An approximation algorithm for dissecting a rectangle into rectangles with specified areas

Given a rectangle R with area α and a set of n positive reals A={a₁,a₂,…,a_n} with ∑_ai∈Aa_i=α, we consider the problem of dissecting R into n rectangles r_i with area so that the set R of resulting rectangles minimizes an objective function such as the sum of the perimeters of the rectangles in R, the maximum perimeter of the rectangles in R, and the maximum aspect ratio of the rectangles in R, where we call the problems with these objective functions PERI-SUM, PERI-MAX and ASPECT-RATIO, respectively. We propose an O(nlogn) time algorithm that finds a dissection R of R that is a 1.25-approximate solution to PERI-SUM, a -approximate solution to PERI-MAX, and has an aspect ratio at most , where ρ(R) denotes the aspect ratio of R.     

RECTIFYING EFFECT OF POLYANILINE(PANI)/N-TYPE POROUS SILICONE HETEROJUNCTION*

Heterojunctions between polyaniline (PANI) and n-type porous silicon (PS), Al/PS-PANI/Au cell,were fabricated, and the rectifying parameters of this heterojunction diode were measured as a function of thepreparation conditions of PANI and PS, the electronic structure of PANI as well as cell structure. Therectifying parameters of Al/PS-PANI/Au cell were determined to be γ= 1 .8×10~1～ 1 .0×10~5 for the rectifyingratio at 3V, n = 3 ～12 for the ideal factor,j_0 = 8.0×10~(-5)～5.6×10~(-2) mA/cm~2 for the reversed saturated currentdensity, and φ_b = 0.67～ 0.83 V for the barrier height, respectively. The best rectifying heterojunction diodemade between PANI and n-type PS with higher rectifying factor (γ= 1 .0×10~5 at 3V ), output current (>1500mA/cm~2 at 3V) and lower ideal factor (n = 3.3) was obtained by preventing the oxidation of PS beforeevaporating Al electrode.     

一般寿命分布和定时截尾的Bayes变量抽样方案

林（1994）研究了指数分布和定时截尾的变量抽样方案．本文将讨论一般寿命分布和定时截尾的一次抽样方案．在多项式损失函数的假设下,我们讨论了Weibull分布、双参数指数分布和-分布三种情形,并着重讨论Weibull分布的情形．本文还提出了一个可用于近似地确定最优抽样方案的有报算法,并且进行了灵敏度分析,还同林较早的模型（1990,1994）做了比较．     

小角度纵波水浸超声检测技术在消除锻件结构盲区中的应用

航空发动机中的后轴颈锻件一般采用水浸超声纵波直入射方法检测内部缺陷。由于型面结构的问题,在锻件的直筒和锥形段连接区域存在检测盲区。该文针对某型号发动机中的后轴颈锻件,开展了水浸超声检测工艺研究,提出利用小角度纵波覆盖盲区的思路。通过对含有人工缺陷的模拟样件的检测实验,比较了水浸纵波直入射和小角度纵波斜入射两种检测方法对后轴颈连接区域的覆盖能力。结果表明,该文提出的小角度纵波方法,可以有效检测出水浸纵波直入射检测方法无法发现的人工缺陷,消除由结构引起的检测盲区,保障零件的服役安全。     

Detection of micro solder balls using active thermography and probabilistic neural network

Micro solder ball/bump has been widely used in electronic packaging. It has been challenging to inspect these structures as the solder balls/bumps are often embedded between the component and substrates, especially in flip-chip packaging. In this paper, a detection method for micro solder ball/bump based on the active thermography and the probabilistic neural network is investigated. A VH680 infrared imager is used to capture the thermal image of the test vehicle, SFA10 packages. The temperature curves are processed using moving average technique to remove the peak noise. And the principal component analysis (PCA) is adopted to reconstruct the thermal images. The missed solder balls can be recognized explicitly in the second principal component image. Probabilistic neural network (PNN) is then established to identify the defective bump intelligently. The hot spots corresponding to the solder balls are segmented from the PCA reconstructed image, and statistic parameters are calculated. To characterize the thermal properties of solder bump quantitatively, three representative features are selected and used as the input vector in PNN clustering. The results show that the actual outputs and the expected outputs are consistent in identification of the missed solder balls, and all the bumps were recognized accurately, which demonstrates the viability of the PNN in effective defect inspection in high-density microelectronic packaging.     

Structural, optical, and electrical properties of p-type NiO films and composite TiO2/NiO electrodes for solid-state dye-sensitized solar cells

p-Type nickel oxide thin films were prepared by sol-gel method, and their structural, optical and electrical properties were investigated. The Ni(OH)₂ sol was formed from nickel (II) acetate tetrahydrate, Ni(CH₃COO)₂·4H₂O, in a mixture of alcohol solution and poly(ethylene glycol), and deposited on an ITO substrate by spin coating followed by different heat treatments in air (50-800 °C). The formation and composition of NiO thin film was justified by EDX analysis. It is found that the thickness of the NiO film calcined at 450 °C for 1 h is about 120 nm with average particle size of 22 nm, and high UV transparency (∼75%) in the visible region is also observed. However, the transmittance is negligible for thin films calcined at 800 °C and below 200 °C due to larger particle size and the amorphous characteristics, respectively. Moreover, the composite electrode comprising n-type TiO₂ and p-type NiO is fabricated. The current-voltage (I-V) characteristics of the composite TiO₂/NiO electrode demonstrate significant p-type behavior by the shape of the rectifying curve in dark. The effect of calcination temperature on the rectification behavior is also discussed.     

Optimal production run time for a deteriorating production system under an extended inspection policy

A deteriorating production system is subjected to random deterioration from an in-control state to an out-of-control state with a general shift distribution. In order to reduce the defective items, part inspection policy, under which production inspections are performed only at the end of the production run, and full inspection policy are both considered in the literature. Moreover, the former dominates the latter. Since the product produced towards the end of a production cycle are more likely to be defective, it can further economize the inspection costs that they are directly reworked without inspection. In this paper, we propose an extended product inspection policy for a deteriorating production system. Product inspections are performed in the middle of a production cycle, and after the inspection, all products produced until the end of the production run are fully reworked. Based on the model, we show that there exists a production run time and a corresponding unique inspection policy such that the expected total cost per item per cycle is minimized. Finally, numerical examples are provided to illustrate our extended inspection policy, and indicate that such product inspection model will reduce the quality-related cost than part inspection does.     

基于产品质量控制的设备维修优化模型

根据产品质量和生产该产品的设备退化状态之间的相关性,设计了周期性设备检测与产品质量控制相结合的设备维修策略。该策略是在对设备进行周期性检测的基础上,利用控制图进行产品质量异常波动的检测,结合对设备退化状态的检测选择设备应采取的维修活动。根据这一设备维修策略,利用更新过程理论和统计过程控制方法,构建了基于产品质量控制的设备维修优化模型,并用遗传算法对其进行求解。通过实例仿真验证了该模型的可行性与有效性。     

服务于智能制造的智能检测技术探索与应用

为了促进工业4.0与“中国制造2025”战略在制造行业的实施,在智能制造体系中构建有效的控制层级与设备层级,促进车间状态数据与智能制造工艺流程的结合,本文提出了通过智能仪器与智能检测技术实现车间状态智能感知与工艺流程控制的方法,并探讨了智能仪器与智能检测技术在智能制造系统中新的应用模式,同时结合实际项目进行了数字化生产线改造与建设的创新实践,提出了满足智能制造要求的智能仪器与检测技术的发展方向。经项目实践验证,通过智能检测设备与智能仪器的应用,可有效促进智能制造系统中数据采集、智能感知的实现,并为整体工艺流程的智能决策提供有效的数据资源,是智能制造系统建立与完善的关键基础。