F／Cl比与Eu~（2＋）：BaFCl中F色心的浓度和光激励截面的关系

研究了Ｅｕ（２＋）：ＢａＦｘＣｌ２在紫外线辐照下的光激励发光。通过改变激励方式及激励光的扫描方向，给出了Ｅｕ（２＋）：ＢａＦｘＣｌ２－ｘ光激励发光过程中，两种Ｆ色心的浓度比值与光激励截面比值的测定方法。利用这种测定方法，进一步研究了两种Ｆ色心的浓度比值和光激励截面比值与Ｆ／ＣＩ比值的关系。     

Dosimetric characterization of the Exradin W1 plastic scintillator detector through comparison with an in-house developed scintillator system

New commercial dosimetry systems need careful characterization and can benefit from the comparison with similar, in-house developed solutions. A comparison between such two dosimetry systems, both based on fibre-coupled organic plastic scintillator detectors, is presented. One system is the Exradin W1, fully commercialized by Standard Imaging, while the other system is the non-commercial ME40 system, developed by DTU Nutech with the aim of fundamental dosimetric research. Both systems employ plastic scintillator detectors that can be considered similar in design, calibrated using the same method, but differing primarily in the signal detection hardware. The two systems were compared with respect to essential dosimetric properties, with the purpose of testing their performance under conditions less well discussed in the literature. A Farmer ionization chamber was used as the primary reference of the comparison. The study demonstrated that the Cerenkov light ratio calibration coefficient of both systems was not constant, but changed systematically with photon beam quality to a maximum difference of 1.1%. Calibration with respect to stem effect correction should therefore be performed for every investigated beam quality when using plastic scintillator detectors. Both systems were found to be dose rate independent, even for the highest instantaneous dose rate evaluated (1.5 mGy per pulse). Low-dose measurements revealed large uncertainties for both systems, although the ME40 system handled short beam deliveries under reference conditions with accuracy and precision within 0.4%. Changes in response due to field size dependence were investigated and found to be as large as 3.3% for the W1 and 5.4% for the ME40, biasing output factor measurements in large fields. Great caution is therefore advised if using either system for measurements in large fields or under circumstances where the fibre irradiation geometry is unfavourable. Measurements of reference dose to water yielded differences up to 1.5% when compared with the Farmer ionization chamber for all investigated beam qualities.     

小麦超弱延迟发光测试系统

应用一种新型高灵敏度光电倍增管作为传感器,设计一套用于检测小麦超弱发光的光子计数测量系统,实现对储藏小麦超弱发光的定量测量.适当安排LED阵列分布,设计适合延迟发光需要的照明系统,通过对白光LED光源辐射等效单光子能量和流明效率的计算,建立起光照度与光子数强度之间的联系,实现了光源照射强度与样品延迟发光强度之间的定量比较.对不同光照强度下小麦样品延迟发光的测试和双曲函数拟合,探讨了小麦超弱延迟发光双曲函数拟合参量的变化规律;发现不同照射强度下存在不同的饱和照射时间;小麦超弱延迟发光强度曲线符合双曲衰减规律,超弱延迟发光持续时间达数小时.通过对光照时间和数据采集时间的精确控制,以及在拟合函数中设置延迟时间参量因子,实现了延迟发光测试数据对应时间点的精确标定.     

Temporal contrast improvement in chirped pulse amplification systems by a four-grating compressor and by spectral modifications

The quest for higher peak focused intensities and better temporal contrast drives one to improve the design of all possible stages of the chirped pulse amplification (CPA) system. In this paper, we have analyzed the role of dispersion and spectral profile on the temporal shape and contrast ratio of the output pulse of a CPA system. The simulations indicate that an initial sech² or a Gaussian pulse in the CPA system is best for a good contrast ratio. Incorporating a four-grating based pulse compressor in the CPA system improves the contrast as well as provides the flexibility to compensate the dispersion upto the fourth order. The simulations also detail the effect of spectral profile tailoring on the contrast ratio and peak power.     

基于半导体光放大器的干涉型器件中噪声特性的分析

分析了基于半导体光放大器(SOA)的干涉仪分别处于“开”、“关”两种工作状态时的输出信噪比及噪声指数,发现当干涉仪处于“开”态时输出信噪比有所恶化,并导出了附加噪声因子的表达式。实验结果进一步证明了理论分析的正确性。     

Effects of Viscosity Ratio on Morphological,Rheological and Mechanical Properties of PP/PBT Melt Spun Alloy Fibers

Phase morphology formation plays an important role in the mechanical properties of polymer alloy fibers. The development of the blend morphology depends not only on the intrinsic properties of the component polymers but also on extrinsic factors such as viscosity ratio, λ, in the melt spinning process. The effects of blend component viscosity ratio on the morphological, rheological, and mechanical properties of polypropylene/poly(butylene terephthalate) (PP/PBT) melt spun alloy fibers were investigated. Accordingly, two kinds of PP as matrix phase and two kinds of PBT as dispersed phase, with various melt viscosity, were physically mixed and then blended during the extrusion step of melt spinning. SEM micrographs and rheological and mechanical properties evaluations showed that the morphology of PP/PBT alloy fibers strongly depend on the viscosity ratio, λ. Finer diameter PBT fibrils were observed for Viscosity ratios less than 1 (λ < 1) compared to samples with λ > 1. The best mechanical properties in alloy fiber samples were obtained for the viscosity ratio closest to unity (sample with λ = 0.9). The lowest differences among measured complex viscosities at various shear rates (0.1, 10, and 100 s^?1) were also observed in samples with λ = 0.9. The results showed that the mechanical properties of alloy fiber samples are affected not only by morphological properties observed at different viscosity ratios but also by the properties of the individual polymer components.     

用HI-13串列加速器质谱装置测量182Hf的研究

¹⁸²Hf的半衰期为(8.90±0.09)Ma, 是一个接近灭绝的放射性核素. 超新星爆炸是自然界中已知的惟一能产生¹⁸²Hf的途径. 因此¹⁸²Hf是研究近1亿年来在地球附近可能发生的超新星事件的理想核素. 另外, ¹⁸²Hf是核工程中特别感兴趣的一个长寿命放射性核素. 精确测量超痕量的¹⁸²Hf对反应堆的设计和核天体物理学以及其他研究领域都是非常重要的. 用加速器质谱有可能实现对超低含量¹⁸²Hf的测量. 在中国原子能科学研究院的HI-13加速器质谱装置上对¹⁸²Hf的测量方法以及样品的化学去钨方法进行了研究, 分别得到了空白样品以及系列标准样品的¹⁸²Hf和¹⁸³W的能量-飞行时间双维谱. ¹⁸²W对¹⁸²Hf计数的贡献是通过测量¹⁸³W的计数归一扣除的. 目前本工作对¹⁸²Hf的测量灵敏度为4.15±10^－11 (¹⁸²Hf/¹⁸⁰Hf比值).     

Effects of duty ratio at low frequency on growth mechanism of micro-plasma oxidation ceramic coatings on Ti alloy

The aim of this work is to study the effects of duty ratio on the growth mechanism of the ceramic coatings on Ti-6Al-4V alloy prepared by pulsed single-polar MPO at 50 Hz in NaAlO₂ solution. The phase composition of the coatings was studied by X-ray diffraction, and the morphology and the element distribution in the coating were examined through scanning electron microscopy and energy dispersive spectroscopy. The thickness of the coatings was measured by eddy current coating thickness gauge. The corrosion resistance of the coated samples was examined by linear sweep voltammetry technique in 3.5% NaCl solution. The changes of the duty ratio (D) of the anode process led to the changes of the mode of the spark discharge during the pulsed single-polar MPO process, which further influenced the structure and the morphology of the ceramic coatings. The coatings prepared at D = 10% were composed of a large amount of Al₂TiO₅ and a little γ-Al₂O₃ while the coatings prepared at D = 45% were mainly composed of α-Al₂O₃ and γ-Al₂O₃. The coating thickness and the roughness were both increased with the increasing D due to the formation of Al₂O₃. The formation of Al₂TiO₅ resulted from the spark discharge due to the breakdown of the oxide film, while the formation of Al₂O₃ resulted from the spark discharge due to the breakdown of the vapor envelope. The ceramic coatings improved the corrosion resistance of Ti-6Al-4V alloy. And the surface morphology and the coating thickness determined the corrosion resistance of the coated samples prepared at D = 45% was better than that of the coated samples prepared at D = 10%.     

二次风率对分级进风燃烧室内湍流燃烧与NOx生成的影响

本文在分级进风燃烧室的热态实验装置上,测量了燃烧室内湍流燃烧的温度场和组分浓度场,研究了分级进风的流量比率即二次风率对燃烧及NOx生成的影响.得到了四组不同二次风率下燃烧室内气体温度和O2、CO2、CO与NO浓度的分布.     

Representation surfaces of Young''s modulus and Poisson''s ratio for BCC transition metals

 The general expressions for the compliance , Young's modulus E(h k l) and Poisson's ratio υ(h k l) along an arbitrary direction [h k l] are given for cubic crystals. The representation surfaces, for which the length of the radius vector in the [h k l] direction equals to E(h k l) or υ(h k l), are constructed for seven BCC transition metals Cr, Fe, Mo, Nb, Ta, V and W. Neglecting W, which is isotropic, both representation surfaces of Young's modulus and Poisson's ratio are spherical surfaces. The remaining BCC transition metals may be grouped into two classes. In the first group (Cr, Mo, Nb and V) with negative values of s_A, Young's modulus surface has eight depressed corners and six rounded protuberances at the centers of the faces. In the second group (Fe and Ta) with positive values of s_A, on the contrary, Young's modulus surface has eight rounded protuberance corners and six depressions at the centers of the faces. The contrary conclusions are obtained for Poisson's ratio.