THE PREPARATION AND STUDY ON THE NANO-TiO2/SILK FIBROIN COMPOSITE FILMS BY THE SOL-GEL METHOD

Based on the sol-gel technique using butyl titanate as oxide precursor, the regenerated SF (silk fibroin)/nano-TiO2 composite films were synthesized. Different amounts of butyl titanate to SF were used to verify this effect on the characteristics of the formed materials. Samples were characterized by thermogravimetric analysis, X-ray diffractometry, UV, AFM and FT-IR spectroscopy.The experimental results reveal that, compared to the pure silk fibroin films, the mechanical strength of these regenerated SF/nano-TiO2 composite films were increased and the dissolubility in water of SF/nano-TiO2 composite films in aqueous solution were decreased. The diameter of nano-TiO2 particle films was about 80nm through UV and AFM. The nano-TiO2 particles were well dispersed in the regenerated silk fibroin. It was found that the crystal structures of the composite films were transited from typical Silk Ⅰ to typical Silk Ⅱ by the XRD and FTIR. Furthermore, the crystallinity of the composite films was obviously improved. Through the TGA, it was demonstrated that the heat transition temperature of composite films was also enhanced.     

热散焦效应对甲烷后向受激喇曼散射的影响

The conversion efficiency of stimulated Raman scattering (SRS) in CH4 is studied by using a single longitudinal mode second-harmonic Nd:YAG laser (532 nm, linewidth 0.003 cm-1, pulse-width (FWHM) 6.5 ns).Due to the heat release from vibrationally excited particles, SRS processes often suffer from the thermal defocusing effect (TDE). In view of 6.5 ns laser pulse width is much shorter than the vibrational relaxation time of CH4 molecules, TDE can only affect the SRS processes afterwards. In the cases of low laser repetition, TDE will be not serious, because it will be removed by the thermal diffusion in Raman medium before the next pulse arrives. At the laser repetition rate 2 Hz, CH4 pressure 1.1 MPa and pump laser energy 95 m J, the quantum conversion efficiency of backward first-Stokes (BS1) has attained 73%. This represents the highest first-stokes conversion efficiency in CH4. Furthermore, due to the relaxation oscillation, the BS1pulses are narrowed to about 1.2 ns. As a result, the BS1 peak power turns out to be 2.7 times that of the pump. Its beam quality is also much better and is only slightly affected by TDE. This reason is that BS1 represents a wave-front-reversed replica of the pump beam, which can compensate the thermal distortions in Raman amplify process. Under the same conditions, but pump laser repetition rate as 10 Hz, the conversion efficiency of BS1 goes down to 36% due to TDE. From this study, we expect that a well-behaved 630 nm Raman laser may be designed by using a closed CH4/He circulating-cooling system, which may have some important applications.     

低温溶剂热法制备5V级性能优异的LiCr_(0.2)Ni_(0.4)Mn_(1.4)O_4正极材料(英文)

通过低温溶剂热的方法成功制备出了LiCr0.2Ni0.4Mn1.4O4尖晶石正极材料。通过此法,溶液的饱和蒸汽压急剧降低且在室温(25℃)下即可沸腾。所有的金属离子可在随后的热聚合过程中均匀分散且煅烧后所得材料无杂质相生成。采用了热重分析,X射线衍射,扫描电镜、循环伏安,交流阻抗等测试手段对材料进行了表征。结果表明:此法所得材料含有Mn3+,为Fd3m晶型,且其形貌规则、粒度分布均一。1C和10C下放电容量为140.5和121.0 mAh·g-1,10C下100次循环容量保持率高达96.9%。其优异的电化学性能可归因于均相的前驱体制备过程,高结晶度且无杂相生成,以及较高的锂离子扩散系数诸因素的共同作用。     

神府煤与稻杆共热溶研究

研究了神府煤与稻杆在1-甲基萘溶剂中不同温度下的共热溶行为。相对神府煤,稻杆单独热溶时具有更高的热溶率,表明其具有较好的热溶活性。但稻杆的热溶过程中产生大量的挥发性气体,导致其热溶率和热溶物产率之间的较大差异。神府煤单独热溶时,其热溶率与热溶物产率之间的差异相对较小。神府煤与稻杆的共热溶表明,两者之间存在协同效应,并且该协同效应受温度的影响显著。在热溶温度为320~340 ℃时,对热溶物产率而言具有正的协同效应,也即其热溶物产率的实验值大于通过神府煤与稻杆单独热溶时热溶物产率经质量加权平均计算得到的理论值。在研究的热溶温度范围内,共热溶的热溶率实验值均低于质量加权平均的理论计算值。相对于理论计算值,在320 ℃时热溶物产率的实验值增加达到最大,为7.9%。此外,通过对热溶物的性质表征,还进一步探讨了共热溶过程中的协同作用机理。     

Oxidative coupling of methane in a fixed bed reactor over perovskite catalyst： A simulation study using experimental kinetic model

The oxidative coupling of methane （OCM） to ethylene over a perovskite titanate catalyst in a fixed bed reactor was studied experimentally and numerically. The two-dimensional steady state model accounted for separate energy equations for the gas and solid phases coupled with an experimental kinetic model. A lumped kinetic model containing four main species CH4, O2, COx （CO2, CO）, and C2 （C2H4 and C2H6） was used with a plug flow reactor model as well. The results from the model agreed with the experimental data. The model was used to analyze the influence of temperature and feed gas composition on the conversion and selectivity of the reactor performance. The analytical results indicate that the conversion decreases, whereas, C2 selectivity increases by increasing gas hourly space velocity （GHSV） and the methane conversion also decreases by increasing the methane to oxygen ratio.     

镉配位聚合物的合成及其染料吸附性能研究综合实验*

介绍了一个研究型综合实验,涉及镉配位聚合物的合成及其染料吸附性能研究。该实验使用常见有机配体丁二酸、1,4-二(1-咪唑)苯与硝酸镉四水合物,在溶剂热条件下进行反应得到一例镉配位聚合物。利用X射线单晶衍射、X射线粉末衍射、热重分析、红外光谱对配位聚合物进行结构表征,并对其染料吸附性能进行研究。该实验将科学研究热点融入基础实验教学,既巩固了学生的基础理论知识,提高了实验技能,又拓展了学生的科学视野,加强了他们独立分析问题、解决问题的能力,有利于培养学生的创新精神和实践能力。     

化学能转化成电能的实验设计

以常见的铜锌原电池反应为例,设计了一组对比实验装置,即化学反应装置与原电池装置。以化学反应装置中的能量变化为依据,展示了化学反应中释放出的能量具体形式为“热”与“功”;通过与原电池装置的比较,证明原电池实验装置中的“热”转化为了电能。     

热裂解气相色谱质谱法分析聚合物中红磷

采用单击热裂解(PY)模式和逸出气体分析(EGA)程序升温两种热裂解模式对红磷样品进行定性分析,利用气相色谱分离技术对红磷进行分离,根据红磷的特征质谱31,62,93,124及特征丰度比,质谱法分析不同材料中的红磷含量。单击热裂解模式下,材质和添加剂有可能对红磷造成干扰,改进后的EGA热裂解模式能排除红磷检测中材质和添加剂的干扰,并采用改进后的EGA裂解程序测定自制阳性样品中红磷的含量。结果表明:通过优化裂解温度和气相色谱条件可以有效改善红磷的分析结果,红磷质量浓度在100~500 mg/kg范围内具有良好线性,加标回收率在90.7%~97.7%,相对标准偏差(RSD)为1.6%~2.3%,定量限为81.27 mg/kg。     

电感耦合等离子体原子发射光谱法测定铜矿中砷的含量

近年来,对于铜精矿中有害杂质元素的要求越来越严格,其中杂质元素砷的测定是进出口铜精矿的常规检定项目之一[1-2]。铜矿样中砷的含量直接影响到电解铜的质量,因此准确、快速测定铜矿样中砷的含量就显得特别重要[3]。     

涡旋提取-石墨炉原子吸收光谱法测定土壤中有效态镉

土壤作为农业生产的重要载体,是保障农产品质量安全的关键源头。近年来,随着经济的快速发展,土壤中重金属污染问题日益凸显,已成为世界性的重大环境问题之一。目前针对土壤中重金属的调查分析大多处于总量水平,这并不能全面地评价重金属的生态风险,因为土壤-重金属-生物体之间存在复杂的动态相互作用,土壤中只有部分重金属能被生物体吸收,这部分能被生物体吸收利用的元素以特定的形态存在,这种特定的形态被称之为有效态。土壤中重金属能否被植物吸收主要取决于该元素的有效态[1],因此土壤中重金属有效态含量的测定,对评价和控制其生物毒害作用具有更实际的意义。镉是生物蓄积性强、具有"三致"作用的剧毒元素,会通过食物链富集到人体,从而对人体健康造成危害[2]。目前我国暂未制定土壤中有效态镉的限量标准,关于土壤中有效态镉含量测定方法的研究也较少[3-5],国家标准方法 GB/T 23739-2009(S)《土壤质量有效态铅和镉的测定原子吸收法》前处理采用振荡器低效提取,提取时间长,试剂用量大,提取液根据含量高低选用火焰原子吸收光谱仪或者石墨炉原子吸收光谱仪,操作较繁琐,无法满足批量样品快速分析的要求。文献[3-4]采用超声提取-电感耦合等离子体质谱法,前处理操作简单,但仪器成本较高,方法应用的推广有一定的局限性,且由于土壤样品基体复杂,容易堵塞雾化器导致仪器故障。