傅里叶变换红外光谱（FTIR）非线性多点定标方法研究

给出了线性定标和非线性多点定标的具体算法,并且应用加拿大BOMEM公司的MR-154傅里叶变换红外光谱仪,液氮制冷型中红外MCT探测器测量了中国科学院上海技术物理研究所研制的HFY-300A型黑体在几种不同温度下的辐射谱,其中的一些辐射谱用于定标,用其中的一个特定温度下的辐射谱来检验定标结果。结果表明这种非线性多点定标方法非常可靠,理论辐射谱与定标后辐射谱相对偏差集中在0.2%附近,最大相对偏差仍小于0.4%。     

最小方差无失真响应浊音谱建模方法研究

讨论了在语音处理中广泛使用的线性预测模型,分析了线性预测模型在建模语音谱包络方面存在缺点,并分析了线性预测模型过高估计浊音谐波频率处能量以及随着阶数增加线性预测谱逐渐恶化的原因。在此基础上,提出了最小方差无失真响应(MVDR)建模方法,并讨论了通过Toeplitz矩阵的Cholesky分解确定MVDR滤波器系数的方法,通过与线性预测方法进行比较,发现最小方差无失真响应滤波器能提供一个更好的原始语音包络。     

Measurements in Situ and Spectral Analysis of Wind Flow Effects on Overhead Transmission Lines

In the paper an important issue of vibrations of the transmission line in real conditions was analyzed. Such research was carried out by the authors of this paper taking into account the cross-section of the cable being in use on thetransmission line. Analysis was performed for the modern ACSR high voltage transmission line with span of 213.0 m. The purpose of the investigation was to analyze the vibrations of the power transmission line in the natural environmentand compare with the results obtained in the numerical simulations. Analysis was performed for natural and wind excited vibrations. The numerical model was made using the Spectral Element Method. In the spectral model, for variousparameters of stiffness, damping and tension force, the system response was checked and compared with the results of the accelerations obtained in the situ measurements. A frequency response functions (FRF) were calculated. Thecredibility of the model was assessed through a validation process carried out by comparing graphical plots of FRF functions and numerical values expressing differences in acceleration amplitude (MSG), phase angle differences (PSG) and differences in acceleration and phase angle total (CSG) values. Particular attention was paid to the hysteretic damping analysis. Sensitivity of the wave number was performed for changing of the tension force and section area of thecable. The next aspect constituting the purpose of this paper was to present the wide possibilities of modelling and simulation of slender conductors using the Spectral Element Method. The obtained results show very good accuracy in the range of both experimental measurements as well as simulation analysis. The paper emphasizes the ease with which the sensitivity of the conductor and its response to changes in density of spectral mesh division, cable cross-section,tensile strength or material damping can be studied.     

Highly stable dielectric frequency response of chemically synthesized Mn-substituted ZnFe2O4

The tenacity of the present study was to develop a material using an economical chemical route, having balance between magnetic and dielectric order parameters for maximum transmittance of electromagnetic waves in order to use them in shielding materials. In this context, Mn-Zn ferrites were prepared using a wet chemical based sol-gel auto-combustion technique. X-ray diffraction confirmed the pure phase formation of samples, while some impurity peaks were also present for the higher value of Mn substitution. Field emission scanning electron microscopy revealed a decrease in grain size with increasing Mn substitution. While energy dispersive X-ray spectroscopy confirmed the elemental composition of pure and Mn substituted samples, the dielectric constant, dielectric loss and tangent loss were decreased with increasing frequency and increasing Mn substitution. The complex electric modulus was found to be a function of frequency and values of complex electric modulus were increased with increasing frequency and Mn substitution. The complex impedance of RC series circuit and RC parallel circuit was also decreased with increasing both the parameters while AC conductivity was increased in the series. Dielectric frequency response was also studied for the prepared samples and the best match was found with expected results. The Nyquist and Cole-Cole plots revealed the semi-conductive behavior at higher frequency and Mn substitution also yielded the same results. The relative stability of the samples to be used as dielectric materials was also studied using Bode and Nichols plots, and a comparatively high gain margin was observed, well suitable for potential applications in electromagnetic shielding.     

Simulating the dynamic behavior of planetary gearbox based on improved Hanning function

Planetary gearboxes are widely used in industrial machines. They usually work in harsh environments giving rise to damages and high maintenance costs. Condition monitoring is a key action allowing one to detect the presence of such damage ensuring healthy running conditions. The knowledge of the dynamic behavior of such a gearbox can be achieved using modeling tools as a primary step before conditioning the monitoring subject. In addition, modeling a gear set can help in the stage of design in order to optimize physical and geometric parameters of the system. Therefore, in this work, a two-dimensional lumped parameter model is adopted to build all vibration sources. The time-varying mesh stiffness is approximated as a square wave form. A novel mathematical formulation is proposed to model the amplitude modulation phenomenon due to the rotational motion of the planets around the center of the gearbox. Finally, the overall vibration signal is concluded as a summation of all vibration components influenced by the modulation function.     

Relationship of nanostructure and thermo-chemical response/thermal ablation of carbon aerogels

In this work, the interfacial mass balance relations combined with the non-parametric kinetic (NPK) analysis results were used for evaluating the thermo-chemical ablation process and oxidation mechanism of carbon aerogels with various porous structure. It was found that the two-parameter model of Nomen–Sempereis was able to describe the kinetics of the oxidation reaction and to reveal the structure-dependent contribution of two main processes with chemical and physical nature. The porosity of the carbon aerogel, rather than the other microstructural features, was realized more effective on the rate of ablation.     

Efficient removal of As(V) from simulated arsenic-contaminated wastewater via a novel metal–organic framework material: Synthesis,structure, and response surface methodology

A novel metal–organic framework material {[N(C₂H₅)₃][Zn₂(ptmda)₂(μ₂-H₂O)]·(H₂O)_0.5}_n { GUT-3 ; H₂ptmda is 4,4′-([p-tolylazanediyl]bis [methylene])dibenzoic acid} was successfully synthesized using the hydrothermal method and characterized by X-ray diffraction, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy. GUT-3 has a two-dimensional network based on dinuclear [Zn₂(ptmda)₂(μ₂-H₂O)]⁻ building units which formed an eightfold interpenetration network in GUT-3 molecules. Hirshfeld surface analysis revealed that H–H, C–H, and O–H bonds accounted for the majority of intermolecular interactions. Moreover, the interactions between GUT-3 and As(V) – the form of As(V) is AsO₄³⁻ – were analyzed in aqueous solutions in a batch system to study the effect of pH, concentration, adsorbent dose, adsorption time, adsorption temperature, and shaking speed. The kinetic and isotherm data of arsenic adsorption on GUT-3 were accurately modeled by pseudo-second-order, Langmuir (q_m = 33.91 mg/g), and Freundlich models. The Box–Behnken response surface method was used to optimize the adsorption conditions of As(V) from the simulated arsenic-contaminated wastewater. The effect of various experimental parameters and optimal experimental conditions was ascertained using the quadratic model.     

Structural response of stiffened plates in similitude under a turbulent boundary layer excitation

In structural dynamics, similitude laws usually deal with simple configurations as thin flat plates with point forces. Only recently, few papers have analyzed stiffened shells or stochastic pressure loads.This research activity extends the applicability of some similitude laws, developed for thin flat plates under a turbulent boundary layer load, to ribbed plates forced by the same wall pressure fluctuations.The work addresses the problem of designing a scaled experimental test-article and, successively, of re-modulating the measured data in order to get the structural response of an original (unscaled) configuration.Due to the complexity of the structural domain, the design of a scaled configuration leads to a distorted similitude. Then, a simple approach, to circumvent the distortion effects, is proposed.