所得结果与文献［５］中给出的精确解相比较，两者基本上是一致的。     

双折射双频激光器偏振特性的分析

用激光原理和晶体光学原理分析了腔内加旋光晶体的激光器输出光的偏振特性，实验和分析表明，激光器输出两束不同频率的垂直线偏振光，激光器两端输出光的偏振面有一夹角ａ，且此夹角与晶轴和传光方向的夹角θ有关。理论计算结果在双折射双频激光器的实验结果符合很好。     

微通道板增益疲劳机理研究

微通道板的增益疲劳是微通道板的主要问题之一，本文分析了微通道板的表面结构模型，同通道板活性表面上碱金属的逸出和碳的增加是导致微通道板的增益疲劳的主要原因，另外，探讨碱金属逸出的机理和碳污染的来源，介绍延长微通道板工作寿命的有效方法。     

维生素B类药物在薄层原位的近红外付立叶变换表面增强拉曼光谱

维生素Ｂ类药物在薄层原位的近红外付立叶变换表面增强拉曼光谱汪瑗，于秉正张煦（首都师范大学分析测试中心北京１０００３７）（北京大学分析测试中心北京）关键词维生素Ｂ_１，维生素Ｂ_２，薄层色谱，表面增强拉曼散射，近红外付立叶变换拉曼光谱将薄层色谱（ＴＬＣ）...     

红外镜反射光谱的测试与解析

红外镜反射（infrared specular reflection，简称SR）光谱与被测样品和衬底的折射指数、吸收指数以及入射角有密切关系，往往由之产生畸变。要从红外镜反射技术测得的光谱处理得到人们熟悉的吸收光谱，需要经过较复杂的计算机数学处理。本文通过几个比较特殊的镜反射例子，以说明镜反射光谱的测试和解析必须注意多种影响因素。     

溶液酸度和反应温度对CaMoO4薄膜电化学制备的影响

本工作研究了恒电流电化学技术制备CaMoO₄薄膜工艺中，溶液酸度和反应温度对薄膜形成的影响。结果表明，酸度会影响薄膜的生长时间和光致发光特性，在较低酸度沉积薄膜时，容易造成薄膜的团簇生长和不确定相的形成；适当升高反应温度会加快晶粒的生长、提高薄膜的纯度、增加薄膜发射光谱的相对强度。在CaMoO₄薄膜电化学制备工艺中，溶液pH值控制在12.0附近和反应温度控制在60 ℃的左右比较好。     

Properties of ITO films prepared by reactive magnetron sputtering

Indium tin oxide (ITO) thin films were deposited by mid frequency pulsed dual magnetron sputtering using a metallic alloy target with 10 wt.% tin in an atmosphere of argon and oxygen. The aim of the work was to study the interdependence of structural, electrical and optical properties of ITO films deposited in the reactive and transition target mode, respectively. The deposition rate in the transition mode exceeds the deposition rate in the reactive mode by a factor of six, a maximum value of 100 nm·m min⁻¹ could be achieved. This corresponds to a static deposition rate of 200 nm min⁻¹. The lowest electrical resistivity of 1.1·10⁻³ Ω cm was measured at samples deposited in the high oxygen flow range in the transition mode. The samples show a good transparency in the visible range corresponding to extinction coefficients being below 10⁻². X-ray diffraction was used to characterise crystalline structure as well as film stress. ITO films prepared in the transition mode show a slightly preferred orientation in (211) direction, whereas films deposited in the reactive mode are strongly (222) oriented. Compared to undoped In₂O₃ all samples have an enlarged lattice. The lattice strain perpendicular to the surface is about 0.8% and 2.0% for films grown in the transition and the reactive mode, respectively. Deposition in the transition mode introduces a biaxial film stress in the range of −300 MPa, while stress in reactive mode samples is −1500 MPa.     

Properties and Photoelectrocatalytic Behaviour of Sol-Gel Derived TiO2 Thin Films

Titanium dioxide (TiO₂) thin films have been prepared on indium doped tin oxide (ITO) glass by sol-gel dip-coating method. Properties of the films were determined as a function of heat-treatment by X-ray diffraction, scanning electron microscopy and photoelectrochemical tests. The films heat-treated at higher temperatures show better crystallinity and photoresponse. The microscopic structure on the film after heat-treatment is attributed to the incorporation of organic polymer into the precursor solution. The performance of the electrodes treated at different temperature on photoelectrocatalytic degradation of methyl orange was investigated. The effect of applied potential and the ability of the electrode to be repeatedly used in photoelectrocatalytic degradation were also evaluated.