343 nm飞秒激光制备微孔阵列以增强聚氨酯合成革透湿性

为了提高聚氨酯(PU)合成革透湿性,分别使用343 nm飞秒激光和作为对比的1030 nm飞秒激光及1064 nm纳秒激光制备微孔阵列。采用扫描电镜(SEM)和3D激光扫描显微镜对比研究了微孔形貌。结果表明,343 nm飞秒激光可以制备出效果最佳的微孔。此外,分析了3种激光与PU涂层的作用机理,揭示了343 nm飞秒激光合成革微钻孔过程仅表现为光化学烧蚀,光化学和光热烧蚀同时发生于1030 nm飞秒激光钻孔过程,而1064 nm纳秒激光只显示了光热烧蚀。激光合成革表面钻孔后,测量其透湿性和抗张力。结果显示: 微孔密度越大,皮革透湿性(WVP)越大而抗张力越低,脉冲重叠的增加会导致WVP的增加和抗张力的下降;同时,随着脉冲重叠从91.7%降到50%,微孔直径从45 μm降低到30 μm,而微孔锥度从0.7°增加到12.1°;当脉冲重叠率为91.7%,微孔密度为2550/cm²时,最大的WVP增长率为306%。     

基于荧光玻璃的高效LED白光技术

采用高温熔融法制备了一定质量比例的SiO_2-YAG∶Ce~(3+)片状荧光玻璃,厚度为0.2 mm,分析其XRD物相、光学和SEM微观结构、PL光谱。结果表明:荧光玻璃保留了晶相,荧光粉颗粒在玻璃基质中均匀分布,荧光玻璃和荧光粉的激发响应关系一致。在465 nm蓝光激发下,发射波长均在535 nm附近,表明荧光玻璃除含有玻璃相,还有荧光粉的物质结构特性。将不同波长蓝光芯片与不同荧光粉含量的荧光玻璃进行封装测试,结果表明:器件的流明效率可达到234.81 lm/W;色温和显色指数均随荧光粉含量增加而单调下降,呈现高色温和低显色指数;荧光粉质量分数从6%增加至15%时,不同波长激发下的色坐标x与y呈现大致相同的线性变化率。采用450 nm激光激发荧光玻璃,测试样品温度变化发现温升较缓,温降迅速,耐热性能优越。实验结果表明,将荧光玻璃用于LED白光照明封装,能实现流明效率和耐热性能的大幅提升,形成良好的白光输出。     

高功率LED热特性测试方法研究与应用

叙述了利用动态电学测试方法测量高功率LED热阻和结温的原理、试验装置、测量步骤和影响测试结果的因素.研究结果表明,该方法具有测试结构简单、稳定性高等特点,可作为高功率LED热阻和结温的一种测试方法.     

Corrosion resistance and lubricated sliding wear behaviour of novel Ni-P graded alloys as an alternative to hard Cr deposits

Alternative process to hexavalent chromium, substitute materials and new designs are urgently needed owing to the requirement of “clean” manufacture. This comparative study was conducted to systematically investigate the corrosion resistance and lubricated sliding wear behavior of graded Ni-P alloy deposits produced from a single plating bath by electrodeposition and hard Cr deposits, using potentiodynamic polarization and reciprocating ball-on-disc tribometer. Results showed that Ni-P deposits heat-treated at 400 °C with maximum hardness exhibited more than two orders of magnitude higher corrosion resistance than hard Cr deposits in 10 wt.% HCl solution. The Stribeck curves for the heat-treated Ni-P gradient deposits and hard Cr under lubrication conditions were obtained with accurate control of normal load and sliding speed during the wear process, three main different regimes corresponding to different lubrication mechanism were identified. Heat-treated Ni-P gradient deposits showed relatively poor wear resistance than hard Cr deposits under the lubrication conditions, which may be attributed to superior oil-retaining surface structure and the unique “nodular” effect of hard Cr in wear process.     

Nanostructured Cu-CGO anodes fabricated using a microwave-assisted glycine–nitrate process

This work reports a study of nanostructured copper-doped gadolinium cermet (Cu-CGO) composite anodes prepared via conventional synthesis (CS) and microwave-synthesis (MS) involving the glycine–nitrate process (GNP). A detailed investigation on the mechanical properties, electrical conductivity and electrochemical performance of prepared Cu_0.5(Ce_0.9Gd_0.1)_0.5O_2−δ anodes is included. The prepared samples were characterized by techniques, such as XRD, EDX, SEM and electrical characterizations. After reduction in 10% H₂ and 90% N₂, the DC conductivities of the Cu-CGO anodes prepared via CS-GNP and MS-GNP are found to be 5.43×10³ and 1.09×10⁴ S cm⁻¹ at 700 °C, respectively. The electrochemical performances of the spin-coated anode symmetrical cells sintered at 700 °C are evaluated at cell operating temperatures of 600, 700 and 800 °C. The lowest area specific resistance (ASR) values for the Cu-CGO/CGO/Cu-CGO symmetrical cells prepared via the MS-GNP route at operating temperatures of 600, 700 and 800 °C are found to be 0.34, 0.71 and 1.10 Ω cm², respectively. The as-prepared (via MS-GNP) Cu-CGO anode exhibits excellent electrical and electrochemical performance consistent with the uniform nanostructured morphology compared with the anode prepared via CS-GNP.     

The effect of PVA (Bi2O3-doped) interfacial layer and series resistance on electrical characteristics of Au/n-Si (110) Schottky barrier diodes (SBDs)

Two types of Schottky Barrier Diodes (SBDs) with and without PVA (Bi₂O₃-doped) polymeric interfacial layer, were fabricated and measured at room temperature in order to investigate the effects of the PVA (Bi₂O₃-doped) interfacial layer on the main electrical parameters such as the ideality factor (n), zero-bias barrier height (Φ_B0), series resistance (R_s) and interface-state density (N_ss). Electrical parameters of these two diodes were calculated from the current-voltage (I-V) characteristics and compared with each other. The values of Φ_B0, n and R_s for SBDs without polymeric interfacial layer are 0.71 eV, 1.44 and 4775 Ω, respectively. The values of Φ_B0, n and R_s for SBDs with PVA (Bi₂O₃-doped) polymeric interfacial layer are 0.74 eV, 3.49 and 10,030 Ω, respectively. For two SBDs, the energy density distribution profiles of interface states (N_ss) were obtained from forward-bias I-V measurements by taking the bias dependence of R_s of these devices into account. The values of N_ss obtained for the SBD with PVA (Bi₂O₃-doped) polymeric interfacial layer are smaller than those of the SBD without polymeric interfacial layer.     

分压与限流线路特性分析

在电学实验的创新设计类问题中,常常涉及到滑线变阻器的分压线路和限流线路。本文对滑线变阻器的分压线路和限流线路的特性作一较系统的分析,对涉及到此类问题的实际工作具有指导意义。     

金纳米薄膜导电和导热性质的实验研究

由于尺寸效应和晶界效应的影响,纳米薄膜在导电和导热方面呈现出与体材料不同的性质.本文实验研究了不同厚度(20～54 nm)金薄膜在不同温度(100～340 K)的导电、导热性质.测量结果显示,薄膜的电导率和热导率比体材料小,洛伦兹数比体材料大,Wiedemann-Franz定律不再成立.随着厚度增加,薄膜的电导率,热导率和电阻温度系数都增加.薄膜热导率随温度变化趋势与体材料相反,随着温度升高而升高.电导率随温度变化趋势与体材料相同,随着温度升高而降低;但薄膜没有体材料对温度变化敏感,导致电阻温度系数下降.     

电源频率可调的单相旋转磁场实验仪

设计了电源频率可调的单相交流电产生的旋转磁场实验仪,应用该仪器可测量电感、损耗电阻、转速等     

Corrosion resistance and blood compatibility of lanthanum ion implanted pure iron by MEVVA

Pure iron is a potential material applying for coronary artery stents based on its biocorrodible and nontoxic properties. However, the degradation characteristics of pure iron in vivo could reduce the mechanical stability of iron stents prematurely. The purpose of this work was to implant the lanthanum ion into pure iron specimens by metal vapor vacuum arc (MEVVA) source at an extracted voltage of 40 kV to improve its corrosion resistance and biocompatibility. The implanted fluence was up to 5 × 10¹⁷ ions/cm². The X-ray photoelectron spectroscopy (XPS) was used to characterize the chemical state and depth profiles of La, Fe and O elements. The results showed lanthanum existed in the +3 oxidation state in the surface layer, most of the oxygen combined with lanthanum and form a layer of oxides. The lanthanum ion implantation layer could effectively hold back iron ions into the immersed solution and obviously improved the corrosion resistance of pure iron in simulated body fluids (SBF) solution by the electrochemical measurements and static immersion tests. The systematic evaluation of blood compatibility, including in vitro platelets adhesion, prothrombin time (PT), thrombin time (TT), indicated that the number of platelets adhesion, activation, aggregation and pseudopodium on the surface of the La-implanted samples were remarkably decreased compared with pure iron and 316L stainless steel, the PT and TT were almost the same as the original plasma. It was obviously showed that lanthanum ion implantation could effectively improve the corrosion resistance and blood compatibility of pure iron.