Fiber-Optic Chemical Sensor for Detection of NO2 Using Poly (3-Octylthiophene)

A fiber-optic chemical sensor (FOCS) for detection of nitrogen dioxide (NO₂) molecules is reported. The FOCS presents an optropode structure because of the transmission properties of the sensitive material. The NO₂ FOCS is activated by using the semiconductor polymer: regioregular head-to-tail poly(3-octylthiophene-2,5-diyl). The operation wavelength of the sensor is 543.5 nm such that a simple LED and detector can be used for the design of this device. The sensor response decreases after each exposure, demonstrating the reduction in sensitivity as well as irreversibility lower than 5%. However, its properties such as rapid response, high selectivity, high sensitivity (0.43 ± 0.01 muW/ppm), hygroscopic properties, and its operation at room temperature make this kind of FOCS a good alternative for NO₂ toxic gas detection.     

基于椭圆型方程的扭叶片造型方法的研究

本文以偏微分方程造型为基础,提出了一种基于椭圆型方程的扭叶片三维型面直接设计方法,详细推导了叶型曲面函数,给出了型面方程的求解及其前后缘修正。该方法具有设计叶型曲面自然光顺,设计参数少且各参数具有明显的几何意义,叶型曲面调整方便,利于采用非数值优化算法对其进行气动优化等优点。文中给出了设计实例,并通过数值实验分析了所设计叶片型面的流动特性。分析结果表明设计叶片具有良好的气动性能,同时也证明了本文提出的基于椭圆型方程的扭叶片三维型面设计方法的可靠性和实用性。     

Model spectral function and superconductivity in BaxK1−xBiO3 (x=0.5-0.7)

The Eliashberg spectral density function is constructed for the superconducting compound Ba_xK_1−xBiO₃ with x=0.5, 0.6, 0.7. The functions, besides yielding some prominent structures, show widely spreading spectra that inhibit lattice instability by yielding not too large values of λ(<1.32). The resulting spectral functions show similar shape as other results, where available, and also successfully reproduce the observed critical temperature, isotope exponent, gap ratio and several other parameters.     

Resistivity－temperature characteristics of sol gel YBa2Cu3Oy samples synthesized in flowing oxygen atmosphere

The relationship of resistivity versus synthesizing temperature of sol gel YBa_2Cu_3O_y samples was studied when prepared under flowing oxygen conditions. A set of high-temperature ρ－T curves was obtained for the whole process. After the sample finished the test measuring, its resistivity was ρ_{300}=9.83×10^{-3 }Ω·cm at room temperature. The ρ－T curve also showed that the orthorhombic－tetragonal phase transformation of sol-gel YBa_2Cu_3O_y sample occurred at 581℃ for the sample in the rising temperature process, but at 613℃ in the cooling process, lower than that of the samples made by using the conventional powder metallurgy methods.     

Compositionally modulated Fermi surfaces, structured diffuse scattering and ternary derivatives of 1T-TaS2

Ternary derivatives of 1T-TaS₂ have been synthesized and the variation in the highly structured diffuse intensity distributions characteristic of such materials carefully monitored to investigate the effect that such substitution has upon the band structures and Fermi surfaces (FSs) of the materials. Removal of d electrons via the replacement of Ta ions with lower valent transition metal ions leads to a systematic increase in the radii of the characteristic structured diffuse intensity distribution. Extended Hückel tight binding calculations of the FSs of the doped samples are carried out and used to predict possible nesting wave-vectors. The results are in reasonably good agreement with the radii of the experimentally observed diffuse intensity distributions.     

Attractors for 2D-Navier-Stokes models with delays

The existence of an attractor for a 2D-Navier-Stokes system with delay is proved. The theory of pullback attractors is successfully applied to obtain the results since the abstract functional framework considered turns out to be nonautonomous. However, on some occasions, the attractors may attract not only in the pullback sense but in the forward one as well. Also, this formulation allows to treat, in a unified way, terms containing various classes of delay features (constant, variable, distributed delays, etc.). As a consequence, some results for the autonomous model are deduced as particular cases of our general formulation.     

Estimation of growth rate in unidirectionally solidified multicrystalline silicon by the growth-induced striation method

Multicrystalline silicon was grown by unidirectional solidification method using the accelerated crucible rotation technique. The application of the accelerated crucible rotation technique in unidirectional solidification method induced growth striations across the axial direction of the grown crystal. This striation pattern was observed from carbon concentration distribution, obtained by using Fourier transform infrared spectroscopy. The generated striation pattern was found to be weak and discontinuous. Some striations were absent, probably due to back melting, caused during each crucible rotation. From the growth striations and applied time period in crucible rotation, the growth rate was estimated by using Fourier transformation analysis.     

用毛细管测量纯水表面张力系数的误差讨论

通过用毛细管测量纯水表面张力系数实验，得到管内径d与接触角θ的相对误差之间的关系曲线，由此说明实验测得的表面张力系数α和理论公式相比呈现一定的偏差，并简单地讨论了实验的理想状态与实际情况的差别．     

Equisingular Deformations of Sandwiched Singularities

We relate the equisingular deformation theory of plane curve singularities and sandwiched surface singularities. We show the existence of a smooth map between the two corresponding deformation functors and study the kernel of this map. In particular we show that the map is an isomorphism when a certain invariant is large enough.     

70K温区混合工质分凝分离循环节流制冷机实验研究

混合工质节流制冷机正在许多方面获得越来越广泛的应用。文中设计了一种新型的混合工质分凝分离循环 ,建立了实验系统 ,并在 70 K温区进行了实验。实验结果表明 ,节流制冷机可以达到 6 5 .3K的低温 ,并在 72 K温度提供 1W的制冷量 ,输入功率为 5 0 0 W。