PS／LDPE共混体系相结构的TEM研究

ＰＳ／ＬＤＰＥ共混体系相结构的ＴＥＭ研究徐世爱，江明，沈静姝（复旦大学高分子科学系和聚合物分子工程实验室，上海，２００４３３）（中国科学院化学研究所高分子物理开放实验室）关键词相结构，透射电镜，共混体系聚苯乙烯（ＰＳ）和低密度聚乙烯（ＬＤＰＥ）共混体...     

聚丙烯-聚乙烯嵌段共聚物的分子结构及性能的研究

本工作用核磁共振(~(13)C-NMR)、示差扫描量热(DSC)、动态力学分析(DMA)和扫描电子显微镜(SEM)等技术研究了将丙烯、乙烯单体两步分段共聚、预期为聚丙烯-聚乙烯嵌段共聚物的合成物(简称为聚丙烯-聚乙烯嵌段共聚物或嵌段共聚物)。结果表明,在嵌段共聚物中含有一定量的、能为正庚烷抽提出来的乙丙无规共聚物(EPR);分段共聚的产物并非预想的PP-b-PE两嵌段共聚物,而是含有多种组分的共混物;形态表征的结果表明了嵌段共聚物为多相体系,EPR和PE形成分散相以球形无规分布于PP基体中。     

Effect of the polarity of additional solvent on membrane formation in polysulfone/N-methyl-2-pyrrolidone/water ternary system

Asymmetric polysulfone membranes were prepared by wet phase inversion method with different demixing rate of casting solutions. The influent factor of demixing rate was focused on the polarity of additive in the polysulfone/N-methyl-2-pyrrolidone/water ternary system. With increasing the polarity of alcohols in the casting solution, the decrease in skin layer thickness was observed and then a poor separation performance of membranes can be obtained. It was found that the polar additive caused the rapidly demixing of casting solution in coagulation bath and formed porous asymmetric membranes with defective skin layer. In the other case, chloroform was used as the non-polar additive in casting solution. With increasing the mount of chloroform in the casting solution, the increase in skin layer thickness was observed and then lead to a good separation performance of these membranes. It was found that of the non-polar additive delays the demixing rate of casting solution in this ternary system. The separation performance of these asymmetric membranes were characterized by the measurement of dehydration of ethanol/water mixture by pervaporation and observed the morphology by scanning electron microscopy. It was found that the separation performance of asymmetric polysulfone membrane strongly depends on the polarity of adding solvent in polysulfone/N-methyl-2-pyrrolidone/water ternary system.     

Morphology and transport properties of protons and methanol through partially sulfonated block copolymers

The morphological changes with different compositions of casting solvents in the membranes of sulfonated polystyrene-block-poly(ethylene-ran-butylene)-block-polystyrene (SEBS) were investigated with small-angle X-ray scattering (SAXS) and transmission electron microscope (TEM). Using the single solvent of tetrahydrofuran (THF) and the solvent mixtures of methanol/THF with different compositions, the casting polymer solutions were prepared for the membrane fabrication. The proton conductivity and the methanol permeability of membranes were measured, and the effect of morphological changes on the casting solvents was discussed through Flory–Huggins theory. It was found that the sulfonated SEBS membranes were transformed from well ordered lamellar to disordered co-continuous structure and the morphological difference caused abrupt enhancement in the proton conductivity and the methanol permeability as the concentration of methanol in the mixed solvents (MeOH/THF) increased.     

Preparation of multihollow P(St-MAA) particles by sequence soap-free/soap emulsion polymerization and followed by stepwise alkali/acid posttreatment

The effects of ionic emulsifier, sodium dodecylbenzene sulfate (SDBS), on the formation of the multihollow structures in sub-micron sized polymer particles produced by alkali/acid posttreatment were investigated. The original latex particles with narrow size distribution were synthesized by a new sequence emulsifier-free/emulsifier emulsion copolymerization of styrene (St) and methacrylic acid (MAA). Results indicated that the pore size decreased and the pore number increased with the increase of SDBS amount, and the morphology of the posttreated latex particles was also significantly influenced by the introducing time of SDBS in the preparation of the original latex particles, and a suitable introducing time was 3 h of polymerization.     

Polymeric positive-temperature-coefficient materials: dynamic curing effect

The object of this work was to prepare high-density polyethylene (HDPE)/ethylene–propylene–diene terpolymer (EPDM)/conductive carbon black (CB) composites by dynamic curing and to characterize the positive-temperature-coefficient (PTC) performances of the composites.EPDM and dicumyl peroxide were preblended in a research mill. The roll-milled strands were blended with HDPE and CB in a Haake mixer. The sheet resistivity and morphology of the HDPE/EPDM/CB composites with or without the dynamic curing process were investigated. It was concluded that the dynamically cured blends exhibit better PTC performance than the simple blends without dynamic curing. The effects of shear intensity and dicumyl peroxide content during the dynamic curing process were discussed for the PTC characteristics of the HDPE/EPDM/CB composites.     

LOW DENSITY POLYETHYLENE/CLAY NANOCOMPOSITES MODIFIED BY ETHYLENE COPOLYMERS： EFFECTS OF FUNCTIONALIZED SEGMENTS ON MORPHOLOGY

Melt extrusion was used to prepare binary nanocomposites of ethylene copolymers and organoclay and trinary nanocomposites of low-density polyethylene （LDPE）, ethylene copolymer and organoclay. X-ray diffraction （XRD） and transmission electron microscopy （TEM） were used to analyze the structure of the clay phase and the morphology of the nanocomposites. Influences of the comonomer in the copolymer and the content of the copolymer on the morphology of the resulting nanocomposites were discussed. The binary and the trinary composites may form intercalated or exfoliated structures depending on the interaction between the copolymer and the clay layers and the content of the copolymer.     

In situ preparation of polyaniline coated fumed and precipitated silica fillers and their composites with nitrile rubber (Investigation on structure-property relationship)

In situ synthesis of polyaniline (PAni) coated pyrogenic or fumed silica (PCFS) and precipitated silica (PCPS) were carried out by the oxidative polymerization of aniline in presence of fumed silica (FS) and precipitated silica (PS). Both uncoated and PAni coated silica fillers were characterized through scanning electron microscope (SEM), infrared spectroscopy and thermo-gravimetric analysis (TGA) to evaluate particle morphology and physico-chemical character of coated and uncoated silica particles. Semi-conducting composites made from two different types of PAni coated silica fillers with NBR exhibit different trend in the variation of electrical properties under different temperature and pressure. These differences in electrical properties of two types of composites are mainly due to physico-chemical characteristics of filler particles as well as their distribution in the polymer matrix. This type of composites may be used as semi-conducting and ESD (electrostatic discharge) material.     

Miscibility and transesterification in ternary blends of poly(ethylene naphthalate)/poly(trimethylene terephthalate)/poly(ether imide)

Miscibility and morphology of poly(ethylene 2,6-naphthalate)/poly(trimethylene terephthalate)/poly(ether imide) (PEN/PTT/PEI) blends were investigated by using a differential scanning calorimeter (DSC), optical microscopy (OM), wide-angle X-ray diffraction (WAXD), and proton nuclear magnetic resonance (¹H-NMR). In the ternary blends, OM and DSC results indicated immiscible properties for polyester-rich compositions of PEN/PTT/PEI blends, but all compositions of the ternary blends were phase homogeneous after heat treatment at 300 °C for more than 30 min. An amorphous blend with a single T _g was obtained in the final state, when samples were annealed at 300 °C. Experimental results from ¹H-NMR identified the production of PEN/PTT copolymers by so-called “transesterification”. The influence of transesterification on the behaviors of glass transition and crystallization was discussed in detail. Study results identified that a random copolymer promoted the miscibility of the ternary blends. The critical block lengths for both PEN and PTT hindered the formation of crystals in the ternary blends. Finally, the transesterification product of PEN/PTT blends, ENTT, was blended with PEI. The results for DSC and OM demonstrated the miscibility of the ENTT/PEI blends.     

The morphological effects upon enzymatic degradation of poly(butylene succinate-co-butylene terephthalate)s (PBST)

In this work, the enzymatic degradation of poly(butylene succinate-co-butylene terephthalate) (PBST) copolyesters was studied using the lipase from Pseudomonas (Lipase PS^®). The biodegradation behavior was found to strongly depend on the overall impacts of several important factors as the BT comonomer structure and molar content, thermal characteristics, morphology, the enzyme-substrate, and so forth. Further, the biodegraded residual film samples were allowed to be analyzed by means of gel permeation chromatography (GPC), proton nuclear magnetic resonance (¹H NMR), differential scanning calorimeter (DSC), small angle X-ray scattering (SAXS), and scanning electron microscope (SEM). On the experimental evidences, an exo-type mechanism of enzymatic chain hydrolysis preferentially occurring in the amorphous region was suggested for the PBST film samples.