灰铸铁表面激光熔敷层耐磨性的研究

采用激光熔敷涂料新工艺 ,以镍基焊条为熔敷材料 ,通过随机变化焊条成分 ,在熔敷层内生成 Ti C等硬质相 ,从而达到改善灰铸铁激光熔敷层组织结构和耐磨性的目的 ,考察了熔敷层中 Ti、Co和 Ni的成分变化对熔敷层耐磨性的影响 .结果表明 :以镍基焊条为熔敷材料制备的灰铸铁表面激光熔敷层具有较好的耐磨性 ;随着熔敷金属涂层内钛含量的提高 ,Ti C体积分数增大 ,熔敷层的耐磨性改善 ,而增加 Co含量可进一步提高熔敷层的耐磨性     

Open-channel turbulent flow over non-uniform gravel beds

the measurements of flow over non-uniform gravel open channel have been conducted with Laser Doppler Velocimetry (LDV). The experimental results indicate that the distribution of mean velocity agrees well with the Nikuradse's law. From the distributions of resistance coefficient, reference level and turbulence intensity, the classification of small scale roughness case is obtained.Project supported by the National Science Foundation of China     

Variation in the wave resistance of an amphibian air-cushion vehicle moving over a broken-ice field

The nonstationary rectilinear motion of an amphibian air-cushion vehicle (AACV) on a water surface covered with finely broken ice is considered for various modes of velocity variation. The influence of the water depth, flotation parameters, and mode of motion on the wave resistance of the vehicle is analyzed. Maneuvering methods for increasing or decreasing the wave resistance of AACVs are proposed. __________ Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 48, No. 1, pp. 97–102, January–February, 2007.     

???????????????????????????????

基于27种合金钢与铝合金的机械、力学性能，分析对比了3种理论估算疲劳极限方法的估 算结果，发现3种方法中只有两种方法能够比较精确地估算材料的疲劳极限; 当引 入强度系数和应变硬化指数与常规机械与力学性能的关系之后，这两种方法都可借助材料的 常规机械与力学性能估算疲劳极限，估算过程中的限制性条件``高强度钢'应予取消.     

Modelling of flow pattern in a shallow aquifer affected by reservoirs

A compartmental model is developed to estimate flow parameters of a shallow aquifer affected by water loads in surface reservoirs and to evaluate its nonsteady flow distribution. The method incorporates temporal piezometric head measurements and sampling of water for dissolved chemicals and isotopes analyses. Each compartment is governed by a set of equations describing the conservation of linear momentum and mass balance expressions for water, isotopes, and dissolved chemicals. The number of compartmental balance expressions always must be greater than that of the unknown flow parameters associated with each compartment. An optimization method is described to yield spatial distribution of aquifer storativity, transmissivity, porosity, leakage, and compliance coefficients and fluxes leaking into an aquifer's lower boundary. Future predictions of an aquifer's piezometric head distribution in a compartmental system is formulated on the basis of the estimated flow parameters and the leakage components.Compartmental modelling which incorporates concentrations of environmental tracers, may yield efficiency in computing resources and accuracy enhancement for predicting an aquifer's flow regime.     

Film thickness measurement with an ultrasonic transducer

A technique for measuring condensate film thickness using an ultrasonic transducer is described. In the experiment, the condensate film thickness with R-113 and FC-72 (a fluorinert compound developed by the 3M Company) condensing on the horizontal lower surface of a rectangular duct was measured at several locations. From the measured values a power law relation between the condensate film thickness and the axial distance from the leading edge of the condensing surface was derived by regression analysis. Assuming a linear temperature profile in the condensate film, local and average heat transfer coefficients were computed from the condensate film thickness. The average heat transfer coefficients were compared with the values obtained by measuring the heat transfer rate to the coolant. The two values were within ±12% of each other. As yet there is no satisfactory analytical model to predict the local heat transfer coefficient even in the annular condensation regime. One of the main difficulties in modeling the condensation is the lack of a suitable model to predict the interfacial shear stress. With the measurement of the film thickness it is possible to determine the interfacial shear stress. It is hoped that the shear stresses so determined will lead to the development of a satisfactory model for interfacial shear stress with condensation.     

京承高速公路新道沟连拱隧道的优化设计

本文以京承高速公路新道沟连拱隧道为实例,应用有限元数值方法对连拱隧道二次衬砌的围岩抗力、应力、变形及其稳定性等问题进行了模拟与分析。首先,基于连拱衬砌的结构型式,作者建立了该隧道的数值模型,并提出用弹性杆单元按作用力等效的原则模拟围岩抗力;根据数值模拟结果对隧道支护结构的承载能力进行了讨论,并基于规范对二次衬砌进行了结构强度校核。该研究结果为新道沟隧道支护结构设计的优化提供了科学依据。     

高温封隔器胶筒与套管接触压力的实验研究

本文利用所研制的高温封隔器测试装置,应用高温电阻应变测试技术与有限元相结合的方法,研究了油井高温封隔器胶筒与石油套管内壁接触压力大小和分布规律,为优化高温封隔器的设计,提供有价值的数据。     

水基高分子固体润滑剂摩擦系数的响应曲面分析

用正交旋转试验设计，建立了一种比多元线性回归设计更简明的水基高分子润滑剂摩擦系数的数学模型．通过摩擦系数的响应曲面分析，可以确定润滑剂配方中各组分用量变化的优化水平，用图示法分析各组分间的交互作用和它们对润滑剂质量指标的影响．此外，利用响应曲面分析法还可为研究多组分复配润滑剂的润滑性能提供数理依据     

Viscous Flow Past a Periodic Array of Spheres

Viscous flow past an infinite periodic array of rigid spheres is considered. The hydrodynamic interaction of all the particles in the array is taken into account. An analytical solution of the problem is proposed. The forces exerted by the fluid on the array particles are calculated and an expression for the velocity of fluid filtration through the array is obtained. The results are compared with the previous theoretical and experimental results.