应用光纤布喇格光栅传感器监测地下管道腐蚀的新方法研究

地下管线工作环境恶劣,腐蚀是引起它破坏和失效的主要原因之一.本文提出了一种应用光纤光栅传感器监测管道腐蚀的新方法.输送石油和天然气等一些物质的管道内部存在的压力会使管道发生膨胀,进而导致管道外壁产生环向变形.假定管道为无限长,管道内部压力导致的管道外壁轴向应变可忽略不计,当管线发生腐蚀时,会导致管壁变薄,管道内部的压力又可以看作基本不变,这样就会增大管道外壁的环向应变.当管道内部压力保持恒定时,管道壁厚与应变之间存在一定的反比例关系,本文方法就是将封装好的光纤光栅传感器粘贴在管道外壁,通过监测外壁环向变形来判断管道腐蚀的情况和程度.通过理论值、模拟值和试验值三者的对比分析来说明了这种新方法是可行的,并且值得被广泛应用,为埋地管道的防灾减灾提供了一种对策.     

钢板-混凝土组合加固钢筋混凝土梁的非线性有限元分析

以10根采用钢板-混凝土组合加固技术加固的钢筋混凝土梁的试验为基础,建立了钢板-混凝土组合加固钢筋混凝土梁的非线性有限元模型.沿用了钢板-混凝土组合梁有限元分析中栓钉的荷载-滑移曲线及断裂模型,提出了新老混凝土界面的剪切-滑移模型,可以较好地模拟界面受力性能.采用有限元软件ABAQUS,模拟了一次加固、不同损伤加固及持载加固等加载情况下加固构件受力全过程和受弯破坏以及新老混凝土剥离破坏等破坏形态下加固试件的受力性能.在验证了有限元模型的准确性后,分析了钢板厚度、加固部分高度及长度等参数对加固构件承载能力及刚度的影响.最后提出了几点对钢板-混凝土组合加固RC梁的设计建议.     

Probenchemische Methode zur Bestimmung von 15N an in Gesteinen fixiertem Stickstoff

Zur Klärung geologischer Prozesse werden in zunchmendem Maße die Isotopenvariationen des Stickstoffs herangezogen. Da der größte Teil des Stickstoffs der Gesteine in gebundener Form als Ammoniumstickstoff [1–6] vorliegt, kommt der Untersuchung der Isotopenvariationen desselben eine große Bedeutung zu.     

热点应力法在高速列车设计中的应用

应力可靠性预测对高速列车车体的安全设计非常重要.本文采用国际焊接学会推荐标准预测高速列车车体关键部位应力,通过热点应力法对应力集中部位表面应力进行外推.计算结果表明通过参考点外推得到的热点应力总是明显小于有限元计算的结果,并且更接近于实验值.采用两点外推法或三点外推法计算结果的差别很小.     

Note on the Design Differentiability of the Static Response of Elastic Structures

This paper provides a new proof of design sensitivity of the static response of some typical structures. These structures (beams, plates, and plane elastic solids) have been described previously. A proof of design sensitivity of the inverse state operator was provided there, and design sensitivity of static response was derived. The proof presented here is simpler and self-contained.     

FULLY SYMBOLIC GENERATION OF COMPLEX MULTIBODY MODELS*

Abstract

In this paper, a quasistatic finite element model of a spur gear pair is developed. A node-to-target contact formulation is given, where calculations of initial gaps are based upon the actual geometry of the gear flanks rather than upon a contact node and a facet or a line segment. By using a special contact search algorithm, profile modifications and mounting errors are easily incorporated in the analysis. The problem, which also includes friction, is solved by using a nonsmooth Newton method. The static transmission error can be calculated with accuracy with a relatively small number of nodes along the gear flanks. Several examples are given in order to demonstrate the model.     

Dislocation density crystalline plasticity modeling of lath martensitic microstructures in steel alloys

A three-dimensional multiple-slip dislocation density-based crystalline formulation, specialized finite-element formulations and Voronoi tessellations adapted to martensitic orientations were used to investigate large strain inelastic deformation modes and dislocation density evolution in martensitic microstructures. The formulation is based on accounting for variant morphologies and orientations, retained austenite and initial dislocation densities that are uniquely inherent to martensitic microstructures. The effects of parent austenite orientation and retained austenite were also investigated for heterogeneous fcc/bcc crystalline structures. Furthermore, the formulation was used to investigate microstructures mapped directly from SEM/EBSD images of martensitic steel alloys. The analysis indicates that variant morphology and orientations have a direct effect on dislocation density accumulation and inelastic localization in martensitic microstructures, and that lath directions, orientations and arrangements are critical characteristics of high strength martensitic deformation and behavior.     

Bifurcation Instability of sheet metal during spring-back

In automotive and home appliance industries, there are many complex-shaped sheet metal components which need to be fabricated in multiple stamping operations. For example, the manufacturing of an outer case of washing machine consists of stamping followed by a bending operation. After the first stage of the stamping process, a large amount of spring-back takes place, and therefore, it is difficult to proceed to the next stage of the bending process. In the stamping process of that kind of sheet component with low geometric constraint, the forming area is large compared to the forming depth. Therefore, the formed part is in an unstable state and is less geometrically constrained, which causes a large amount of spring-back. To investigate this phenomenon, finite element analyses are carried out. During a spring-back analysis after forming, bifurcation takes place and the finite element solution procedure using the Newton–Raphson scheme becomes unstable. To get a stable post-bifurcation solution, a bifurcation algorithm is introduced at the bifurcation point. The deformed shapes obtained from finite element analyses are in good agreement with the experimental data. From this study, it is shown that the bifurcation behaviour enlarges the spring-back and the degree of dimensional error. To obtain additional possible post-bifurcation solutions, non-bifurcation analyses using initial guesses obtained in a modal analysis are carried. For the initial guesses, lowed four eigenmodes are utilized. Finally, the post-bifurcation behaviour and spring-back amount are investigated for various process parameters including the forming depth, punch width and corner radius.     

水下武器发射时流噪声研究

水下鱼雷武器发射噪声是潜艇的特殊噪声源。为直观详尽地描述发射系统内鱼雷出管的具体情况,本文建立了潜艇水下鱼雷安静发射普遍采用的液压平衡式发射装置内部及外部流场的有限元分析模型。基于FLUENT的动网格技术进行数值模拟,计算分析了发射过程的速度场和压力场,以及由此引起的发射流噪声特性。探讨了发射速度、发射管内外压力、潜艇航速或外部流场、水深等多种因素对鱼雷水下发射噪声的影响。