用于紫外光谱水质分析的Boosting-偏最小二乘法

为提高水质参数总有机碳(TOC)的紫外吸收光谱分析的预测精度,提出一种基于Boosting理论的迭代式回归建模算法,并根据统计学习理论提出一种新的迭代停止判据,可有效防止过拟合,显著提高模型预测精度。为评估所提算法的性能,分别采用本算法和3种常用的光谱分析方法,即偏最小二乘、主成分回归和人工神经网络,对自行研制的紫外光谱水质分析仪实测的一组数据进行了建模和预测。计算结果表明:相对于其他3种方法,本算法具有生成的模型预测精度高的显著优势。     

高分辨等离子体质谱法直接测定高纯镓中的痕量元素

建立高分辨电感耦合等离子体质谱法(HR-ICP-MS)测定高纯镓样品中Be、Mg、A l、S i、Ti、V、Cr、Mn、Fe、Co、N i、Cu、Zn、Ge、As、Mo、Ag、Cd、In、Sb、Ba、Pb、B i等痕量元素的方法。样品用HNO3 HC l经微波消解后,试液直接进样用HR-ICP-MS法同时测定上述元素,在高分辨质谱测量模式下避免了大量的质谱干扰,详细地研究了HC l和高纯镓所产生的基体效应,以Sc、Rh、Tl作为内标元素校正了基体效应,讨论和确定了实验的最佳测定条件。结果表明,23种痕量元素的检出限在0.001~0.21μg/L之间;回收率在89.8%~111.6%之间,相对标准偏差(RSD)小于3.3%。     

电吸附技术的应用与研究

本文综述了活性炭、活性炭纤维、炭气凝胶及活性氧化铝等材料的电吸附/脱附技术的研究进展。主要介绍了其在去除水中无机和有机污染物方面的应用,并对今后的研究方向提出了建议。     

聚铝碳硅烷纤维预氧化过程组成结构演变的研究

采用热重-差热分析、元素分析、扫描电子显微镜、凝胶渗透色谱、红外光谱和核磁共振等手段, 研究了聚铝碳硅烷(PACS)纤维预氧化过程中组成、结构演变的规律和反应机理. 结果表明, 空气中PACS纤维从210 ℃左右开始与氧发生放热反应; 随着预氧化温度的升高, 纤维的氧含量逐渐增加, 凝胶含量在氧增重为6～8 wt%时急剧增加, 纤维表面出现细小的微裂纹. 预氧化初期, 主要是Si—H键与氧的反应, 生成Si—O—Si键, 纤维的数均分子量急剧增加, 形成交联结构; 预氧化中期, Si—H键继续反应, Si—O—Si结构明显增多, 同时Si—CH₃和Si—H与氧反应, 生成少量的Si—O—C结构; 预氧化后期, 纤维完全交联, 纤维中存在SiC₄, SiC₃H, Si—O—Si和少量的Si—O—C结构.     

On interrelation between the internal pressure and the cohesion energy density

The question about the definition of the “internal pressure” concept is being discussed. It is shown that the previously found differential relation between the cohesion energy density and the internal pressure is one of the examples of an absolutely general interrelation between definitely connected differential functions. It is ascertained that the ratio (the internal pressure divided by the cohesion energy density) is a structuresensitive parameter inherent to the calorific (thermal) equation of a liquid state.     

TCF selenium preconcentration in geological materials for determination at sub-mugg(-1) with INAA (Se/TCF-INAA)

In geological samples, Se concentration ranges from 1 × 10⁻⁹ g g⁻¹ up to 1 × 10⁻³ g g⁻¹. The analytical difficulty at low concentration (<1 μg g⁻¹), is one of the main reasons why the geological cycle of Se is poorly known. The analytical method that consisted of preconcentration of Se with thiol cotton fiber (TCF) followed by graphite furnace atomic absorption spectrometry (GFAAS) has been modified by finishing with instrumental neutron activation analysis (INAA). The modified technique involves sample dissolution (HF-HNO₃-H₂O₂) and evaporation to dryness at low temperature (55-60 °C) to avoid selenium volatilization. Se^VI is converted to Se^IV by adding 6 M HCl to the dry residuum and the solution is then heated in a covered boiling bath (95-100 °C). The solution is diluted to obtain 0.6 M HCl and then collected on TCF. The TCF is placed in a polyethylene vial for irradiation in the SLOWPOKE II reactor (Montréal) for 30 s at a neutron flux of 10¹⁵ m⁻² s⁻¹. The 162 keV peak of ^77mSe (half-life 17.36 s) is read for 20 s after a decay of 7 s. The amount of sample to be dissolved is controlled by two competing effects. To obtain low detection limits, a larger amount of sample should be dissolved. On the other hand, the TCF could become saturated with chalcophile elements when large sample is used. Sulfur is a good indicator of the amount of Se and chalcophile elements present. In S poor sample (<100 μg g⁻¹) 3.0 g of sample was used and the L_D was ∼2 ng g⁻¹. In S high samples (>1.5% S) 0.05 g of sample was used and the L_D was ∼120 ng g⁻¹. The present work also includes suggested Se concentration for eight international geological reference materials (IGRM) that compare favorably with literature values.     

Electrospinning of nylon-6,66,1010 terpolymer

Ultrafine nylon fibers were prepared by electrospinning of nylon-6,66,1010 terpolymer solution in 2,2,2-trifluoroethanol (TFE). The morphology, crystallinity and mechanical properties of the electrospun nylon-6,66,1010 fibers were investigated by scanning electron microscope (SEM), differential scanning calorimetry (DSC), wide angle X-ray diffraction (WAXD) and tensile test. The effects of electrospun process parameters such as solution concentration, voltage and tip-to-collector distance on the morphology and the average size of the electrospun fibers were also studied. The results show that the spinnable concentration of nylon-6,66,1010/TFE solution is in the range of 6-14 wt%, and higher solution concentration favors the formation of uniform fibers without beads. The diameters of the electrospun fibers increase with increasing the solution concentration and decrease slightly with increasing the voltage and needle tip-to-collector distance. But no obvious morphology changes were found with the increase of the voltage and collection distance. DSC and WAXD results suggest that the electrospun nylon-6,66,1010 membranes have lower crystallinity than those of the corresponding casting films. The electrospun nylon-6,66,1010 membrane obtained from the 14 wt% concentration exhibits the largest tensile strength and elongation at break.     

Combination of mid- and near-infrared spectroscopy for the determination of the quality properties of beers

The combination of infrared (MIR) and near-infrared (NIR) spectroscopy has been employed for the determination of important quality parameters of beers, such as original and real extract and alcohol content. A population of 43 samples obtained from the Spanish market and including different types of beer, was evaluated. For each technique, spectra were obtained in triplicate. In the case of NIR a 1 mm pathlength quartz flow cell was used, whereas attenuated total reflectance measurements were used in MIR. Cluster hierarchical analysis was employed to select calibration and validation data sets. The calibration set was composed of 15 samples, thus leaving 28 for validation. A critical evaluation of the prediction capability of multivariate methods established from the combination of NIR and MIR spectra was made. Partial least squares (PLS) and artificial neural networks (ANN) were evaluated for the treatment of data obtained in each individual technique and the combination of both. Different parameters of each methodology were optimized. A slightly better predictive performance was obtained for NIR-MIR combined spectra, and in all the cases ANN performs better than PLS, which may be interpreted from the existence of some non-linearity in the data. The root-mean-sqare-error of prediction (RMSEP) values obtained for the combined NIR-MIR spectra for the determination of real extract, original extract and ethanol were 0.076% w/w, 0.14% w/w and 0.091% v/v.     

Mechanical properties of fiber reinforced styrene-butadiene rubbers using surface-modified UHMWPE fibers under EB irradiation

Aiming to develop a high performance fiber reinforced rubber of SBR, a special technique using electron beam (EB) irradiation-induced graft-polymerization was applied to ultra-high molecular-weight polyethylene (UHMWPE) fibers. Although UHMWPE is chemically inert, N-vinyl formamide (NVF) could be graft-polymerized onto the UHMWPE fiber surface with this special technique. A maximum grafting percentage of 23.6% was achieved. The composite of SBR and grafted UHMWPE fibers with maximum grafting indicated a linear increase in the initial modulus and strength with the fiber content. At the fiber content of 10%, the initial modulus was improved about five times with respect to that of the pure SBR, while the strength was done about twice. At this moment, only a small reduction could be observed in the strain compared with that of pure SBR. The fiber reinforced rubber with a good performance was obtained in the system of SBR and grafted UHMWPE fibers.     

Total and Semi‐Syntheses of Antimicrobial Thuggacin Derivatives

The total and semi‐synthesis of 13 new macrolactones derived from thuggacin, which is a secondary metabolite from the myxobacterium Sorangium cellulosum, are reported. The thuggacins have attracted much attention due to their strong antibacterial activity, particularly towards Mycobacterium tuberculosis. This study focuses on 1) thuggacin derivatives that cannot equilibrate by transacylation between the three natural thuggacins A–C, 2) the roles of the thiazole ring, and 3) the hexyl side chain at C2. Semi‐synthetic O‐methylation at C17 suppressed the transacylations without a substantial loss of antibacterial activity. Exchanging the C17–C25 side chain for simplified hydrophobic chains led to complete loss of antibacterial activity. Exchange of the thiazole by an oxazole ring or removal of the hexyl side chain at C2 had no substantial effect on the biological properties.