Thermal spraying of composites—Manufacturing and post treatment

Composites are materials with an increasing importance for the industry. A newly developed method for fabrication of fibre-reinforced metal matrix composites permits the production of composites with metal or ceramic fibres by thermal spraying. An improvement of coatings properties and the removal of flaws by post treatment is possible. This paper presents the thermal treatment by laser beam, electron beam and hot isostatic pressing (HIP) process and the mechanical treatment by shot peening.Dedicated to Professor Günther Tölg on the occasion of his 60th birthday     

Post‐oxidizing effects on surface characteristics of salt bath nitrocarburized AISI 02 tool steel type

The effect of post‐oxidizing treatment on the characteristics of modified surface layers produced by salt bath nitrocarburizing on the industrial American Iron and Steel Institute (AISI) 02 tool steel types is investigated. Nitrocarburizing treatment is performed for 6 h and 8 h at 570 °C and post‐oxidizing treatment for 30, 60 and 90 min at 520 °C, using argon–steam mixture. Formed layers are characterized by their basic properties such as thickness layer, depth, surface hardness and wear resistance. Detailed estimation of the modified metal surface quality, in terms of chemical composition, formed phases, microstructures and diffusion mechanisms are performed by metallographic techniques, EDX, X‐ray diffraction, scanning electron microscopy (SEM) and glow discharge optical electron spectroscopy (GDOES). The corrosion resistance was investigated in 0.4 M H₂SO₄ solutions, using steady‐state electrochemical polarization methods. The obtained results revealed the existence of a superficial oxide layer which consists of magnetite (Fe₃O₄) and hematite (Fe₂O₃) and the presence of an ε‐phase associated with a small amount of γ′‐phase. Important improvements in wear, microhardness and corrosion resistance occur after these treatments and it is specifically concluded that the sole application of a nitrocarburizing treatment does not significantly ameliorate the corrosion resistance of the as‐received steel. In fact, post‐oxidation treatment contributes to increase corrosion resistance by forming a dense magnetite layer and at the same time, it partially covers the compound layer pores. Copyright © 2009 John Wiley & Sons, Ltd.     

铝板为基础的S掺杂TiO_2催化分解有毒有机气体(英文)

S-doped TiO2(S-TiO2) films were immobilized on flexible low-cost aluminum sheets(S-TiO2-AS) using a sol-gel dipping process and low post-processing temperatures. The photocatalytic degradation of toxic organic vapors using the prepared films was evaluated using a continuous-flow glass tube under visible light exposure. The surface properties of the S-TiO2-AS and TiO2-AS films were examined by scanning electron microscopy, energy-dispersive X-ray spectroscopy, X-ray diffraction, and ultraviolet-visible spectroscopy. The photolysis of benzene, toluene, ethyl benzene, and xylene(BTEX) did not occur on the bare AS. In contrast, the photocatalytic degradation efficiencies of the target pollutants using S-TiO2-AS were higher than those obtained using reference TiO2-AS photocatalyst. In particular, the average photocatalytic degradation efficiencies of BTEX using S-TiO2-0.8-AS(S/Ti ratio = 0.8) over a 3-h process were 34%, 78%, 91%, and 94%, respectively, whereas those of TiO2-AS were 2%, 11%, 21%, and 36%, respectively. The photocatalytic decompo-sition efficiencies of BTEX under visible irradiation using S-TiO2-AS increased with increasing S/Ti ratios from 0.2 to 0.8, but decreased when the ratio further increased to 1.6. Thus, S-TiO2-AS can be prepared using optimal S/Ti ratios. The degradation of BTEX over S-TiO2-AS depended on the air flow rates and initial concentrations of the target chemical. Overall, under optimal conditions, S-TiO2-AS can be effectively applied for the purification of toxic organic vapors.     

Chemoenzymatic Synthesis of Spinosyn A

Following the biosynthesis of polyketide backbones by polyketide synthases (PKSs), post‐PKS modifications result in a significantly elevated level of structural complexity that renders the chemical synthesis of these natural products challenging. We report herein a total synthesis of the widely used polyketide insecticide spinosyn A by exploiting the prowess of both chemical and enzymatic methods. As more polyketide biosynthetic pathways are characterized, this chemoenzymatic approach is expected to become readily adaptable to streamlining the synthesis of other complex polyketides with more elaborate post‐PKS modifications.     

An effective approach to enhanced thermoelectric properties of PEDOT:PSS films by a DES post‐treatment

As conventional organic solvents present inherent toxicity, deep eutectic solvents (DES) have been considered as excellent candidates due to their green characteristics. In this work, thermoelectric properties enhancement of PEDOT:PSS films is achieved by introducing DES as an additive and post‐treatment reagent. Direct addition and post‐treatment approaches lead to a maximum Seebeck coefficient of 29.1 μV K^?1 and electrical conductivity of 620.6 S cm^?1, respectively. In addition, an optimal power factor is obtained by DES post‐treatment, reaching up to 24.08 μW m^?1 K^?2, which is approximately four orders of magnitude higher than the pure PEDOT:PSS. Assuming a thermal conductivity of 0.17 W m^?1 K^?1, the maximum ZT value is estimated to be 0.042 at 300 K. Further, atomic force microscopy and X‐ray photoelectron spectroscopy are performed and suggest that the remarkably enhanced electrical conductivity originates from the removal of the excess insulating PSS and the phase separation between the PEDOT and PSS chains. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 885–892     

Postpolymerization modification of reactive polymers derived from vinylcyclopropane. III. Polymer sequential functionalization using a combination of amines with alkoxyamines,hydrazides, isocyanates,or acyl halides

A new 1,1‐disubstituted‐2‐vinylcyclopropane monomer bearing a ketone and a pentafluorophenyl ester was synthesized and successfully polymerized to yield a polymer with two side chain moieties readily available for post‐polymerization modification. After a quantitative modification of the pentafluorophenyl moiety with amines, a subsequent second functionalization reaction was successfully performed on the ketone moiety leading to a double side‐chain functionalized polymer using two different routes. The first route utilized hydrazide and hydroxylamine derivatives leading to a ketone conversion of 25 to 85%. In the second route, the ketone moiety was first reduced to alcohol (reduction conversion up to 100%) and then converted into the corresponding ester or urethane using acyl halides or isocyanates, respectively, with a conversion ratio of up to 90%. A library of functionalized polymers was synthesized to confirm the effectiveness of this approach. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2841–2849     

Remarkably Enhanced Gas Separation by Partial Self‐Conversion of a Laminated Membrane to Metal–Organic Frameworks

Separation methods based on 2D interlayer galleries are currently gaining widespread attention. The potential of such galleries as high‐performance gas‐separation membranes is however still rarely explored. Besides, it is well recognized that gas permeance and separation factor are often inversely correlated in membrane‐based gas separation. Therefore, breaking this trade‐off becomes highly desirable. Here, the gas‐separation performance of a 2D laminated membrane was improved by its partial self‐conversion to metal–organic frameworks. A ZIF‐8‐ZnAl‐NO₃ layered double hydroxide (LDH) composite membrane was thus successfully prepared in one step by partial conversion of the ZnAl‐NO₃ LDH membrane, ultimately leading to a remarkably enhanced H₂/CH₄ separation factor and H₂ permeance.     

Nox reduction with CO over supported Pd catalysts under simulated post Euro-IV diesel exhaust conditions

The catalytic reduction of NO_x with CO over Pd/Al₂O₃ and Pd/TiO₂/Al₂O₃ under simulated post Euro-IV diesel exhaust conditions was studied. The catalytic activities obtained by using various Pd and TiO₂ loadings and total amounts of reductant and the influence of H₂ and H₂O was investigated.     

Heat capacities,volumes and solubilities of pentanol in aqueous alkyltrimethylammonium bromides

Apparent molar heat capacities and volumes of pentanol, 0.05m in decyl-, tetradecyl- and hexadecyltrimethylammonium bromides micellar solutions, were measured at 25°C. They were assumed to approach the standard infinite dilution values and rationalized by means of previously reported equations following which the distribution constant between the aqueous and the micellar phase, heat capacity, and volume of pentanol in both phases are simultaneously derived. The present results show that the volume of the micellar core does not seem to have a significant effect on the apparent molar volume and heat capacity of pentanol in the micellar phase and on the free energy of transfer of pentanol from the aqueous to the micellar phase. We report an equation correlating the free energy of transfer of alcohols in alkyltrimethylammonium bromides as a function of the number of carbon atoms in the alcohol and surfactant alkyl chain. Also, the apparent molar heat capacities of pentanol in micellar solutions as a function of surfactant concentration show evidence of two maxima, which, by increasing the alkyl chain length of surfactant display an opposite dependence on concentration. The second maximum can be attributed to a sphere to rod transition. The second transition was also found in the case of butoxyethanol in hexadecyltrimethylammonium bromide. It is more difficult to explain the nature of the first maximum although an attempt is made.