改性CF与EVA复合材料的PTC行为研究

试图通过增强EVA与CF之间的相互作用来消除NTC现象. 由于CF表面光滑, 惰性大, 将CF用KMnO4表面氧化后与具有活性官能团的EVA熔融共混, 得到EVA-改性CF复合物.     

Conducting composites from EPDM–EVA blends

The effect of ethylidene norbornene (ENB) content of ethylene propylene aiene rubber (EPDM) and vinyl acetate (VA) content of ethylene vinyl acetate copolymer (EVA), as well as the blending sequence, on the conductivity of composites based on EPDM–EVA–carbon black have been studied. Black master batches show a lower extent of cure than the preblended system followed by black addition. EPDM having a high ENB content shows higher conductivity under ambient conditions. Preblended systems give rise to higher conductivity in the case of low-ENB content EPDM. But for high-ENB content EPDM, the blending of black master batches imparts high conductivity. Two types of conduction are observed in this case and the transition temperature depends on the VA content of EVA. It appears that there exists a correlation between activation energy of curing and that of conduction.     

The reactive compatibilization of NBR/EVA blends with oxazoline-modified nitrile rubber

The reactive compatibilization of ethylene-vinyl acetate copolymer (EVA)/nitrile rubber (NBR) blends has been performed using partially hydrolyzed EVA (EVALVA) in combination with oxazoline-functionalized NBR (NBROX). The synthesis of the NBROX has been performed in solution. The presence of 5 wt% of EVALVA in combination with 2.5 wt% of NBROX resulted in a substantial improvement of tensile strength of NBR/EVA (50:50 wt%) vulcanized blends, with a little increase of the elongation at break. The morphologies of these blends were examined by the scanning electron microscopy. A finer morphology has been observed in vulcanized and non-vulcanized blends, compatibilized with the co-reactive EVALVA/NBROX copolymers. Blends of NBROX/EVALVA (50:50 wt%) resulted in insoluble material, constituted by both components, as indicated by Fourier transform infrared analysis. This result indicates the reaction of the co-reactive groups (hydroxyl and oxazoline) during blending.     

Electron beam crosslinking of poly(ethylene-co-vinyl acetate)/clay nanocomposites

Effect of electron beam irradiation on the thermal and mechanical properties of poly(ethylene-co-vinyl acetate) (EVA)/clay nanocomposites prepared by melt blending method has been investigated. The hot set test results show that elongation at high temperature under static load decreased with the increase of irradiation dose. The tensile modulus increased continuously with increasing dose. While the tensile strength increased up to 100 kGy, it decreased with further increase in dose. The elongation at break decreased continuously with increasing dose. Thermogravimetric analysis showed that thermal stability of the EVA/clay nanocomposites improved with increasing dose. The improvement in the mechanical and thermal properties is attributed to the formation of radiation-induced crosslinking as evidenced by the gel content results.     

Porcelain tile surface modification with isocyanate coupling agent: interactions between EVA modified mortar and silane improving adherence

Adhesion between tiles and mortar is of paramount importance to the overall stability of ceramic tile systems. The interfaces between ceramic tiles and polymer‐modified Portland cement mortar are derived from several physical and chemical phenomena that take place during their formation. From the chemical perspective, weak forces are expected to occur preferably at the tiles and polymer‐modified Portland cement mortar interfaces. Therefore, the purpose of this study was to promote a new chemical functionalization of ceramic tile surfaces by modifying with isocyanate‐trialkoxysilane coupling agent in order to enhance the interfacial adhesion with poly (ethylene‐co‐vinyl acetate), EVA, polymer‐modified mortar. Pull‐off tests and Fourier Transformed Infrared Spectroscopy (FTIR), using the Attenuated Total Reflectance method, were carried out in order to characterize the system. The bond strength results have provided evidence toward improvements in adherence at the tile–polymer modified mortar interface, thus reflecting the development of urethane linkages between silane and EVA polymer, as detected by FTIR. Copyright © 2010 John Wiley & Sons, Ltd.     

Impact behavior of sugarcane bagasse waste–EVA composites

The impact performance of chopped bagasse–EVA matrix composites is evaluated and compared with the behavior of bagasse filled PP and PE matrix composites and wood-based materials. The volume fraction and size of the chopped bagasse used as filler was varied. The experimental results show that the incorporation of bagasse strongly reduces the deformation capacity of EVA polymer. The reduction of the deformation capacity of the composites was also inferred by solid-state NMR relaxation analysis. The impact strength was independent of the bagasse size, but varied with the volume fraction. As a function of the volume fraction it was shown that the mechanical performance of bagasse–EVA composites could be tailored to reproduce the behavior of wood-based particle boards.     

Nonisothermal crystallisation, melting behavior and wide angle X-ray scattering investigations on linear low density polyethylene (LLDPE)/ethylene vinyl acetate (EVA) blends: effects of compatibilisation and dynamic crosslinking

Crystallisation studies on LLDPE/EVA blends and the individual components were performed with wide angle X-ray scattering (WAXS) technique and differential scanning calorimetry (DSC) DSC was used to characterise the quiescent crystallisation behavior. The heat of fusion and crystallinity of the blends were reduced by the addition of EVA. The experimental and theoretical values of crystallinity of the blends were found to be mutually agreeing. Crystallisation of LLDPE remains impeded to some extent due to the presence of amorphous EVA. Compatibilisation does not affect crystallinity whereas crosslinking decreases crystallinity. Crosslinking and compatibilisation make no significant change in the melting temperature of the blends. X-ray diffraction studies were carried out on un-crosslinked and crosslinked LLDPE/EVA blends with a view to study the effect of blend composition and crosslinking on crystallinity and lattice distance. Studies revealed that LLDPE and EVA have orthorhombic unit cell. Blending with EVA did not affect the crystalline structure of LLDPE, but the crystallinity decreases with EVA content. At low concentrations of EVA the lattice parameters remain unchanged. Above 30% EVA content however, a linear increase has been observed. Dicumyl peroxide (DCP) crosslinked samples show considerable shift of (1 1 0), (2 0 0) and (0 2 0) crystalline peaks towards lower 2θ values indicating an increase of unit cell parameters of the orthorhombic unit cell of polyethylene. At lower EVA-concentrations (<50%) the crystalline structure remains unchanged. For EVA-contents of more than 70% however, increasing DCP-content reduces the crystallinity of the blends and increases the lattice distance. This indicates that DCP-crosslinking is more effective in EVA phase than in the LLDPE phase.     

Ethylene/vinyl acetate copolymer/clay nanocomposites

This article highlights the history, synthetic routes, material properties, and scope of ethylene/vinyl acetate copolymer (EVA)/clay nanocomposites. These nanocomposites of EVAs are achieved with either unmodified or organomodified layered silicates with different methods. The structures of the resulting polymer/inorganic nanocomposites have been characterized with X‐ray diffraction, scanning electron microscopy, and transmission electron microscopy. The addition of a small amount of clay, typically less than 8 wt %, to the polymer matrix unusually promotes the material properties, such as the mechanical, thermal, and swelling properties, and increases the flame retardancy of these hybrids. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 471–480, 2006     

Electron-beam irradiation effects on poly(ethylene-co-vinyl acetate) polymer

Poly(ethylene-co-vinyl acetate) (EVA) films were irradiated with a 1.2 MeV electron beam at varied doses over the range 0–270 kGy in order to investigate the modifications induced in its optical, electrical and thermal properties. It was observed that optical band gap and activation energy of EVA films decreased upon electron irradiation, whereas the transition dipole moment, oscillator strength and number of carbon atoms per cluster were found to increase upon irradiation. Further, the dielectric constant, the dielectric loss, and the ac conductivity of EVA films were found to increase with an increase in the dose of electron radiation. The result further showed that the thermal stability of EVA film samples increased upon electron irradiation.     

Selective distribution,reinforcement, and toughening roles of MWCNTs in immiscible polypropylene/ethylene‐co‐vinyl acetate blends

Polypropylene/ethylene‐co‐vinyl acetate (PP/EVA) nanocomposites with functionalized multiwalled carbon nanotubes (FMWCNTs) have been prepared. The dissolution experiment, transmission electronic microscope, and scanning electronic microscope characterizations prove that, in the nanocomposites with sea–island morphology, although some FMWCNTs are observed in both PP and EVA phases, most of FMWCNTs distribute at the interface; however, in the nanocomposites with cocontinuous morphology, FMWCNTs mainly distribute in EVA phase. Further results based on (differential scanning calorimetry) measurements show that the different dispersion states of FMWCNTs, which are resulted by the different melt blending sequences, result in the different crystallization behaviors of PP matrix. The mechanical measurements show that FMWCNTs exhibit apparent reinforcement and toughening effects for immiscible PP/EVA blends, and such effects are greatly dependent upon the blending sequences. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1882–1892, 2010