Graphene‐Functionalized 3D‐Carbon Fiber Electrodes – Preparation and Electrochemical Characterization

Graphene nanosheets were produced on the surface of carbon fibers by in situ electrochemical procedure including oxidative and reductive steps to yield first graphene oxide, later converted to graphene. The electrode material composed of graphene‐functionalized carbon fibers was characterized by scanning electron microscopy (SEM) and cyclic voltammery demonstrating superior electrochemical kinetics comparing with the original carbon paper. The interfacial electron transfer rate for the reversible redox process of [Fe(CN)₆]^3?/4? was found ca. 4.5‐fold higher after the electrode modification with the graphene nanosheets. The novel electrode material is suggested as a promising conducting interface for bioelectrocatalytic electrodes used in various electrochemical biosensors and biofuel cells, particularly operating in vivo.     

单层MXene纳米片Ti2N电磁特性的过渡金属(Sc、V、Zr)掺杂效应

二维材料MXene纳米片由于具有较大的比表面积和较高的电子迁移率而受到广泛的关注。本文采用基于密度泛函理论的第一性原理计算,对单层MXene纳米片Ti₂N电磁特性的过渡金属(Sc、V、Zr)掺杂效应进行了系统研究。结果表明,所有过渡金属掺杂体系结合能均为负值,结构均稳定;其中Ti₂N-Sc体系的形成能为-2.242 eV,结构更易形成,且保持稳定;掺杂后Ti₂N-Sc、Ti₂N-Zr体系磁矩增大;此外,Ti₂N-Sc体系中保留了较高的自旋极化率,达到84.9%,可预测该体系在自旋电子学中具有潜在的应用价值。     

水热法制备二氧化锡/钨酸铋复合光催化材料及其催化活性研究

本文用水热法制备了正交晶系的纳米球状结构的二氧化锡和正交晶系的由片状聚集成球状结构的钨酸铋,并且对二者进行了复合,制备出了二氧化锡/钨酸铋复合光催化材料。采用X射线衍射(XRD)、扫描电子显微镜(SEM)、比表面积测试仪(BET)、紫外可见分光光度计等技术对复合样品的结构、形貌、比表面积、孔容孔径和光学性质进行了表征。用碘钨灯模拟太阳光,分别以二氧化锡、钨酸铋和二氧化锡/钨酸铋复合材料为催化剂降解罗丹明B(RhB),研究所制备的二氧化锡/钨酸铋复合材料的光催化活性。光催化90 min时二氧化锡、钨酸铋和二氧化锡/钨酸铋对罗丹明B的降解率分别是9%、22%和30%。实验结果表明,在可见光下,二氧化锡/钨酸铋复合材料的光催化活性要高于单一的二氧化锡和钨酸铋。     

Determination of Ti-6242 α and β slip properties using micro-pillar test and computational crystal plasticity

The properties and behaviour of an α−β colony Ti-6242 alloy have been investigated at 20 °C utilising coupled micro-pillar stress relaxation tests and computational crystal plasticity. The β-phase slip strength and intrinsic slip system strain rate sensitivity have been determined, and the β-phase shown to have stronger rate sensitivity than that for the α phase. Close agreement of experimental observations and crystal plasticity predictions of micro-pillar elastic-plastic response, stress relaxation, slip activation in both α and β-phases, and strain localisation within the α−β pillars with differing test strain rate, β morphology, and crystal orientations is achieved, supporting the validity of the properties extracted. The β-lath thickness is found to affect slip transfer across the α−β−α colony, but not to significantly change the nature of the slip localisation when compared to pure α-phase pillars with the same crystallographic orientation. These results are considered in relation to rate-dependent deformation, such as dwell fatigue, in complex multiphase titanium alloys.     

Turbulence in microfluidics: Cleanroom-free,fast, solventless,and bondless fabrication and application in high throughput liquid-liquid extraction

This paper addresses an important breakthrough in the deployment of ultra-high adhesion strength microfluidic technologies to provide turbulence at harsh flow rate conditions. This paper is only, to our knowledge, the second reporting on the generation of high flow rate-assisted turbulence in microchannels. This flow solves a crucial bottleneck in microfluidics: the generation of high throughput homogeneous mixings. We focused on the fabrication of bulky polydimethylsiloxane (PDMS) microchips (without any interfaces) rather than the laborious surface modifications that were employed in the first reporting about turbulence-assisted microfluidics. The fabrication is cleanroom-free, simple, low-cost, fast, solventless, and bondless requiring only a laboratory oven. More specifically, our method relies on the shaping of a nylon scaffold, cure of PDMS with embedded nylon, and removal of this scaffold. The scaffold was obtained by manually wrapping nylon threads. The withdrawing out of the scaffold was completed in few seconds using only a plier. Such microchannels endured flow rates of up to 60.0 mL min⁻¹ with a strikingly low elastic deformation. The importance in producing turbulence into microscale channels was successfully shown in liquid-liquid extractions. The great energy dissipation rate relative to the turbulence created high throughput and efficient extractions in microfluidics for the first time. The residence time was only 0.01 s at 25.0 mL min⁻¹ (total flow rate of the immiscible phases). In addition, the partition coefficient determined in a single run was similar to that obtained by the conventional batch shake-flask method that was realized in triplicate.     

Strain rate effects on compressive behavior of covalently bonded CNT networks

In this study, strain rate effects on the compressive mechanical properties of randomly structured carbon nanotube (CNT) networks were examined. For this purpose, three-dimensional atomistic models of CNT networks with covalently-bonded junctions were generated. After that, molecular dynamics (MD) simulations of compressive loading were performed at five different strain rates to investigate the basic deformation characteristic mechanisms of CNT networks and determine the effect of strain rate on stress–strain curves. The simulation results showed that the strain rate of compressive loading increases, so that a higher resistance of specimens to deformation is observed. Furthermore, the local deformation characteristics of CNT segments, which are mainly driven by bending and buckling modes, and their prevalence are strongly affected by the deformation rate. It was also observed that CNT networks have superior features to metal foams such as metal matrix syntactic foams (MMSFs) and porous sintered fiber metals (PSFMs) in terms of energy absorbing capabilities.     

非磁化等离子体和磁化等离子体的电磁辐射特性研究

本文研究非磁化和磁化双MAXWELL分布等离子体的电磁不稳定性色散方程和电磁辐射增长率.结果表明,非磁化等离子体不能辐射出电磁波,而磁化等离子体能够辐射出电磁波.并分析讨论了磁化等离子体在不同参数下的电磁辐射增长率随辐射频率、等离子体密度和温度的变化.     

热丝加热电流对CH薄膜沉积速率和表面形貌的影响

 热丝辅助裂解法是结合气相沉积制备聚对二甲苯薄膜和热丝化学气相沉积而形成的一种制-CH薄膜的新方法。热丝辅助裂解法的最大特点就是在保持低衬底温度情况下可以获得高沉积速率，而热丝加热电流对薄膜沉积速率和薄膜表面形貌具有重要影响。研究表明，热丝加热电流越大，薄膜沉积速率越高，在加热电流9A时，薄膜沉积速率可达0.002mm/min，同时薄膜表面粗糙度随之增加，薄膜表面也开始出现其它元素污染，因此，一般热丝加热电流选择为7A附近。     

高压、高应变率与低压、高应变率实验的本构关联性

 指出Johnson-Cook（J-C）、Zerilli-Armstrong（Z-A）、Bodner-Parton（B-P）本构方程在一定条件下的适用性,表明对于低压、高应变率实验,单一曲线假定似乎可以采用。通过等效应力、等效应变,可以将不同应力状态下的流动应力函数采用统一的方程描述。然而,这些本构方程的确立,并不包括平面冲击波实验。对适合于平面冲击波实验的Steinberg-Cochran-Guinan（SCG）本构方程,讨论了其方程中所包含的高压与高应变率耦合效应。指出,以剪切模量度量的流动应力具有应变率相关性。基于温度效应的新发现以及直接测量平面冲击波流动应力的新进展,分别用J-C本构及SCG本构方程估算了钨材料在高压、高应变率加载下的流动应力。结果表明,采用J-C本构估算的流动应力仅在压力为10 GPa以下才能与实验数据相近,当压力高于10 GPa时,流动应力只能采用SCG本构估算。也指出了高压、高应变率本构方程与低压、高应变率本构方程所对应的不同物理背景。     

全空间上一类非齐次椭圆方程正解的衰减

本文研究了非齐次椭圆方程不同衰减正解的存在性和衰减问题.利用上下解方法,得到了两个有着不同衰减的正解的存在性,推广了文献[2]中非齐次方程正解的存在性.