Solid state NMR characterization of formation of poly(ϵ‐caprolactone)/maghnite nanocomposites by in situ polymerization

Results of multinuclear MAS NMR spectroscopy are reported for poly (ε‐caprolactone)/maghnite nanocomposite formation, with ε‐caprolactone in situ polymerized in the presence of maghnite, a proton exchanged montmorillonite clay. Exfoliated and intercalated materials with different maghnite loading in the range 3–15 wt % were investigated. ¹H NMR evidences Brønsted acid hydroxyl groups in the silicate layers and shows that their broad signal at 7.6 ppm present in the parent clay disappears in the nanocomposite material. ²⁷Al MAS NMR results show that beside the hexacoordinated aluminum signal, two additional peaks corresponding to two different tetrahedral Al sites are present in the clay framework. The NMR signal intensity of only one of them was found to be affected in the nanocomposites compared with the parent maghnite, suggesting that these specific aluminum sites are the reactive ones at the initial stages of the polymerization. However almost no changes occurred in the ²⁹Si NMR spectra, confirming that the polymer grafting, as indicated earlier by atomic force microscopy, took place on the aluminum tetracoordinated sites rather than on the silicon sites. A mechanism of maghnite surface catalyzed polymerization of ε‐caprolactone was proposed, involving Brønsted and Lewis acid sites. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3060–3068, 2007     

AGS能量下π~－π~－的Bose—Einstein关联

全同粒子间的玻色－爱因斯坦关联可以用来研究相对论性核碰撞中次级粒子源分布及有关的物理问题．本文用强子级联模型（ＨＣＭ）模拟２８Ｓｉ（１４．６ＡＧＣＶ／ｃ）＋Ａｕ反应，得到π－粒子的ｆｒｅｅｚｅ－ｏｕｔ状态，进而计算了π－π－关联函数，取得与实验一致的结果．还计算了ｆｒｅｅｚｅ—ｏｕｔπ－源的均方根线度，并讨论了它与拟合方法抽取的源参数间的关系．     

Cellulose-based fibers from liquid–crystalline solutions. II. Processing and morphology of acetate/butyrate esters

Fibers were spun from isotropic and anisotropic dimethylacetamide solutions of cellulose esters. Take-up speeds of the dry jet/wet spinning process varied. Water served as the coagulant. The mechanical properties of the fibers increased as spinning progressed from the isotropic to the anisotropic state of the solution. A trade-off in solubility and fiber properties was noted as the butyryl acetyl ratio decreased. Whereas high butyryl content enhances both overall solubility and the formation of liquid–crystalline solutions at lower concentration, it results in lower fiber modulus and strength. Morphology of the fibers depended on the coagulation rate which was influenced by the concentration of the sppinning solution. The level of orientation and crystallinity of the fibers increased somewhat when they were spun from liquid-crystalline solutions. © 1993 John Wiley & Sons, Inc.     

AN ENCOMPASSING APPROACH TO MODELING FISHERY DYNAMICS: MODELING DYNAMIC NONLINEAR SYSTEMS

Uncertainty about the nature and significance of nonlinearities and the manner in which dynamics affect future realizations makes model specification the most difficult aspect of modeling dynamic systems. By interpreting several popular fishery models as subcases of a nesting dynamic Taylor series approximation, we isolate the specification differences between these models in a way that accounts for commonalities. On the argument that the differences due to alternative nonlinear forms are likely to be small compared to more mundane considerations such as delay difference and general dynamic lag specification, we propose an alternative model that uses the terms from the first order approximation common to all models combined with a data-based determination of the appropriate lags using the methods of state space time series analysis. Finally, the success of the alternative models is judged in an application to Pacific halibut data.     

Electrical properties of polypyrrole/p‐InP structure

The polypyrrole/p‐InP structure has been fabricated by the electrochemical polymerization of the organic polypyrrole onto the p‐InP substrate. The current–voltage (I–V), capacitance–voltage (C–V), and capacitance–frequency (C–f) characteristics of the PPy/p‐InP structure have been determined at room temperature. The structure showed nonideal I–V behavior with the ideality factor and the barrier height 1.48 and 0.69 eV respectively. C–f measurements of the structure have been carried out using the Schottky capacitance spectroscopy technique and it has been seen that there is a good agreement between the experimental and theoretical values. Also, it has been seen that capacitance almost show a plateau up to a certain value of frequency, after which, the capacitance decreases. The higher values of capacitance at low frequencies were attributed to the excess capacitance resulting from the interface states in equilibrium with the p‐InP that can follow the a.c. signal. The interface state density N_ss and relaxation time τ of the structure were determined from C–f characteristics. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1572–1579, 2006     

Partial molal heat capacities of aqueous tetraalkylammonium bromides as functions of temperature

Enthalpies of solution have been measured from 5 to 85°C for aqueous tetraethyl- and tetrapropylammonium bromides, and the integral heat method is employed to evaluate for these electrolytes over a wide temperature range. Data taken from the literature have been used to evaluate for aqueous Bu₄NBr over a similar temperature range. These data, along with similar data for Me₄NBr, previously reported, have been used to evaluate absolute ionic heat capacities. While the absolute values agree only qualitatively with two other methods of division, the temperature dependences of the three methods essentially agree up to 65°C. Heat capacities due to structural effects on the solvent, obtained by subtracting the inherent heat capacities of the ions, are extraordinarily positive for all four tetraalkylammonium ions and have negative temperature coefficients, indicating that all four ions, including the tetramethylammonium ion, are structure-making ions.     

Solid state reactions of nitrogenous heterocyclic compounds(Ⅰ)——Solid state reactions of 3-methyl-l-phenyl-5-pyrazolone with carbonyl compounds

The solid state reaction of 3-methyl-1-phenyl-5-pyrazolone (MPP) with aromatic aldehydes and ke-tones benzil derivatives and imides,and the solid state Michael addition reaction of MPP with 4-arylidene-3-methyl-1-phenyl-5-pyrnzolone 2 were investigated.Some new solid state reactions between the reactants were found,from which a series of new compounds were obtained The structures of the products were identified by IR,1H NMR,MS,elemental analyses and also by X-ray crystal analysis,and the reaction mechanism of MPP with aromatic aldehydes and ketones was proposed     

Fermi and Coulomb correlations in the 21 S state of the helium isoelectronic sequence

The Fermi and Coulomb holes of the 2¹ S state of the helium isoelectronic sequence are investigated. Several interesting differences between the results obtained and those which might be expected on the basis of the corresponding 2³ S state are pointed out and discussed.     

Preparation of Y2Ba4Cu7O15-δ Superconductor without High Oxygen Pressure

The synthesis of bulk Y₂Ba₄Cu₇O_15-δ superconductor at atmospheric oxygen pressure via solid state sintering is reported. Temperature ranging from 860 to 890 °C as well as time interval over 2 to 15 days were used to investigate the formation of the Y₂Ba₄Cu₇O_15-δ phase. A time-temperature profile characterizing the conditions for the preparation of Y₂Ba₄Cu₇O_15-δ phase suggests the optimal condition to be sintering at 890 °C for over 10 days. Detailed results of X-ray diffraction, electrical resistivity, iodometric titration and magnetization measurements are described.     

Amide-water interactions in cosolvent systems. I. Solubilities and apparent molar volumes of methyl paraben

Solubility and apparent molar volume data are used to demonstrate effects of amide alkylation on amide-water interactions at 25° C. Precise measurements were made of the apparent molar volumes of the amides in binary amide-water mixtures using a dilatometric technique. The results show that the apparent molar volumes of alkyl-substituted amides in water pass through a minimum at an amide concentration which varies inversely with the degree of alkylation. Further studies showed that the solubilities of methyl paraben (methyl-p-hydroxybenzoate) and naphthalene in various amide-water solvent systems increased in characteristic fashion with amide alkylation.