格兰-汤普森棱镜胶合层的膜效应分析

将格兰-汤普森棱镜两半块之间的光学胶合层作为一层薄膜,利用薄膜光学理论,分析了胶合层对棱镜透射比的影响。通过研究胶合层的厚度以及光学胶折射率对入射光在胶合界面上反射率的影响,得出了s偏振光经过格兰-汤普森棱镜后的透射比。结果表明：胶合层的厚度以及光学胶折射率对棱镜的透射比均有影响,且厚度对棱镜透射比的影响呈现周期性变化;而光学胶折射率则对透射比的振荡幅度产生影响。以长度孔径比为3的格兰-汤普森棱镜为例,光学胶折射率为1．510时,棱镜的透射比在92．5％～90．8％之间振荡;光学胶的折射率在接近e光主折射率1．475～1．495之间取值时,棱镜透射比的振荡幅度较小。这一结果有利于对格兰-汤普森棱镜性能的优化。     

Rate sensitivity and deformation mechanism of semi-crystalline polymers during instrumented indentation

Instrumented indentation tests using both constant loading rate (CLR) and continuous stiffness measurement (CSM) operation modes were performed to investigate the deformation mechanism and their sensitivity to the deformation rate in semi-crystalline polymers through the quantitative analysis of load-depth loading and unloading curves. The strain rate was constant during the CSM tests, while the strain rate decreased with the increasing of loading time in CLR tests. The mechanical response mechanism of the semi-crystalline polymers to these tests was very complicated because of the combined effects of strain-hardening in the crystal phase and strain-softening in the amorphous phase. Results show that the loading index m reflects the strain-hardening or strain-softening response during indentation. When m > 2, the mechanical response was due to the strain-hardening, and when m < 2, the response was due to strain-softening. A method based on the measured contact hardness was proposed to obtain the unloading stiffness, and the other mechanical parameters could then be determined according to the unloading stiffness.     

水稻叶片叶绿素、类胡萝卜素含量估算的归一化色素指数研究

测定了水稻叶片的高光谱反射率,以及相应的叶绿素、类胡萝卜素含量,采用一种将350～2 500 nm范围内所有光谱波段两两组合的方法,构建所有可能的归一化比值色素指数,并建立这些指数与叶绿素、类胡萝卜素含量的统计模型,然后将构成最佳模型的指数确定为最适合相应色素估算的指数,并进行验证以及与已知归一化色素指数进行了比较。结果表明,本研究所给出基于叶片水平的色素指数(R_{1 729}-R₇₀₇)/(R_{1 729}＋R₇₀₇),(R_{1 554}-R₅₇₂)/(R_{1 554}＋R₅₇₂),(R_{1 729}-R₇₀₆)/(R_{1 729}＋R₇₀₆),(R_{1 536}-R₇₀₇)/(R_{1 536}＋R₇₀₇)可以较好地估算叶绿素、类胡萝卜素含量。构成这些色素指数的指数波段主要位于700 nm附近,其次为绿光长波区域;构成指数的参照波段主要位于短波红外区域。这说明短波红外区域在色素指数的构建中也有重要作用。这些色素指数对叶绿素、类胡萝卜素含量的估算效果一般要好于各已知的归一化比值色素指数,或者与最好的已知色素指数估算效果相当。     

连续激光辐照ZnSe/MgF2/K9滤光片的透射特性研究

分析了连续激光辐照ZnSe/MgF2/K9滤光片引起透射特性的变化。在室温条件下,用波长0.632 8μm激光作为探测光束,测量了1.06μm连续激光辐照ZnSe/MgF2/K9滤光片温升引起薄膜折射率的改变,导致探测光束通过干涉滤光片后透过率的热致非线性变化。在光斑直径0.75mm条件下,测量了不同功率激光辐照ZnSe/MgF2/K9滤光片引起温升随时间的变化。在激光功率30W,辐照时间2.52s条件下,实验观测到ZnSe/MgF2/K9滤光片薄膜破坏温度约为90℃,辐照时间10s时干涉滤光片形成的薄膜龟裂形貌。     

近地面折射率结构常数的长期测量和统计分析

统计分析了1997～2000年合肥地区一复杂地形处近地面折射率结构常数的测量数据。给出了不同下垫面、不同季节、不同高度上的统计结果。白天强弱依次为6月、5月、4月、9月、1月。白天水面上比草地上小,夜间比草地上大。不论白天还是夜晚,近地面结构常数都随高度递减,且3～10m高的结构常数递减较慢,10～15m高的结构常数递减较快。结构常数随月份的日变化与模式计算结果基本一致。     

紫外光固化阳离子复合胶粘剂的制备与表征

以三芳基六氟磷酸硫鎓盐为引发剂,钛酸四异丙酯(TIP)为无机前驱体,3,4-环氧环己基甲基3,4-环氧环己基甲酸酯为单体,制备了含TiO2纳米结构的紫外光固化阳离子复合胶粘剂。通过原子力显微镜对复合胶粘剂形貌进行表征,研究了TIP含量对胶粘剂折射率和光透过率的影响。结果表明：TiO2无机相均匀地分散在胶粘剂的聚合物基体中,平均粒径约为20 nm;随着体系中TIP质量分数的变化,复合胶粘剂折射率为1.510 3~1.540 9可调;胶粘剂的光透过率随TIP质量分数增加略有减低,但当TIP含量高达40%时,光透过率维持在90%左右。     

Synthesis of polydithiourethanes and their thermal,optical, and mechanical properties originated from monomers structure

Polyaddition of various diisothiocyanates and dithiols was achieved with triethylamine in dimethylformamide at 25 °C for 12 h under nitrogen, and then the corresponding polydithiourethanes (PDTUs) were obtained with high yield and molecular weight without depending on the monomer structures, although the dithiol monomer of the low nucleophilicity was unsuitable for polyaddition in this system. The chemical and physical properties of the obtained PDTUs such as solvent solubility, glass transition temperature, thermal stability, transparency, refractive index, and tensile strength, were analyzed in detail by gel permeation chromatography, nuclear magnetic resonance, Fourier transform infrared–attenuated total reflection, ultraviolet–visible, differential scanning calorimetry, thermogravimetric analysis, and tensile testing measurements. These results proved that PDTUs and their cast films having the aliphatic diisothiocyanate and dithiol moieties exhibited excellent chemical and physical properties compared to that of the aromatic PDTUs. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 2255–2262     

Synthesis and nanoimprinting of high refractive index and highly transparent polythioethers based on thiol-ene click chemistry

This work demonstrates the UV nanoimprinting lithography (UV-NIL) of high refractive index and highly transparent polythioethers based on thiol-ene click chemistry. Herein, 9,9-bis(3-mercaptopropylphenylether)fluorene (BMPF) is designed as a new thiol monomer with a high refractive index, high transparency, and good processability for UV-NIL. Colorless polythioethers are synthesized from BMPF and ene monomers under mild thiol-ene click reaction conditions. Excellent transmittance (96%) of 400 nm light is observed in all the polymer films and high refractive index values of 1.5972–1.6382 are attained. UV-NIL using thiol-ene photopolymerization affords polymer nanoimprinting patterns with various features on the order of 100–500 nm without any fractures. To the best of our knowledge, this is the first report on UV-NIL of high refractive index and highly transparent polymers. Through proper monomer and polymer design, novel polythioethers with suitable glass transition temperature (T _g) values are developed with high refractive index, high transparency, and good UV-NIL processability. Furthermore, UV-NIL based on thiol-ene click chemistry is accomplished at the nanoscale. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 2175–2182     

Influence of the e-beam irradiation and photo-oxidation aging on the structure and properties of LDPE-OMMT nanocomposite films

In this paper two systems, polyethylene (LDPE) and polyethylene/commercial organo-modified montmorillonite (LDPE/OMMT) nanocomposite, were subjected to e-beam irradiation at different doses and both the molecular modifications and mechanical properties have been investigated through solubility, FT-IR, calorimetric and tensile tests. Moreover, in some of the irradiated systems photo-oxidation aging was performed and its effects were studied. The results show an enhancement with irradiation of the positive effect of the nano-filler loading, related to the increase of the mechanical properties, due to the increase of the nano-filler polymer interaction.Nevertheless calorimetric and FT-IR data indicate that the well known reduction of LDPE/OMMT nanocomposite resistance to photo-oxidation ageing, with respect to LDPE, is amplified by ionizing radiation.     

Exact solution of functionally graded thick cylinder with finite length under longitudinally non-uniform pressure

Elastic analysis of a functionally graded thick-walled cylindrical pressure vessel is analytically studied in the present research. Gradation is considered for all mechanical properties along the thickness direction based on a power function. The constitutive relations are developed in the general cylindrical coordinate system for an axisymmetric pressurized cylinder. For simulation of these two deformation components, first order shear deformation theory is considered. The FG cylinder is subjected to longitudinally non-uniform pressure along the length of the cylinder. The present problem is applicable for simulation of non-uniform pressurized cylinder by fluids or gases.