Effect of Inorganic Ions on Oleate Adsorption at a Nigerian Hematite–Water Interface

Using “pure” natural hematite selected from a high silica Nigerian hematitic ore, oleate adsorption densities at the hematite–water interface were determined in the presence of various inorganic ions (anions and cations) of different charges and at varying concentrations. Adsorption density was determined using electrical conductivity measurements. The specific surface area of the hematite particles was determined using the method of adsorption of paranitrophenol in aqueous solution. Inorganic ions in solution depressed oleate adsorption at the aqueous hematite surface. The charge of the ion proved to be the dominant factor determining the depression of oleate adsorption. Ionic strength also was an influence, up to a limiting value at which monolayer oleate coverage of the hematite surface occurred. The inorganic ions in solution are considered to function through nonspecific adsorption in the diffuse region of the electric double layer.     

HSCCS自由基势能面的理论研究

在CCSD(T)/6-311G(d,f)//MP2/6-311G(d,f) ZPE水平下,计算得到含有8个异构体和11个过渡态的HSCCS自由基体系势能面,讨论了异构体的结构与稳定性及异构体之间的异构化过程.结果表明异构体m1的能量最低,除m1以外,异构体m2和m3的能量也比较低,在MP2水平上,过渡态TS1的能量比异构体m2仅高3.9kJ/mol,而在CCSD(T)水平上,TS1的能量比m2低14.6 kJ/mol,这说明异构体m2可以迅速转化为能量更低的m1.异构体m3的能量比异构体m1高49.99 kJ/mol,可以推断,在合适的实验条件下可以观测到异构体m1.     

A Branched Pore Model Analysis for the Adsorption of Acid Dyes on Activated Carbon

A new branched-pore adsorption model has been developed using an external mass transfer coefficient, K _f, an effective diffusivity, D _eff, a lumped micropore diffusion rate parameter, K _b, and the fraction of macropores, f, to describe sorption kinetic data from initial adsorbent-adsorbate contact to the long-term adsorption phase. This model has been applied to an environmental pollution problem—the removal of two dyes, Acid Blue 80 (AB80) and Acid Red 114 (AR114), by sorption on activated carbon. A computer program has been used to generate theoretical concentration-time curves and the four mass transfer kinetic parameters adjusted so that the model achieves a close fit to the experimental data. The best fit values of the parameters have been determined for different initial dye concentrations and carbon masses. Since the model is specifically applicable to fixed constant values of these four parameters, a further and key application of this project is to see if single constant values of these parameters can be used to describe all the experimental concentration-time decay curves for one dye-carbon system.The error analysis and best fit approach to modeling the decay curves for both dye systems show that the correlation between experimental and theoretical data is good for the fixed values of the four fitted parameters. A significantly better fit of the model predictions is obtained when K _f, K _b and f are maintained constant but D _eff is varied. This indicates that the surface diffusivity may vary as a function of surface coverage.     

Optimization of the Conditions for the Cr (III) Adsorption on Activated Carbon

In order to understand the patterns of the adsorption equilibrium of Cr (III) on activated carbon, the adsorption process was studied by two different ways: classical batch experiments on commercial Norit and Merck activated carbons and their oxidized forms in a wide range of pHs; and extended time-based tests at the same pH values on the same adsorbents. This approach allowed us to understand the role of texture, chemical carbon surface functionality and experimental conditions (initial pH of the solution, contact time and adsorbate/adsorbent ratio) on the effectiveness of Cr (III) removal. The adsorption process of Cr (III) at (24 ± 1^∘C) on Merck and Norit activated carbons and their oxidized forms were studied at pH values between 1.5 and 5 (either adjusted or buffered). Chromium concentration was fixed at 200 ppm. The carbon loading ranged from 1.2 to 20 g/l. The carbon/Cr (III) solution contact time was varied from 0.5–1 month to 5 months, to ensure that the saturation of the carbon level was reached. According to the data obtained, the presence of carboxylic groups on carbon surface seems to enhance Cr (III) uptake at initial pH of the solution in the range between 2 and 4. Depending on the nature of the adsorbent surface chemistry, the contact time to reach equilibrium may range from 3 to 5 months. There is an optimum carbon loading which limits the Cr (III) uptake/removal at given pH value. In order to understand the adsorption process, an ion exchange, surface complex and surface precipitation were considered. This paper was presented in the 5th Brazilian Meeting on Adsorption, held at Natal, Brazil, 18-21 July, 2004.     

MoO3、NiO、ZnO在小表面金红石上的分散行为

Dispersion of MoO3, NiO, ZnO on rutile TiO2 with low specific surface area was studied with Mercury Porosimeter, SEM, XPS and Ammonia Extraction method. The dispersion thresholds of MoO3, NiO, ZnO on three rutile TiO2 carriers were obtained with XPS, and com-pared with those on anatase TiO2 with high specific surf are area. Ammonia Extraction method was used to identify the surface oxide species interarting with support surface in different strength and it was found that the proportions of oxides that can not be extracted by ammonia extraction are different for MoO3, NiO and ZnO which are supported on rutile TiO2.     

Isomers of C20: an energy profile III

Semiempirical calculations, at the PM3 level provided within the Winmopac v2.0 software package, are used to geometrically optimize and determine the absolute energies (heats of formation) of a variety of C(20) isomers that are predicted to exist in and around the ring and cage isomers. Using the optimized Cartesian coordinates for the ring and the cage isomers, a saddle-point calculation was performed. The resulting energy profile, consisting of a series of peaks and valleys, is used as a starting point for the identification and location of fifteen additional isomers of C(20) that are predicted to be energetically stable, both via geometry optimizations and force constant analysis. These additional isomers were subsequently determined to lie adjacent to one another on the potential surface and establish a step-wise transformation between the ring and the cage. Transition-state optimization of the Cartesian coordinates at the saddle point between adjacent isomers was performed to quantify the energy of the transition state. The step-wise process from one isomer to another, which extends out over the three-dimensional surface, is predicted to require approximately 15% less energy than that of the direct, two-dimensional transformation predicted in the bowl-cage profile. However, the net atomic rearrangement for the step-wise process is about four times greater than that of the direct process. Although less in energy, the amount of atomic rearrangement in the step-wise process would make the occurrence of such a route prohibitive. Utilizing the direct distance separating the three primary isomers (ring, bowl, cage), the method of triangulation is performed to quantitatively position other C(20) structures on the potential surface, relative to the ring, bowl, and cage isomers.     

The Surface Imprinted Polystyrene Beads Prepared via Emulsion Templates

In this paper, the surface imprinted cross-linked polystyrene beads were prepared via suspension polymerization with styrene (St), divinylbezene (DVB), polyvinyl alcohol (PVA1788),the mixture of Span 85 and xylene or the mixture of Span 85 and paraffin as monomer,cross-linking agent, dispersion stabilizer and templates, respectively. The results indicate that there are dense cavities on the surface of beads, and the diameter and density of cavity are related with the composition and amount of emulsion template. The forming mechanism of cavity from thermodynamics and dynamics was proposed.     

Control of optical properties of gel-derived oxide coating films containing fine metal particles

Control of the optical properties of gel-derived oxide films containing fine metal particles is described. The duration of the aging of Si(OC₂H₅)₄-derived sols and the amount of water for hydrolyzing Si(OC₂H₅)₄ were found to greatly affect the size and the shape of Au particles formed in the silica matrix, and accordingly the optical absorption of the Au/SiO₂ composite films. Employing dielectric media with high refractive indices like TiO₂ was shown to shift the absorption peak of Au particles to longer wavelengths. Pd/TiO₂ and Pt/TiO₂ composite films showed absorption in the visible region.     

Cu/TiO2-NiO上光促表面催化CO2和H2O合成CH3OH反应规律

采用溶胶-凝胶法制备了n(电子型)-p(空穴型) 复合半导体材料0.5％Cu/TiO2-2.0％NiO (w),利用X射线衍射(XRD)、透射电镜(TEM)、红外光谱(IR)、紫外-可见光漫反射(UV-Vis)、程序升温脱附(TPD)技术对材料结构、吸光性能、化学吸附性能进行了表征,研究了该材料对CO2和H2O合成CH3OH的光促表面催化反应(PSSR)规律.结果表明,所制备材料能够明显促进目的反应,室温条件下即有CH3OH生成.在200 ℃下,由于光-表面-热的协同效应,CO2转化率得以提高,且CH3OH的选择性达到87.5％ .根据实验结果,得出CO2在材料表面的卧式吸附态为CH3OH的前驱物,并对PSSR机理进行了讨论.     

Computer simulation of conformational movement based on interconversion phenomena

A computer method has been developed which is an alternative to molecular dynamics in the sense that it pictures conformational motion. It simulates propagation in conformational movement based on conformational interconversion phenomena. The method starts with the knowledge of the topology of the conformational potential energy hyper-surface, which is described by the minima and the transition states. The topology is obtained by the recently described software . The simulation of conformational motion is based on the Boltzmann statistics of movement between the minima and the transition states at a given temperature. The method is illustrated for methyl--glucopyranoside and - -galNAc(1-3)[- -Fuc(1-2)]Gal-O-Me molecules. Conformational transitions of hydroxyl groups as well as glycosidic linkages are discussed.