The local and the terminal velocities, the size and the degree of bubbles’ shape deformations were determined as a function of distance from the position of the bubble formation (capillary orifice) in solutions of n-octyltrimethylammonium bromide, n-octyldimethylphosphine oxide, n-octyl-β-D-glucopyranoside and n-octanoic acid.
These surface-active compounds have different polar groups but an identical hydrocarbon chain (C8) in the molecule. The motion of the bubbles was monitored and recorded using a stroboscopic illumination, a CCD camera, and a JVC professional video. The recorded bubble images were analyzed by the image analysis software. The bubbles accelerated rapidly and their shape was deformed immediately after detachment from the capillary. The extent of the bubbles’ shape deformation (ratio of horizontal and vertical diameters) was 1.5 in distilled water and dropped rapidly down to a level of ca. 1.05–1.03 with increasing surfactant concentration. After the acceleration period the bubbles either attained a constant value of the terminal velocity (distilled water and high concentrations of the solutions), or a maximum in the velocity profiles was observed (low concentrations). The values of the terminal velocity diminished drastically with increasing concentration, from the value of 35 cm/s in water down to about 15 cm/s, while the bubble diameter decreased by ca. 10% only. The surfactant adsorption at the surface of the bubbles was evaluated and the minimum adsorption coverages required to immobilize the bubbles’ surface were determined. It was found that this minimum adsorption coverage was ca. 4% for n-octyldimethylphosphine oxide, n-octyl-β-D-glucopyranoside, n-octanoic acid and 25% for n-octyltrimethylammonium bromide. The difference in the adsorption coverage together with the surfactants’ surface activities indicate that it is mainly the adsorption kinetics of the surfactants that governs the fluidity of interfaces of the rising bubbles. 相似文献
This study concerns the thermal and mechanical response of several commercial grades of ethylene – tetrafluoroethylene copolymer films. Differential scanning calorimetry was used to show that, although films have similar degrees of crystallinity and melting temperature, the melting endotherms and crystallisation exotherms differ between materials, suggesting small changes in composition between manufacturers. Films were deformed in tension at a range of temperatures and rates. Selected films were unloaded immediately after stretching, and measurement of the elastic recovery highlighted further differences between materials. Batches of films were pre-drawn uniaxially above the glass transition and immediately quenched. When these materials were subsequently re-drawn below the glass transition temperature, most of them exhibited much improved yield stress, modulus and tensile strength (improving by factors of 5, 5 and 4, respectively at a draw ratio of 3), but a reduced strain to failure. In most of the films, the pre-drawing, as well as the initial orientation of the films, is accounted for by a simple shift in the true strain axis. This is indicative of a material response dominated by entropic network stretch. It also suggests that, in the cases where strain superposition does not work, a different arrangement of crystalline lamellae may be present, limiting the extent to which improved properties can be achieved in some materials. 相似文献
The plastic deformation mechanism operating in polymer glasses is analyzed. The whole process consists of two main stages: nucleation of special shear defects, called PSTs (plastic shear transformations), and their disappearance. The important feature of plastic deformation of glasses is the storage of a large amount of internal energy ΔUdef upon straining. Such energy storage is the critical issue for mechanical performance of polymeric material: if the amount of stored energy is high, the appearance of macroscopic failure is very probable while glassy materials collecting a small amount of stored deformation energy are quite ductile. It is proposed that the rate of disappearance of PSTs is a key factor in dissipation of stored deformation energy. A parameter describing the dissipation ability of material upon deformation is introduced. 相似文献
The hysteresis of sorptive deformation of sorbents has been studied for the first time. Based on the results obtained, it is assumed that the deformation of sorbents could be the universal reason for the sorptive hysteresis.For Part 1, see Ref. 1.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 8, pp. 1477–1479, August, 1995. 相似文献