生长温度对碳纳米管阴极场发射性能的影响

碳纳米管(Carbon Nanotubes,CNTs)场发射平面显示器(Field Emission Display,FED)与其他显示器比较显示了其独特优点,被认为是未来理想的平面显示器之一。碳纳米管阴极作为器件的核心部分,其性能的好坏直接影响显示器的性能。针对30~60英寸(76.2~152.4cm)大屏幕显示器所用的厚膜工艺,即采用丝网印刷法制备了碳纳米管阴极阵列,研究了化学气相沉积法在不同温度下生长的CNTs的场发射电流-电压特性,找到了适合FED用碳纳米管的最佳生长温度。结果表明生长温度越高(750℃),CNTs场发射性能越好。并用荧光粉阳极测试这些CNTs的场发射发光显示效果,验证了上述结论。     

宽带膜厚实时监控过程中膜层折射率的确定方法

为了准确计算出镀膜过程中每层膜的折射率，介绍了实时监控过程中确定膜层折射率的2种方法：一种是由实测的透射比光谱直接反算出膜层的折射率；另一种是用最小二乘法的优化算法实时拟合折射率。试验结果表明：在线反算适合单点监控，所得折射率误差小于2%。然而在实际镀膜过程中,由于宽带内膜层参数误差较大,一般大于25%。为此，采用最小二乘法拟合，即在整个宽光谱范围内采集每个波长点的信息，所得结果误差很小，一般都在2％～5%之间,有时可达到10%,在很大程度上提高了实际镀膜时膜厚监控的精度。     

掺钕聚甲基丙烯酸甲酯的光学特性

研究了制备的掺钕螯合物Nd(DBM)3Phen材料的吸收光谱、激发光谱、荧光光谱,应用Judd-Ofelt理论计算了该材料的强度参量．分析了钕离子激发态4F3／2的辐射寿命(631 μs)和4F3／2→4IJ′跃迁的受激发射截面和荧光分支比．     

弱(L_1,L_2)-BLD映射的正则性

本文首先将文［１］中的ＢＬＤ映射推广为弱（Ｌ１，Ｌ２）－ＢＬＤ映射，并证明了如下正则性结果：存在两个可积指数 Ｐ１＝Ｐ１（ｎ，Ｌ１，Ｌ２）＜ｎ＜ｑ１＝ｑ１（ｎ，Ｌ１，Ｌ２），使得对任意弱（Ｌ１，Ｌ２）－ＢＬＤ映射ｆ∈（Ω，Ｒｎ），都有ｆ∈（Ω，Ｒｎ），即ｆ为（Ｌ１，Ｌ２）－ＢＬＤ映射．     

不同入射角度下强流脉冲电子束能量沉积剖面和束流传输系数模拟计算

 强流脉冲电子束在材料中的能量沉积剖面、能量沉积系数和束流传输系数受其入射角的影响很大，理论计算了0.5~2.0MeV的电子束以不同的入射角在Al材料中的能量沉积剖面和能量沉积系数，并且还计算了0.4~1.4MeV电子束以不同入射角穿透不同厚度C靶的束流传输系数。计算结果表明，随着入射角的增大，靶材表面层单位质量中沉积的能量增大，电子在靶材料中穿透深度减小，能量沉积系数减小，相应的束流传输系数也减小；能量为0.5~2.0MeV的电子束当入射角在60°~70°时在材料表面层单位质量中沉积的能量较大。     

基因芯片荧光图象采集与分析

描述了基因芯片荧光图象的光学共聚焦成象,大范围高速扫描与控制,数据采集的原理和方法.并讨论了基因芯片荧光图象的分析算法,即模板定位与阈值分割相结合的半自动算法,并将其计算结果与完全采用人工分割算法的结果进行了比较.     

Asymptotique de la norme $L^2$ d'un cycle géodésique dans les revêtements de congruence d'une variété hyperbolique arithmétique

Let M be an arithmetic hyperbolic manifold and be a codimension 1 geodesic cycle. In this paper, we study the asymptotic growth of the -norm of the lifts of F in the congruence tower above M. We obtain an explicit value for the growth rate of this norm. In particular, we provide a new proof of a celebrated result of Millson [Mi] on the homology of the arithmetic hyperbolic manifolds. The method is quite general and gives a new way of getting non zero homology classes in certain locally symmetric spaces. Received: 20 April 2001; in final form: 26 September 2001 / Published online: 28 February 2002     

Biodegradable/biocompatible ABC triblock copolymer bearing hydroxyl groups in the middle block

New biodegradable/biocompatible ABC block copolymers, poly(ethylene oxide)‐b‐poly(glycidol)‐b‐poly(L ,L ‐lactide) (PEO‐PGly‐PLLA), were synthesized. First, PEO‐b‐poly(1‐ethoxyethylglycidol)‐b‐PLLA was synthesized by a successive anionic ring‐opening copolymerization of ethylene oxide, 1‐ethoxyethylglycidyl ether, and L ,L ‐lactide initiated with potassium 2‐methoxyethanolate. In the second step, the 1‐ethoxyethyl blocking groups of 1‐ethoxyethylglycidyl ether were removed at weakly acidic conditions leaving other blocks intact. The resulting copolymers were composed of hydrophilic and hydrophobic segments joined by short polyglycidol blocks with one hydroxyl group in each monomeric unit. These hydroxyl groups may be used for further copolymer transformations. The PEO‐PGly‐PLLA copolymers with a molecular weight of PLLA blocks below 5000 were water‐soluble. Above the critical micellar concentration (ranging from 0.05 to1.0 g/L, depending on the composition of copolymer), copolymers formed macromolecular micelles with a hydrophobic PLLA core and hydrophilic PEO shell. The diameters of the micelles were about 25 nm. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3750–3760, 2003     

Active long pulse shaping technique of pulsed CO2 laser using multi-pulse discharge control

We describe the pulse forming of pulsed CO₂ laser using multi-pulse superposition technique. Various pulse shapes, high duty cycle pulse forming network (PFN) are constructed by time sequence. This study shows a technology that makes it possible to make various long pulse shapes by activating SCRs of three PFN modules consecutively at a desirable delay time with the aid of a PIC one-chip microprocessor. The power supply for this experiment consists of three PFN modules. Each PFN module uses a capacitor, a pulse forming inductor, a SCR, a high voltage pulse transformer, and a bridge rectifier on each transformer secondary. The PFN modules operate at low voltage by driving the primary of HV pulse transformer. The secondary of the transformer has a full-wave rectifier, which passes the pulse energy to the load in a continuous sequence.We investigated various long pulse shapes as different trigger time intervals of SCRs among three PFN modules. As a result, we could obtain laser beam with various pulse shapes and durations from about 250 to 1000 μs.     

贝克曼AllegraTM21R型超高速离心机故障排除一例

贝克曼Allegra^TM 21R型超高速离心机开机后，操作面板上出现错误代码“28”，离心机不旋转。离心机的电机采用无刷感应驱动，由电机驱动电源模块BSMl0GD60DN2驱动离心机的电机。故障是由于电源模块BSMl0GD60DN2损坏引起的。采用东芝三相桥式IGBT电源模块MG25Q6ES42代替BSMl0GD60DN2，并更换已烧毁的栅极电阻后。开机试验，仪器恢复正常。