双亲半柔性两嵌段共聚物在溶液中自组装形态的模拟退火研究

针对一系列疏溶剂嵌段与溶剂间的相互作用,用模拟退火方法研究了双亲半柔性两嵌段共聚物在溶液中的自组装形态.模拟结果显示共聚物在溶液中均形成核-壳聚集体,其中疏溶剂嵌段形成聚集体的核,亲溶剂嵌段形成聚集体的壳.当上述相互作用较小时,核呈球形,而壳如同长在核上的刺.随着上述相互作用的增大,核逐渐增大.在较大的相互作用时,核呈柱形;而随着相互作用的加大,长在核上的刺逐渐伏贴于核表面.在更大的相互作用时,核又呈球状,壳伏贴于核表面.     

Morphology of peroxide-prevulcanised natural rubber latex: effect of reaction time and deproteinisation

A non-uniform mesh structure, i.e. a dense network near the surface of peroxide-prevulcanised natural rubber latex particles, was observed under transmission electron microscopy. In the initial period of prevulcanisation, the swelling ratio of the latex sheet decreased with longer reaction time while an increase in crosslink density of rubber particles containing polystyrene, prepared using the phase transfer/bulk polymerisation process, was noticed. The modulus of the rubber sheet increased up to maximum crosslinking and thereafter decreased. After removal of proteins from the latex membrane layer, derived from protein-lipid originally existing at the rubber particle surface, could not be detected. The absence of proteins, which act as free radical scavengers, resulted in a rapid diffusion of alkoxy radicals into the rubber phase of deproteinised latex and, therefore, a uniform crosslink distribution inside each particle was obtained.     

关于超高分子量聚丙烯超拉伸膜的结构性能的研究——Ⅱ.形态结构变化对力学性能的影响

用X-射线衍射、动态力学测定等手段研究了不同拉伸倍数的超高分子量聚丙烯薄膜的力学性能的变化.以X-射线衍射法并基于串联力学模型的假设得到的各样品的表观晶区模量E_c~(app)约为34-38GPa.样品模量E_b随拉伸倍数增加而逐渐增大,其变化趋势与非晶区取向因子的变化相类似,说明非晶区取向是左右样品模量的重要因素.室温下,69倍拉伸样品的模量为27GPa,约为表观结晶模量的3/4,且其值在-150-160℃的温度范围内没有急剧变化,说明超拉伸明显改善了材料的力学性能及热稳定性.在各拉伸样品中,考虑伸直链结晶生成的可能性,利用并串联力学模型对伸直链结晶的体积分数做了估算,并对X-射线衍射法所得表观结晶模量进行了修正,认为室温下聚丙烯的真正晶区模量约为47GPa.     

高密度聚乙烯／超高分子量聚乙烯共混物高取向薄膜形态结构与力学性能的研究

高密度聚乙烯／超高分子量聚乙烯共混物高取向薄膜形态结构与力学性能的研究张伟广，赵勇，杨德才中国科学院长春应用化学研究所，高分子物理开放实验室，长春，１３００２２）关键词ＨＤＰＥ、ＵＨＭＷＰＥ、共混物、形态结构、力学性能如何提高高分子材料抗张强度和模量...     

含聚醚间隔链的扩链脲改性环氧树脂/双氰双胺固化体系性能研究

合成了一系列含不同分子量聚环氧丙烷 (PPG)柔性间隔链的扩链脲 ,系统考察了扩链脲改性环氧树脂E 5 1/双氰双胺 (dicy)固化体系的固化反应活性、动态力学行为、冲击性能和断裂面形态结构 ,并对体系的冲击性能、形态结构与动态力学行为之间的关系进行了探讨 .结果表明 ,改性体系固化反应活性明显提高 ,固化反应表观活化能降低 ,固化反应峰顶温度从 190℃降低至 14 0℃ ,固化反应的表观活化能由 14 5 5kJ/mol降至 70～ 80kJ mol;改性体系冲击强度明显提高 ,其中所含PPG柔性链分子量为 10 0 0的扩链脲改性的E 5 1/dicy体系冲击强度较未改性的E 5 1/dicy体系提高了 8倍 ,其冲击试样断裂面的形态具有明显的韧性断裂特征 ,微观两相网络结构的存在导致了改性体系冲击强度显著提高     

Morphology controls of the melt blending in a novel highly crosslinked bismaleimide system

A novel bismaleimide of 2,2-bis[4-(4-maleimidophenoxy)phenyl]propane (BMIP) with a broad working-temperature-range for the melt blending was successfully synthesized. BMIP possesses a considerably broad working-temperature-range from 75 °C to 250 °C, prior to undergoing cure reactions to form a highly crosslinked network. The morphology types of cured BMIP/clay hybrids can be controlled by varying the shearing temperatures and the contents of the clay. The conditions necessary for achieving an exfoliated or an intercalated BMIP/clay hybrid were thoroughly investigated via X-ray diffractometry, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). All the uncured samples prepared at different shearing temperatures and with an adequate amount of MMT-C (above 3 phr) exhibited an intercalated form of morphology. However, the crosslinking reactions for specified samples prepared at relatively elevated shearing temperatures (above 120 °C) and with a relatively low content of clay (below 15 phr) resulted in morphology changes from the intercalated form to the exfoliated form of morphology. There exists an isotropically mechanical property for the cured matrix of the exfoliated hybrids whereas there exists an anisotropically mechanical property for the cured matrix of the intercalated hybrids.     

CRYSTAL STRUCTURE AND MORPHOLOGY OF NASCENT SAMPLES OF SYMMETRIC AROMATIC POLYESTERS I.POLY(P-PHENYLENE TEREPHTHALATE)

The morphology and crystal structure of poly(p-phenylene terephthalate) (PPT), prepared by confined thin film melt (CTFMP) and solution (CTFSP) and bulk solution polymerization, were characterized by transmission electron microscopy, electron diffraction and molecular modeling. The unit cell is monoclinic (P21/a space group) with parameters a =7.89, b = 5.49, c =12.65 A α= γ= 90°,β= 100.33°, density = 1.48 g/cm3, the a, b andβ values differing slightly from those reported previously in the literature. A degree of variation in relative intensities of hk0 reflections in, apparently, untilted [001] ED patterns was observed from a given sample, suggesting some variation in molecular packing. ED evidence was found for a second phase, with [001] appearing the same as for phase Ⅱ of the related poly(p-oxybenzoate) (PpOBA)polymer. CTFMP crystals polymerized above 220°C (up to 370°C) and CTFSP crystals polymerized at 300°C consisted of lamellae 100-200 A thick.     

端羟基芳香酯二醇扩链的聚氨酯－酯的DSC研究

端羟基芳香酯二醇扩链的聚氨酯－酯的ＤＳＣ研究陈静，余学海，杨昌正（南京化工学院应化系南京２１０００９）（南京大学化学系南京２１００９３）关键词嵌段聚醚聚氨酯－酯，结晶性，微观相结构，差示扫描量热法，形态结构众所周知，聚氨酯嵌段共聚物是一类结构特殊、用...     

Habit modification of calcium carbonate in the presence of malic acid

The ability of malic acid to control calcium carbonate morphology has been investigated by aging calcium chloride solution in the presence of urea in a 90 °C bath. Malic acid favors the formation of calcite. A transition from single block to aggregate with special morphology occurs upon increasing malic acid concentration. The morphological development of CaCO₃ crystal obviously depends on the starting pH. CaCO₃ crystal grows from spindle seed to dumbbell in the pH regime from 7 to 11; while it evolves from spindle seed, through peanut, to sphere at pH=11.5. Both dumbbell and sphere consist of rods that are elongated along c-axis and capped with three smooth, well-defined rhombic {1 0 4} faces. A tentative growth mechanism is proposed based on the fractal model suggested by R. Kniep and S. Busch [Angew. Chem. Int. Ed. Engl. 35 (1996) 2624].     

Zr（Y）O2衬底上大面积YBCO薄膜表面组织状态的研究

使用配备有ＥＤＳ和ＥＣＰ附件的ＳＥＭ、ＡＥＭ、和ＳＴＭ研究在７５０和８００℃的Ｚｒ（Ｙ）Ｏ２衬底上磁控溅射沉积的大面积ＹＢＣＯ超导薄膜的表面组织。ＹＢＣＯ薄膜为ｃ轴取向单晶，但衬底温度为８００℃时，膜表面的突出组织多为ＣｕＯ颗粒，小坑较多，表面粗糙；衬底温度为７５０℃时，突出组织多为棒状和多边形１２３结构，很少小坑，表面较平整。