Co3O4/UiO-66@α-Al2O3陶瓷膜对VOCs废气的分离催化性能

以α-Al₂O₃为支撑层, UiO-66为分离层, Co₃O₄为催化层, 构建了Co₃O₄/UiO-66@α-Al₂O₃陶瓷膜.对其形貌结构进行了表征, 并研究了其对挥发性有机物(VOCs)的分离催化性能. 结果表明, 该陶瓷膜对喷涂行业废气中苯与吡啶两种主要成分体现出良好的分离性, 透过侧的气体中吡啶与苯的摩尔浓度比值可由给料侧的1提高至17; 体系中引入臭氧后, 给料侧苯的浓度明显降低, 其去除率可达到89%. 透过侧的吡啶去除率仅为27%, 得到了较大程度的保留, 剩余的吡啶经收集后可进行单独的深度处理. Co₃O₄/UiO-66@α-Al₂O₃陶瓷膜在对喷涂行业废气中苯成分高效降解的同时, 能够有效解决喷涂行业废气处理过程中氮氧化物的排放问题, 有望成为喷涂行业废气预处理工艺的理想选择.     

真空中铝单丝电爆炸的实验研究

开展了铝单丝在负极性电流脉冲作用下电爆炸特性的研究.利用皮秒激光探针,搭建了阴影、纹影和干涉的光学诊断平台,得到了不镀膜铝丝典型的能量沉积过程,在电压崩溃时刻其沉积能量为2.4 eV/atom.为了增加金属丝内的沉积能量,开展了相同电参数及金属丝尺寸下的镀膜铝丝电爆炸实验,其沉积能量可达到5 eV/atom,实现了在电压崩溃之前铝丝完全气化(完全气化所需能量为4 eV/atom).阴影图像展示了高密度丝核区域的膨胀过程,不镀膜铝丝平均膨胀速度为2.2 km/s,而镀膜铝丝因为沉积能量大,其膨胀速度约为不镀膜铝丝的2.3倍,高密度区域膨胀速度为5 km/s.由于阴影不能反映低密度等离子体的膨胀,开展了平行双丝实验,通过测量自发光辐射,估算了低密度等离子体的膨胀速度.利用条纹相机拍摄了不镀膜铝丝电爆炸过程中自发光区域的图像.纹影图像清晰地展示了不镀膜铝丝在电爆炸过程中形成的核冕结构,而镀膜铝丝电爆炸过程中核冕结构得到了一定程度的抑制.从干涉图像计算了相移,在轴对称假设下对相移进行阿贝尔逆变换,重构了三维的铝原子数密度分布.     

Hybrid process for texturization of diamond wire sawn multicrystalline silicon solar cell

Acid texture is difficult for diamond wire sawn (DWS) multicrystalline silicon (mc‐Si) wafer owing to the inhomogeneous distribution of damage layer on the surface. In this article, metal‐assisted chemical etching (MACE) has been selected for introducing a porous seeding layer to induce acid texturing etching. SEM results show that the oval pit structures coverage get obvious improvement even on the smooth areas. Owing to the further improved light absorption ability by second MACE and nanostructure rebuilding (NSR) process, nanostructured DWS mc‐Si solar cell has exhibited a conversion efficiency of 17.96%, which is 0.45% higher than that of DWS wafer with simple acid texture process. (© 2016 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

The effect of applied negative bias voltage on the structure of Ti-doped a-C:H films deposited by FCVA

Ti-doped hydrogenated diamond-like carbon (DLC) films were deposited on Si(1 0 0) substrates by a filtered cathodic vacuum arc (FCVA) method using Ar and CH₄ as the feedstock. The composition and microstructure of the films were investigated by Raman spectroscopy, X-ray photoelectron spectroscopy and IR spectroscopy. The internal stress was determined by the radius of curvature technique. The influence of the bias voltage on the microstructure of the as-deposited films was investigated. It was found that the graphite-like bonds was dominated in the Ti-doped DLC film deposited at 0 V bias voltage. When bias voltage was increased to −150 V, more diamond-like bond were produced and the sp³ content in film reached the maximum value, after which it decreased and more graphite-like bonds feature produced with further increase of the negative bias voltage. The compressive internal in the Ti-doped DLC films also exhibited a maximum value at −150 V bias voltage. IR results indicated that CH bonded intensity reduced, and H atoms bonded with C atoms were substituted for the Ti atoms as the negative bias voltage increasing. All the composition and microstructure change can be explained by considering the plasma conditions and the effect of negative bias voltage applied to the substrate.     

Rashba效应对量子线中束缚磁极化子性质的影响

采用改进的线性组合算符和幺正变换相结合的方法研究了Rashba效应对抛物量子线中强耦合束缚磁极化子性质的影响.计算了抛物量子线中强耦合束缚磁极化子的有效质量和振动频率,对Rb Cl材料的数值计算结果表明:量子线中强耦合束缚磁极化子的振动频率随受限强度和回旋频率的增加而增大;有效质量与磁极化子的受限强度、回旋频率和电子面密度有关,在Rashba效应影响下有效质量随上述各量的变化曲线都发生了分裂.     

Micro-arc ignition on the oily surface of capacitively-coupled plasma

Micro-arc ignition on the oily surface is investigated in a capacitively-coupled plasma (CCP) system. In this system, micro-arc generation is enhanced by increased level of plasma potential, which is induced by a DC-grounded coil between blocking capacitor and the powered electrode. The images of micro-arcs are captured with very short exposure time of 20 μs using intensified charge-coupled device triggered by a high speed comparator and the focused ground electrode is partially soiled with oil. The micro-arcs are observed only on the oily surface of the electrode. This observation provides that the oily surface of CCP is very weak for micro-arc ignition and micro-arc ignition is supposed to be enhanced by the oil evaporation and the thin oil layer, considering the RF Paschen breakdown of the oil vapor within the sheath and the dielectric breakdown of thin oil layer.     

碳柱热电极的制备及应用

用铅笔芯制作了不同直径的碳柱热电极,表征了碳柱热电极的电化学和温敏等各种性质。结果表明,碳柱热电极在多次加热过程中均表现出对温度变化的快速响应以及良好的热稳定性。将其应用于痕量铅的方波阳极溶出伏安法测定,65℃时灵敏度比常温高,Pb2＋浓度在1~22μg/L呈线性关系,线性回归系数r=0.995 5,检测限0.5μg/L。     

分析测试新成果(238~242)电线塑料护套的傅立叶变换红外光谱分析

采用傅立叶变换红外光谱法对21个5种不同颜色的电线塑料护套样品进行了分析.从红外光谱图中可观察到样品特征峰的峰数、峰位、相对峰面积比均有差异,但可以归纳为两大类.其中同种颜色的不同样品在红外谱图中又反映出了不同的信息,这表明在外观颜色十分相近的情况下,采用此方法能够有效的为刑事案件现场遗留的各种塑料制品提供鉴别与比对.     

一种弹体入水冲击波阴影成像可视化系统及其试验研究

扩大成像视野对于开展充水容器中弹体入水冲击波传播及弥散方面的可视化研究具有重要的实际意义。阴影成像技术适用于大视野实验,且对流场冲击波和扰动的可视化研究具有简单性和通用性,其中直接阴影成像最为简单,但可靠点光源的缺乏是阻碍其发展应用的瓶颈。因此基于国产短弧氙灯管,自制了短弧氙灯点光源,根据阴影成像原理,设计出一种弹体入水冲击波阴影成像可视化系统,详细介绍了其组成和运行原理。利用该系统对高速弹体入水进行了试验研究,获得了弹体入水冲击波的阴影成像和冲击波信号的压力时程曲线,通过阴影成像和冲击波信号相结合分析了弹体入水冲击波的传播特性,并进行了理论验证。结果表明:该弹体入水冲击波阴影成像可视化系统具有可靠性和设计的合理性。弹体高速入水后,初始冲击波的强度最大,随着冲击波的传播,冲击波强度逐渐降低,水中冲击波的传播速度不断降低,球形冲击波的半径逐渐增大。