铈改性NaZSM-5分子筛担载Pd催化剂上CO氧化性能研究

以浸渍法制备了一系列添加CeO2的Pd-Ce/NaZSM-5负载型催化剂．以C0氧化为 模型反应，考察了反应温度、Ce含量、预还原、空速及水蒸气等对C0氧化性能的影 响，并利用XIlD和朋等手段对催化剂体相及表面结构进行了表征．结果表明：加入 CeO2作助剂可明显提高催化剂的活性，且催化转化率随着反应温度及Ce含量的增加 而增加；随着空速的增加而降低；催化剂对水蒸气不敏感，在水蒸气存在的条件下 反应可连续进行720h以上保持C0完全转化；H2预还原作用使催化剂活性有所提高． XRD测试结果表明，催化剂中Pd组分处于高分散状态，Ceob的引入促进了N物种在 NaZSM—5载体上的分散．表面XPS分析证实催化剂表面Pd物种处于较高的氧化状态 ，且CeO2与Pd物种间存在协同作用．Pd的高分散及其与CeO2的相互作用是催化剂具 有高活性的关键．     

搅拌釜中制备草酸铈的团聚尺寸模型研究

以硝酸铈和草酸铵反应生成草酸铈沉淀为研究对象，探讨了搅拌釜中输入功率、溶液过饱和度与产物团聚尺寸之间的变化关系并在团聚和破碎动力学的基础上建立了团聚尺寸模型。根据草酸铈沉淀实验中得到的实验结果求得了一定反应体系浓度下的模型K1，K2和K3值，最后通过－↑LtE,max的模型计算值与实验值，ε--↑LtE的模型曲线与实验曲线的比较初步证明了该模型的实际适用性。     

K-Ce_(0.5)Zr_(0.5)O_2催化碳颗粒物燃烧性能

用等体积浸渍法制备了不同K负载量的xKNO3-Ce0.5Zr0.5O2系列催化剂,用程序升温氧化反应(TPO)考察催化剂对碳颗粒物(soot)燃烧的催化活性.并采用XRD、BET、FT-IR、XPS等技术对KNO3负载催化剂进行表征.结果表明KNO3负载量对催化剂的比表面、表面化学环境有显著的影响;KNO3能使催化剂对soot的催化燃烧活性有较大提高,且存在最佳负载量,当x=0.5时,催化剂的活性最好,碳颗粒物的起燃温度(T)i和峰顶温度(Tp)分别为290℃和360℃.在反应过程中,KNO3熔融状态的形成和K2CO3的生成,使催化活性明显提高.     

镀液中Ce^3＋离子对锡镀层结构缺陷和可焊性的影响

应用荧光分析法、X光电子能谱法(XPS)及正电子湮没寿命谱法(PALS)等研究了从含硫酸铈添加剂的酸性光亮锡镀液获得的锡镀层结构缺陷与可焊性的关系。结果表明,电镀时Ce与Sn不发生共沉积,Ce~(3+)的主要作用是阻化Sn~(2+)的水解和氧化使镀液稳定,因而使锡镀层纯度提高、结构致密、表层氧含量减少,有利于提高镀层的可焊性。当Ce~(3+)浓度控制在3.5g/L左右时,可使镀层结构缺陷较少,可焊性较佳,说明结构缺陷是影响锡镀层可焊性的直接原因。     

Jet production rates at LEP and the scale of αs

We discuss the scale dependence of _s in connection with jet multiplicities on theZ pole in the framework of perturbative QCD. Several scale defining procedures are applied to jet fractions and compared to recent measurements at LEP.Dedicated to Prof. Dr. H.J. Mang on the occasion of his 60th birthday     

Vinyl polymerization of acrylonitrile by the Ce(IV)-glucose redox system

Aqueous polymerization of acrylonitrile (M) initiated by the Ce(IV)-glucose (R) redox system has been studied under nitrogen in the temperature range of 30–40 °C. The rate of polymerization (Rp) is proportional to [M]², [R] and inversely proportional to [Ce(IV)]. The rate of ceric ion disappearance is proportional to [R] and [Ce(IV)]. The end group in the polymer is characterised by IR spectra. A suitable kinetic scheme has been proposed and explained in the light of these experimental findings.     

Spectrophotometric Studies of Cerium(III) and Thorium(IV) Chelates of Diethylenetriaminepentaacetic Acid (DTPA)

The interaction between diethylenetriaminepentaacetic acid (DTPA or H_sZ) and Ce(III) and Th(IV) ions has been investigated spectrophotometrically in aqueous solution at an ionic strength of 0.1 and for various temperatures. It has been found that the Ce(III)-DTPA chelate (1:1) exhibited a characteristic absorption maximum at 297 nm, and the optimum pH range is between 3.4 to 4.4. The absorption of Ce(III)-DTPA chelate is considerably diminished by adding small amounts of Th(IV) ions. This phenomenon was used to evaluate the formation constant of Th(IV)-DTPA chelate (1:1). The formation constants and the thermodynamic properties characterizing the formation of the chelates have been calculated at 25°. The results are as follows:      

Ce∶KNSBN晶体中光扇效应的响应时间特性研究

以单束光入射Ce∶KNSBN晶体,系统研究了不同入射光波长下,Ce∶KNSBN晶体中光扇效应的响应时间随入射光强度及光入射角的变化情况.结果显示,相同的入射光强度及光入射角下,入射光波长较短时,光扇效应到达稳态的时间较短.相同的入射光强度下,随光入射角的增大,响应时间先减小后增大,但不同波长入射光下,最小值对应的光入射角不同,入射光波长为532 nm时,响应时间最小值对应的θ为15°;入射光波长为632.8 nm时,对应的θ为15.5°.同时研究发现,入射光强度逐渐增大的过程中,响应时间在逐渐减小.     

Low temperature synthesis and luminescence investigations of YAG:Ce,Eu nanocomposite powder for warm white light-emitting diode

The preparation of the cerium and europium co-doped YAG materials as well as the study for their synthesis and emitting mechanism of the energy transfer between Ce³⁺ and Eu³⁺ were investigated in the present study. YAG:Ce³⁺, Eu³⁺ powders were synthesized using a high-energy ball milling method in different sintering temperature and atmosphere: air and H₂/N₂. The effects of the synthesis procedure on the crystallinity, morphology, structure, and luminescence spectra were examined by X-ray diffraction, field emission-scanning electron microscopy, and photoluminescence spectroscopy. The europium co-doped YAG:Ce³⁺ phosphors is improved the chromaticity coordinates.     

Promotion of oxidative desulfurization performance of model fuel by 3DOM Ce-doped HPW/TiO2 material

Phosphotungstic acid (HPW) supported on Ce-doped three-dimensional ordered macroporous (3DOM) TiO₂ catalysts are studied in catalytic oxidation desulfurization (ODS) of model oil. The structural and textural of as-synthesized catalysts are characterized by N₂ adsorption, XRD, Raman spectroscopy, SEM-EDS, TEM, FT-IR, XPS, UV–Vis and ICP. These results upheld the existence of periodically arranged macroporous structure of catalyst, with Keggin-type of HPW dispersed homogeneously on TiO₂ matrix. Among these 3DOM Ce-doped HPW/TiO₂ materials, catalyst with 15 wt.% cerium dosage exhibits best ODS performance, which oxidized 99.8% of dibenzothiophene (DBT) into corresponding sulfone within 40 min. The excellent ODS performance of 3DOM Ce-doped HPW/TiO₂ catalyst is related to the common influence of more oxygen vacancies produced by electron transformation between Ce³⁺ and Ce⁴⁺. The chemisorbed oxygen on the surface catalyst will facilitate the selective oxidation of sulfides to sulfones. Moreover, the 3DOM structure of catalyst will further promote the mass transfer of reactants and products on the pore channel. The as-prepared catalyst shows excellent reusability in the ODS system, no obviously decrease in catalytic activity even after 6 runs.