Controlled structure and density of “living” polystyrene brushes on flat silica surfaces

Thin layers of polystyrene were grown from surface-grafted nitroxide initiators via controlled “living” free radical polymerization. The “reactive” Langmuir-Blodgett deposition method allowed an effective control of the initiator layer density leading to PS brushes with different and high grafting density and stretching. The influence of the grafting density on the layer structure was studied. Comparison with theoretical predictions for monodispersed brushes in bad solvent was discussed. The thickness was found to vary linearly with molecular weight and the density dependence was shown using wetting measurements. Special features of controlled radical nitroxide polymerization from a surface were discussed. A direct comparison of the molecular weight and polydispersity between surface and bulk polymers was made by de-grafting the brushes into a toluene/HF solution. Finally, some evidence of a “surface Fischer” effect was shown from re-initiated layers. Received 20 December 2001     

Structural and lithium intercalation studies of Mn(0.5−x)CaxTi2(PO4)3 phases (0≤x≤0.50)

Materials from the Mn_(0.5−x)Ca_xTi₂(PO₄)₃ (0≤x≤0.50) solid solution were obtained by solid-state reaction in air at 1000 °C. Selected compositions were investigated by powder X-ray diffraction analysis, ³¹P nuclear magnetic resonance (NMR) spectroscopy and electrochemical lithium intercalation. The structure of all samples determined by Rietveld analysis is of the Nasicon type with the R space group. Mn²⁺/Ca²⁺ ions occupy only the M1 sites in the Ti₂(PO₄)₃ framework. The divalent cations are ordered in one of two M1 sites, except for the Mn_0.50Ti₂(PO₄)₃ phase, where a small departure from the ideal order is observed by XRD and ³¹P MAS NMR. The electrochemical behaviour of Mn_0.50Ti₂(PO₄)₃ and Mn_(0.5−x)Ca_xTi₂(PO₄)₃ phases was characterised in Li cells. Two Li ions can be inserted without altering the Ti₂(PO₄)₃ framework. In the 0≤y≤2 range, the OCV curves of Li//Li_yMn_0.50Ti₂(PO₄)₃ cells show two main potential plateaus at 2.90 and 2.50–2.30 V. Comparison between the OCV curves of Li//Li_(1+y)Ti₂(PO₄)₃ and Li//Li_yMn_0.50Ti₂(PO₄)₃ shows that the intercalation occurs first in the unoccupied M1 site of Mn_0.50Ti₂(PO₄)₃ at 2.90 V and then, for compositions y>0.50, at the M2 site (2.50–2.30 V voltage range). The effect of calcium substitution in Mn_0.50Ti₂(PO₄)₃ on the lithium intercalation is also discussed from a structural and kinetic viewpoint. In all systems, the lithium intercalation is associated with a redistribution of the divalent cation over all M1 sites. In the case of Mn_0.50Ti₂(PO₄)₃, the stability of Mn²⁺ either in an octahedral or tetrahedral environment facilitates cationic migration.     

Preparing polymer brushes on polytetrafluoroethylene films by free radical polymerization

Films of polytetrafluoroethylene (PTFE) were exposed to sodium naphthalenide (Na/naphtha) etchant so as to defluorinate the surface for obtaining hydroxyl functionality. Surface-initiators were immobilized on the PTFE films by esterification of 4,4′-azobis(4-cyanopentanoic acid) (ACP) and the hydroxyl groups covalently linked to the surface. Grafting of polymer brushes on the PTFE films was carried out by the surface-initiated free radical polymerization. Homopolymers brushes of methyl methacrylate (MMA) were prepared by free radical polymerization from the azo-functionalized PTFE surface. The chemical composition and topography of the graft-functionalized PTFE surfaces were characterized by X-ray photoelectron spectroscopy (XPS), attenuated total reflectance (ATR) FT-IR spectroscopy and atomic force microscopy (AFM). Water contact angles on PTFE films were reduced by surface grafting of MMA.     

Interfacial dynamics‐based modelling of turbulent cavitating flows,Part‐2: Time‐dependent computations

The interfacial dynamics‐based cavitation model, developed in Part‐1, is further employed for unsteady flow computations. The pressure‐based operator‐splitting algorithm (PISO) is extended to handle the time‐dependent cavitating flows with particular focus on the coupling of the cavitation and turbulence models, and the large density ratio associated with cavitation. Furthermore, the compressibility effect is important for unsteady cavitating flows because in a water–vapour mixture, depending on the composition, the speed of sound inside the cavity can vary by an order of magnitude. The implications of the issue of the speed of the sound are assessed with alternative modelling approaches. Depending on the geometric confinement of the nozzle, compressibility model and cavitation numbers, either auto‐oscillation or quasi‐steady behaviour is observed. The adverse pressure gradient in the closure region is stronger at the maximum cavity size. One can also observe that the mass transfer process contributes to the cavitation dynamics. Compared to the steady flow computations, the velocity and vapour volume fraction distributions within the cavity are noticeably improved with time‐dependent computations. Copyright © 2004 John Wiley & Sons, Ltd.     

Damage and fracture evaluation of granular composite materials by digital image correlation method

This paper presents the applications of digital image correlation technique to the mesoscopic damage and fracture study of some granular based composite materials including steelfiber reinforced concrete, sandstone and crystal-polymer composite. The deformation fields of the composite materials resulted from stress localization were obtained by the correlation computation of the surface images with loading steps and thus the related damage prediction and fracture parameters were evaluated. The correlation searching could be performed either directly based on the gray levels of the digital images or from the wavelet transform (WT) coefficients of the transform spectrum. The latter was developed by the authors and showed higher resolution and sensitivity to the singularity detection. Because the displacement components came from the rough surfaces of the composite materials without any coats of gratings or fringes of optical interferometry, both surface profiles and the deformation fields of the composites were visualized which was helpful to compare each other to analyze the damage of those heterogeneous materials. The project supported by the National Natural Science Foundation of China (10125211 and 10072002), the Scientific Committee of Yunnan Province for the Program of Steel Fiber Reinforced Concrete, and the Institute of Chemical Materials, CAEP at Mianyang     

数学建模与素质教育

面对二十一世纪知识经济的挑战 ,我国高等教育模式应由应试教育 ,专业教育向素质教育转变 ,培养学生自主意识 ,效率意识 ,竞争意识 ,创新意识和民主意识 ,即高校教育应重视大学生的创新能力、实践能力和创业精神 ,普遍提高大学生的人文素质和科学素质 .本文拟就提高大学生素质的有效层面 ,对开展数学建模教学与实践进行深入分析 ,以窥探数学建模与素质教育之关系 .在深入把握数学建模教学与实践内涵的同时 ,分析得出这种以不打扰现行正常秩序的教育是提高大学生素质的有效途径之一     

Microchemical Investigation of Archaeological Copper Based Artefacts Disclosing an Ancient Witness of the Transition from the Value of the Substance to the Value of the Appearance

In many Italian archaeological sites dated between the sixth and third centuries BC, unworked lumps of Cu-based materials are sometimes found, the so called Aes Rude, which according to archaeological considerations were appreciated as currency, as a medium of exchange and as a form of saving. The microchemical investigation of these ancient artefacts discloses their nature as apparently not usable for any functional applications or possible use. Indeed, Aes Rude resemble ordinary copper material, but microchemical results indicate that they are constituted by highly ferruginous leaded copper, making them useless for producing other metal objects by means of casting or hot and cold working. Notwithstanding this intrinsic negative feature, the production of these intractable Cu-based alloys was deliberately carried out to maximise the process yield in terms of produced metal from an impure and unselected metal ore by tailoring the smelting process parameters. With these considerations in mind, the microchemical investigation of these ancient iron–copper alloys gives evidence of the passage from the acceptance of an artefact value based on its true nature or potential use to the acceptance of the value based only on its appearance or form irrespective of its present or future use. This information could contribute to a better understanding of the evolution of human thought and economic and social interactions.     

Magnetotransport and magnetic properties of InAs/Mn digital alloys

We have investigated the magnetic and magneto-transport properties of a systematic sequence of five InAs/Mn digital alloys grown by a combination of molecular beam epitaxy and atomic layer epitaxy. The samples consist of 30 periods of Mn fractional monolayers (ML) (0.17–0.5 ML) separated by 14 ML thick InAs spacer layers in a superlattice configuration. Four samples show n-type electrical conduction while the fifth (0.25 ML Mn) is p-type. Squid magnetization measurements performed on these samples show remnant magnetization above room temperature, which is apparently related to a second phase.     

New Results on the Queens_n 2 Graph Coloring Problem

For the Queens_n ² graph coloring problems no chromatic numbers are available for n > 9 except where n is not a multiple of 2 or 3. In this paper we propose an exact algorithm that takes advantage of the particular structure of these graphs. The algorithm works on the independent sets of the graph rather than on the vertices to be colored. It combines branch and bound, for independent set assignment, with a clique based filtering procedure. A first experimentation of this approach provided the coloring number values ranging for n = 10 to n = 14.     

Simultaneous Pseudo-Timestepping for PDE-Model Based Optimization Problems

In this paper we present a new method for the solution of optimization problems with PDE constraints. It is based on simultaneous pseudo-time stepping for evolution equations. The new method can be viewed as a continuous reduced SQP method in the sense that it uses a preconditioner derived from that method. The reduced Hessian in the preconditioner is approximated by a pseudo-differential operator, whose symbol can be investigated analytically. We apply our method to a boundary control model problem. The new optimization method needs 3.2-times the overall computational effort of the solution of simulation problem alone.