掺溴聚-4-甲基-1-戊烯的合成研究

 液溴与聚-4-甲基-1-戊烯（PMP）的四氯化碳溶液反应，在光照条件下得到溴代PMP，通过红外与元素分析确证了其结构。并通过热重分析对其性能进行了初步的研究。研究发现，在光照条件下溴原子很容易与PMP中叔丁基上的氢原子发生取代反应，得到化学掺杂溴原子的聚合物。该聚合物在150℃以下比较稳定，在150℃以上就会失去HBr。采用此种方法，可得到掺杂均匀的低密度材料。     

5 MA 100 ns重频LTD驱动器设计

设计了用于Z箍缩丝阵实验的重频LTD驱动器, 含6路并联模组, 每组由8个0.8 MA原型模块串联组成, 全真空结构。原型模块采用全新的单路触发和电感隔离技术, 触发难度和重频运行可靠性得到显著优化。利用电路模拟程序对驱动器进行了仿真计算, 结果表明：在初始半径1.2 cm、线质量1 mg/cm的Z箍缩负载上, 驱动器的输出电流峰值可到5.2 MA, 前沿91 ns;负载内爆最大动能78 kJ, 从电容储能至负载动能的转化效率为11.7%。该驱动器预期将获得高达20%~30%的辐射能量效率, 可为Z箍缩物理研究提供高效的实验平台。     

次临界能源堆物理设计进展

聚变-裂变混合能源堆包括聚变中子源和次临界能源堆,主要目标是生产电能。回顾了国内外混合堆的发展历史,给出混合能源堆设计的边界条件和约束条件,说明次临界能源堆以铀锆合金为燃料、水为冷却剂的设计思想。利用输运燃耗耦合程序 MCORGS 计算了混合能源的燃耗,给出了中子有效增殖因数、能量放大倍数和氚增殖比等物理量随时间的变化。通过分析能谱和重要核素随燃耗时间的变化,说明混合能源堆与核燃料增殖、核废料嬗变混合堆的不同特点。论述了混合堆的热工设计并进行了安全分析。对于燃耗数值模拟程序,通过多家对算,保证其计算结果的可信性。针对次临界能源堆的特点,利用贫铀球壳建立了贫铀聚乙烯装置和贫铀LiH装置,并且专门设计加工了天然铀装置,开展铀裂变率、造钚率、产氚率等中子学积分实验,验证了数值模拟的可靠性。     

多层轴向绝缘堆的电压电流测量

为获取初级试验平台(PTS)装置分层真空轴向绝缘堆的电压电流,设计、标定了微分型电容分压器和微分环。探头的频响实验表明：绝缘堆电压、电流探头的频响上限分别为270 MHz和100 MHz。两种探头均采用在线标定方法来确定幅值灵敏度系数。电压探头在标定时应当保留绝缘堆外侧的水介质,以保证探头附近电场分布不发生改变。PTS装置的实验结果表明：当装置外围馈入电流基本均匀时,绝缘堆电压电流测量结果与相关测试结果自洽,与理论值基本符合;当馈入绝缘堆的电流分布不均匀时,不同角向探头测量结果的偏差导致总电流计算结果的误差较大。     

Z箍缩驱动混合堆包层瞬态传热特性

Z箍缩驱动聚变-裂变混合能源堆（Z-FFR）以较长周期（10 s）脉冲式运行,为实现3000 MW的热功率输出,单个脉冲需要产生的能量较大,包层和第一壁在强热冲击下的瞬态传热和温度特性是决定Z-FFR技术可行性的关键问题之一。通过理论计算,分析了在连续脉冲作用下包层和第一壁温度随时间的变化规律。同时以输出恒定的电功率为目标,提出了展平系统输出功率的简便方法,并分析了出口冷却剂温度的波动特性。结果表明材料最高温度均在安全限值内,第一壁表面瞬时高温层厚度约为0.5 mm,系统输出功率波动幅度在-2.84%~+2.05%范围内。     

MAGNETOMECHANICAL BEHAVIORS OF GIANT MAGNETOSTRICTIVE MATERIALS

The Laves phase alloy Tb-Dy-Fe, commercially known as Terfenol-D, exhibits the giant room-temperature magnetostriction at moderate field strength of a few kOe due to its combination of high magnetostriction and low magnetocrystalline anisotropic energy. Thus, this pseudobinary rare earth iron compound has found quite a number of applications such as in magnetomechanical transducers, actuators and adaptive vibration control systems. The simultaneous measurements of magnetostriction and magnetization at various fixed compressive pre-stresses applied in the axial direction for Tb0.3Dy0.7Fe1.95 samples are presented. The results show that the magnetostriction increases with increasing compressive stress until it reaches 1742 ×10^6 under 25 MPa, so does the coercive magnetic field. And the hysteresis loop area for magnetization and magnetostriction also increases with the increment of applied compressive stresses. But the maximum magnetic susceptibility χ（dM/dH） is obtained under zero stress field and the strain derivative dλ/dH increases to the highest amplitude of 0.039×10^-6 A^-1m at a stress level of 5 MPa. In the strain versus magnetization intensity curve, the initial fiat stage mainly consisting of a 180° domain wall motion becomes shorter with increasing stress. It means more initial domains are driven to the transversal direction under the compressive stress before magnetization, which is consistent with the improvement of the magnetostriction.     

洋葱碳基双极板制备及在PEMFCs中的应用

以甲烷为碳源,采用化学气相沉积(CVD)法制备了尺寸均匀(粒径在50～140 nm)的带有金属核心的纳米洋葱碳(CNOs)。通过微波加热对合成的CNOs进行纯化得到纯度为99%的洋葱碳材料,并作为双极板导电填料应用于质子交换膜燃料电池(PEMFCs)电堆。通过CNOs的表征和分析表明,合成的CNOs中内嵌Fe-Ni纳米金属粒子。由接触角测试可知,注塑工艺制备的洋葱碳基双极板的润湿角低于91°,亲水性较商用石墨双极板有所改善,有利于电子的传输。经自呼吸电堆耐久性和功率测试发现,由洋葱碳基双极板组装的电堆在13.2 V下的输出功率达到58 W,比商业石墨双极板电堆输出功率(48 W)提高21%。研究证实洋葱碳基复合材料可以提高PEMFCs电堆的功率密度、效率及寿命。     

自悬浮定向流法制备纳米铜微粒及其结构表征

采用自悬浮定向流法制备金属铜纳米微粒,并用TEM,XRD和AES等分析手段研究了铜纳米微粒的形貌、粒度、结构及其表面氧化层特性。结果表明,在一定的参数条件下采用自悬浮定向流法可制备出单晶纳米铜微粒,并且通过工艺参数的调控可达到对微粒粒度的控制。     

掺杂聚苯乙烯制备研究

讨论了惯性约束聚变研究中采用化学及物理手段在聚苯乙烯（PS）材料掺杂卤素、硅、氘等非金属元素以及铁、铬、钛等金属元素的原理和方法。利用硅烷偶联剂对氧化物表面进行了预处理,采用本体聚合的方式将氧化物掺杂在PS网络之中,简述了它们在ICF中的应用。     

Alternating-current losses in two-layer superconducting cables consisting of second-generation superconductors coated by U-shaped ferromagnetic materials

Alternating-current losses in a two-layer superconducting cable, each layer being composed of 15 closely-spaced rectangular wires made up of second-generation superconductors when the ends of wires are coated by either a non-magnetic or strong ferromagnetic material having a U profile is numerically investigated. Computations are carried out through the finite-element method. The alternating-current losses do not increase significantly if the relative permeability of the coating is increased three orders of magnitude, provided that the current amplitude is less than half of the critical current in a superconducting wire. However, the losses are much higher for ferromagnetic coating if the amplitude of the applied current oscillating at 50 Hz is close to the critical current. The ferromagnetic coating is seen to accumulate the magnetic field lines normally on its surfaces, while the field lines are parallel to the long axes of the wires, leading to more significant flux penetration in the coated regions. This facilitates a uniform low-loss current flow in the uncoated regions of the wires. In contrast, coating with a non-magnetic material gives rise to a considerably smaller current flow in the uncoated regions, whereas the low-loss flow is maintained in the coated regions. Moreover, the current flows in opposite directions in the coated and uncoated regions, where the direction in each region is converse for the two materials.