具有变时滞和马尔可夫切换的随机递归神经网络的弱收敛(英文)

本文研究了具有变时滞和马尔可夫切换的随机递归神经网络的弱收敛,通过运用Lyapunov函数、随机分析技巧和推广了的Halanay不等式,得到了上述模型为弱收敛的充分性条件,并且我们揭示了对上述递归神经网络模型所确定的segment过程的转移概率的极限分布是此模型的解过程的唯一的遍历不变概率测度.此外,我们还给出了例子和数值模拟来说明我们结论的正确性.     

激光干涉光路偏振移相误差分析

成像光谱仪能够获得目标表面图像特征和频谱特性,提高目标识别分析能力,在军用、民用领域有广泛应用。红外焦平面阵列的等光程间隔采样特性是限制光谱仪分辨率的重要因素。激光干涉光路与成像系统同光路,为红外焦平面阵列提供采样触发信号,实现等光程差采样。通过搭建激光偏振移相干涉光路,对干涉信号幅值和相位差进行理论分析和实际验证,最终调试得到两路正交干涉信号,相位差范围为84.6°~93°,反射透射光强幅值比例小于1∶1.05。实验结果表明,干涉光路中1/8波片角度、偏振分光片角度、探测器位置等参数是影响干涉信号幅值和相位差的重要因素。     

低温热分析标准物质的研制

研制了两种0~100℃热分析标准物质,分别为金属镓和水杨酸苯酯标准物质。研制的标准物质具有良好的均匀性和稳定性,采用与NIST,LGC相应标准物质比较的方法定值。NIST为SRM 2234镓,其定值采用288.6~314.35 K范围内的绝热热量计测得温度及热量值;LGC用绝热法为水杨酸苯酯的熔化温度和熔化热定值,两种方法都可以直接溯源至SI单位。对定值结果的不确定度进行了分析和评定。镓和水杨酸苯酯标准物质的熔化温度分别为(29.77±0.20)℃(k=2),(41.81±0.34)℃(k=2);熔化热分别为(80.52±0.48)J/g(k=2),(88.94±0.62)J/g(k=2)。研制的两种标准物质满足国家标准物质的技术要求,申报已获批准。     

Vulcanization kinetics of graphene/styrene butadiene rubber nanocomposites

This paper presents the influence of graphene on the vulcanization kinetics of styrene butadiene rubber （SBR） with dicumyl peroxide. A curemeter and a differential scanning calorimeter were used to investigate the cure kinetics, from which the kinetic parameters and apparent activation energy were obtained. It turns out that with increasing graphene loading, the induction period of the vulcanization process of SBR is remarkably reduced at low graphene loading and then levels off; on the other hand, the optimum cure time shows a monotonous decrease. As a result, the vulcanization rate is suppressed at first and then accelerated, and the corresponding activation energy increases slightly at first and then decreases. Upon adding graphene, the crosslinking density of the nanocomposites increases, because graphene takes part in the vulcanization process.     

Electrospinning of nylon-6,6 solutions into nanofibers: Rheology and morphology relationships

The relationship between the rheological properties of nylon-6,6 solutions and the morphology of their electrospun nanofibers was established. The viscosity of nylon-6,6 in formic acid(90%) was measured in the concentration range of 5 wt%-25 wt% using a programmable viscometer. Electrospinning of nylon-6,6 solutions was carried out under controlled parameters. The chemical structure, morphology and thermal properties of the obtained nanofibers were investigated using Fourier transform infrared spectroscopy(FTIR), scanning electron microscopy(SEM) and differential scanning calorimetry(DSC), respectively. Entanglement concentration(ce) was found to be 15 wt% and a power law relationship between specific viscosity and solution concentration was observed with exponents of 2.0 and 3.3 for semi-dilute unentangled(c ce) and semi-dilute entangled(c ce) regimes, respectively. The diameter and uniformity of the nanofibers were found to be dependent on the viscosity. Moreover, the average diameter of electrospun nanofibers was found to be dependent on zero shear rate viscosity and normalized concentration(c/ce) in a power law relationship with exponents of 0.298 and 0.816, respectively. For nylon-6,6 solutions, the entanglement concentration(ce = 15 wt%) provides the threshold viscosity required for the formation of a stable polymeric jet during electrospinning and producing uniform beadless fibers. For concentrations less than ce, beaded fibers with some irregularities are formed. DSC analysis showed an increase in crystallinity of all electrospun samples compared to original polymer. Furthermore, Based on FTIR spectroscopy, α phase is dominant in electrospun nanofibers and minor amount of β and γ phases is also available.     

Microstructure characterization of short-chain branching polyethylene with differential scanning calorimetry and successive selfnucleation/annealing thermal fractionation

A series of the copolymers of ethylene with 1-hexene(M1–M9) synthesized by metallocene catalyst Et[Ind]2ZrCl2/MAO was studied by differential scanning calorimetry and successive self-nucleation and annealing(SSA) thermal fractionation. The distribution of methylene sequence length(MSL) in the different copolymers was determined using the SSA method. The comonomer contents of samples M4 and M5 are 2.04 mol% and 2.78 mol%, respectively. Both M4 and M5 have low comonomer content and their MSL distribution profiles exhibit a monotonous increase trend with their MSL. The longest MSL of M5 is 167, and its corresponding molar percent is 43.95%, which is higher than that of M4. Moreover, the melting temperature(Tm) of M5 is also higher than that of M4. The comonomer contents of samples M7, M8, and M9 are 8.73 mol%, 14.18 mol% and 15.05 mol%, respectively. M7, M8, and M9 have high comonomer contents, and their MSL distribution profiles display unimodality. M7 has a lower peak value of 33 and a narrow MSL distribution, resulting in a Tm lower than that of M8 and M9. The MSL and its distribution are also key points that influence the melting behavior of copolymers. Sometimes, MSL and its distribution of copolymers have a greater impact on it than the total comonomer contents, which is different from traditional views.     

多层绝热材料规模化干燥处理时温度场的测试与分析

对大批量处理多层绝热材料的大型专用干燥箱满负荷运行时工作区域的温度场进行测试,通过温度分布和温度场均匀性的分析,得出了最高温度发生点的位置与成因以及影响温度场均匀性的主要因素,并对温度的控制方法、多层材料的布置方案和干燥设备的改进提出了建议。     

氨基甲酸酯型α-猪去氧胆酸分子钳对分子的识别性能研究

用差紫外光谱滴定法考察了新型猪去氧胆酸分子钳1~6对苯胺、对甲氧基苯胺、对硝基苯胺等中性分子的识别性能,测定了主客体间的结合常数(Ka)和自由能变化(△G°)。结果表明,分子钳主体对所考察的客体分子显示良好的识别作用,主客体间形成1∶1型超分子配合物,最大结合常数可达3123.46L.mol-1,识别作用的主要推动力为氢键,范德华力等的协同作用。讨论了主体与客体的识别模式以及客体间形状、大小匹配和几何互补等因素对形成超分子配合物的影响,并利用核磁共振氢谱与计算分子模拟作为辅助手段对实验结果与现象进行了解释。     

光刻机投影物镜的像差原位检测新技术

提出了一种新的光刻机投影物镜像差原位检测(AMF)技术。详细分析了该技术利用特殊测试标记检测投影物镜球差、像散、彗差的基本原理,论述了该技术利用对准位置坐标计算像差引起的成像位置偏移量的方法。实验结果表明AMF技术可实现球差、彗差、像散等像差参量的精确测量。AMF技术考虑了光刻胶等工艺因素对像差引起的成像位置偏移量的影响,有效避免了目前基于硅片曝光方式的彗差原位检测技术对离焦量、像面倾斜等像质参量限制的依赖。