微织构超声振动铣削系统的研究

为了在金属切削过程中在7075铝合金表面形成稳定的微织构以提高其服役性能,提出一种微织构超声铣削加工工艺。为此,该文首先基于运动合成原理获得了刀尖的运动轨迹特征和工件表面的织构形貌特征。然后,基于等效电路原理和传输矩阵法建立了超声铣削系统的频率方程,并应用牛顿迭代法获得了准确的数值解,通过有限元软件对建立的超声振动系统分别进行模态分析和谐响应分析,获得了具有微织构特征的纵扭复合超声铣削系统。最后,对加工制造出的微织构纵扭复合超声铣削系统进行振动测试、切削力测试和加工测试,结果表明:工件表面形成的"鱼鳞网纹"微观织构能够改变其润湿性能。     

一种超导重力仪磁悬浮力的等效计算

为实现超导重力仪磁悬浮力的精确计算,以GWR型超导重力仪为模型基础,采用有限元的思想,将超导球表面电流理想化为多个等高共轴电流环,计算出各个电流环与超导线圈的作用力,求和得到线圈与超导球间的磁悬浮力。利用MATLAB完成计算程序实现,通过改变下线圈电流和上、下线圈电流比,获得满足一定条件的磁悬浮力及其梯度。选取合适的模型参数,计算出线圈对质量为m=4.069 g超导球的磁悬浮力大小为:Ftotal=3.988×10^-2N,磁悬浮力梯度为:-9.699×10^-3N/m,此时悬浮力梯度合适,满足系统稳定性和灵敏度的要求。     

关于全实轴上的Lagrange插值

本文估计了以Hermite多项式的零点为节点的Lagrange插值多项式对全实轴上非一致连续函数的逼近阶.     

Finite-size scaling and the renormalization group

Renormalization group calculations ind = 4 andd = 4 – are performed for a system of finite size. A form of mean-field theory is used which yields a rounded transition for a finite system, and this allows a sensible expansion in fluctuations. A combination of Ewald and Poisson sum techniques is used to produce explicit numerical results for the specific heat ind = 4 which, with the setting of two nonuniversal metrical factors and the fourth-order coupling constant may be compared with simulations. The numerical visibility of logarithmic corrections is investigated. The universal scaling function for the specific heat to relativeO() is also evaluated numerically.     

棱镜自重变形对波面影响的研究

采用有限元方法分析了单棱镜在重力作用下三个典型位置的表面变形,对棱镜表面Φ425mm通光孔径轴向变形量进行Zernike多项式拟合,画出了相应的波差图,并确定设计方案.进一步选择Φ360 mm口径光束对双棱镜在几种典型相对位置下进行光线采样、追迹,计算得到不同情况下由于双棱镜自重变形引起的总波差.     

SIMPLE TECHNIQUES FOR DETERMINING THE SMALL-SIGNAL EQUIVALENT CIRCUIT OF MESFET’s

Simple techniques for determining the broadband small signal equivalent circuit (SSEC) of MESFETs are presented in this paper. The intrinsic elements are calculated using two-dimensional method from the Y parameters, which are obtained from the Fourier analysis of the device transient response to voltage-step perturbations at the drain and gate electrodes. Whereas, the parasitic external elements are determined by simple approximations used in transmission line modeling. In addition, a new technique is also proposed to determine the source and drain series resistances. A comparison of the SSEC of three different MESFETs technologies shows that the MESFETs on GaN and 4H-SiC are suitable for high power applications. The method used to determine the intrinsic elements is validated with simulated data obtained by Monte Carlo method.     

Laser soldering of flip-chips

A novel process for laser soldering of flip-chips on transparent printed circuit board assemblies is presented. The experiments were carried out on silver test patterns printed on glass wafers using a roller-type gravure offset printing method. The contact pads, where the bumps of the flip-chips are positioned, were covered with a thin layer of additional solder paste. The aligned samples (solder pad—solder paste—chip bump) were illuminated through the glass substrate using an Ar⁺ laser beam (, , at 1/e) to heat the printed pad and melt the solder paste, thus forming a joint between the printed pad and the chip bump. The heat-affected zone was modeled using computer-assisted finite element method. The solder joint cross-sections were analyzed using optical and electron microscopy as well as energy dispersive X-ray element analyses. The laser-soldered joints were of good mechanical and electrical quality and the process proved to be suitable for manufacturing customized circuit prototypes.     

Factorizing multivariate time series operators

Motivated by problems occurring in the empirical identification and modelling of a n-dimensional ARMA time series X(t) we study the possibility of obtaining a factorization (I + a₁B + … + a_pB^p) X(t) = [Π_i=1^p (I ? α_iB)] X(t), where B is the backward shift operator. Using a result in [3] we conclude that as in the univariate case such a factorization always exists, but unlike the univariate case in general the factorization is not unique for given a₁, a₂,…, a_p. In fact the number of possibilities is limited upwards by $\text{(np)!}\text{(n!)}{}^{\mathrm{p}}$, there being cases, however, where this maximum is not reached. Implications for the existence and possible use of transformations which removes nonstationarity (or almost nonstationarity) of X(t) are mentioned.     

Rank-based deactivation model for networks with age

We study the impact of age on network evolution which couples addition of new nodes and deactivation of old ones. During evolution, each node experiences two stages: active and inactive. The transition from the active state to the inactive one is based on the rank of the node. In this paper, we adopt age as a criterion of ranking, and propose two deactivation models that generalize previous research. In model A, the older active node possesses the higher rank, whereas in model B, the younger active node takes the higher rank. We make a comparative study between the two models through the node-degree distribution.     

不同排列下高温超导带材交流损耗的仿真计算

交流损耗的数值计算对于高温超导带材具有重要的现实意义。应用有限元软件模拟仿真超导体部分计算求出不同排列下的交流损耗,与实验结果以及Norris公式的计算结果相比较,得到的仿真结果符合较好。结果说明圆筒形的排列能够有效地减少交流损耗。