Decreasing the Displacements of a Composite Saddle-Shaped Cable Roof

The structural possibilities of decreasing the compliance of a composite saddle-shaped cable roof having a compliant support contour are investigated. The use of a supporting contour consisting of cables joined together with tie-bars is considered as a structural method enabling one to decrease the compliance of the roof. Each cable of the support has its own initial flexure. The method is most efficient from the viewpoint of material consumption per unit of covered area relative to the increasing rigidity and prestress level of the cable net.The efficiency of the method was evaluated by a numerical experiment, which was carried out for a composite saddle-shaped cable roof 50 × 50 m in the plan. The roof was formed by two orthogonal cable groups joined with a compliant supporting contour. A hybrid composite cable based on a carbon-fiber-reinforced plastic, a glass-fiber-reinforced plastic, and steel was considered as a material for the cable net in combination with steel. The material consumption and the maximum vertical displacement of the cable net in relation to the initial geometrical characteristics of the supporting contour were obtained. A possibility of decreasing the maximum vertical displacements of the roof by 8% was established.     

Fully developed mixed convection in horizontal and inclined tubes with uniform heat flux using nanofluid

Fully developed laminar mixed convection of a nanofluid consists of water and Al₂O₃ in horizontal and inclined tubes has been studied numerically. Three-dimensional elliptic governing equations have been solved to investigate the flow behaviors over a wide range of the Grashof and Reynolds numbers. Comparisons with previously published experimental and numerical works on mixed convection in a horizontal and inclined tube are performed and good agreements between the results are observed. Effects of nanoparticles concentration and tube inclinations on the hydrodynamics and thermal parameters are presented and discussed. It is shown that the nanoparticles concentration does not have significant effects on the hydrodynamics parameters. Heat transfer coefficient increases by 15% at 4 Vol.% Al₂O₃. Skin friction coefficient continually increases with the tube inclination, but the heat transfer coefficient reaches a maximum at the inclination angle of 45°.     

Stress concentration and effective stiffness of aligned fiber reinforced composite with anisotropic constituents

The paper addresses the problem of calculation of the local stress field and effective elastic properties of a unidirectional fiber reinforced composite with anisotropic constituents. For this aim, the representative unit cell approach has been utilized. The micro geometry of the composite is modeled by a periodic structure with a unit cell containing multiple circular fibers. The number of fibers is sufficient to account for the micro structure statistics of composite. A new method based on the multipole expansion technique is developed to obtain the exact series solution for the micro stress field. The method combines the principle of superposition, technique of complex potentials and some new results in the theory of special functions. A proper choice of potentials and new results for their series expansions allow one to reduce the boundary-value problem for the multiple-connected domain to an ordinary, well-posed set of linear algebraic equations. This reduction provides high numerical efficiency of the developed method. Exact expressions for the components of the effective stiffness tensor have been obtained by analytical averaging of the strain and stress fields.     

Numerical Prediction of the Strain State of Thermoset Matrix/Mineral Filler Composite Plates

The numerical prediction of the fields of inelastic strains (the linear invariant of the tensor of inelastic strains) in thermoset polyester/marble filler composite plates is discussed. A uniformly distributed load is applied to the plates, which lie on a steel base. The strain fields are predicted by means of the boundary element method by using creep test data for the composites and the polyester matrix itself. Identical creep tests were performed for two ages of the materials (1 month and 13 years), which allowed evaluating the aging effect. The study is carried out in two stages. At the first stage, the application of the generalized Maxwell-Gurevich equation to the thermoset matrix/mineral filler composite is demonstrated. The model parameters determined from the experimental creep data is used for the second stage, where the state of inelastic strains in the plates is predicted by applying the boundary element method. The influence of composite formulation (filler content) and physical aging of the polyester matrix on the state of inelastic strains in the plates is shown.__________Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 41, No. 2, pp. 145–156, March–April, 2005.     

用毛细管测量纯水表面张力系数的误差讨论

通过用毛细管测量纯水表面张力系数实验，得到管内径d与接触角θ的相对误差之间的关系曲线，由此说明实验测得的表面张力系数α和理论公式相比呈现一定的偏差，并简单地讨论了实验的理想状态与实际情况的差别．     

Free boundary viscous flows at micro and mesolevel during liquid composites moulding process

Numerical simulation aspects, related to low Reynolds number free boundary viscous flows at micro and mesolevel during the resin impregnation stage of the liquid composite moulding process (LCM), are presented in this article. A free boundary program (FBP), developed by the authors, is used to track the movement of the resin front accurately by accounting for the surface tension effects at the boundary. Issues related to the global and local mass conservation (GMC and LMC) are identified and discussed. Unsuitable conditions for LMC and consequently GMC are uncovered at low capillary numbers, and hence a strategy for the numerical simulation of such flows is suggested. FBP encompasses a set of subroutines that are linked to modules in ANSYS. FBP can capture the void formation dynamics based on the analysis developed. We present resin impregnation dynamics in two dimensions. Extension to three dimensions is a subject for further research. Several examples are shown and efficiency of different stabilization techniques are compared. Copyright © 2004 John Wiley & Sons, Ltd.     

Composite Silica Particles Using a Mixture of Organosilane Monomers

Composite silica particles were synthesized by a two-step (acid-base) process in an aqueous solution with a mixture of organoalkoxysilane monomers. The two-step process separates the hydrolysis and condensation procedures to easily control condensation rate. In this study, the silane monomers used were phenyltrimethoxysilane (PTMS), vinyltrimethoxysilane (VTMS), methyltrimethoxysilane (MTMS), and tetraethyl-orthosilicate (TEOS). The physical properties of the resultant composite particles were investigated with the change in the molar ratio of monomers. The size of the particles increased with increasing the molar ratio of R_aSi(OR)₃/R_bSi(OR)₃ or R_aSi(OR)₃/TEOS (R_a: phenyl; R_b: vinyl, methyl).     

螺旋线径向挤压变形对其慢波结构冷测特性的影响

 介绍了用MAFIA软件的准周期边界条件计算螺旋线行波管慢波结构的色散和耦合阻抗，以及用ANSYS软件对螺旋线径向挤压变形建模的方法，并对螺旋线受挤压径向变形对其冷测特性的影响进行了详细的分析。结果表明:螺旋线径向挤压变形会导致相速增大，而在通常的变形范围内耦合阻抗也会增加；当变形继续增大时耦合阻抗上升到最大值后开始下降。     

Two-Layered Poly-o-phenylenediamine/Polyaniline Composite: Electrosynthesis and Spectroelectrochemical Properties

Spectroelectrochemical properties of poly-o-phenylenediamine (PPD) and the synthesized composite of PPD and polyaniline—two chemically related polymers containing an amino-substituted benzene ring but having different conduction nature—are studied. The polyaniline synthesis on PPD-modified electrodes involves stages of the reaction initiation, the copolymer formation, and the formation of a polyaniline layer at the copolymer/solution interface.     

A relaxed model and its homogenization for nematic liquid crystals in composite materials

We analyse a model for equilibrium configurations of composite systems of nematic liquid crystal with polymer inclusions, in the presence of an external magnetic field. We assume that the system has a periodic structure, and consider the relaxed problem on the unit length constraint of the nematic director field. The relaxation of the Oseen–Frank energy functional is carried out by including bulk as well as surface energy penalty terms, rendering the problem fully non‐linear. We employ two‐scale convergence methods to obtain effective configurations of the system, as the size of the polymeric inclusions tends to zero. We discuss the minimizers of the effective energies for, both, the constrained as well as the unconstrained models. Copyright © 2004 John Wiley & Sons, Ltd.