Integral conditions on the asymptotic stability for the damped linear oscillator with small damping

The equation is considered under the assumption . It is proved that is sufficient for the asymptotic stability of , and is best possible here. This will be a consequence of a general result on the intermittent damping, which means that is controlled only on a sequence of non-overlapping intervals.

     

Glass capillary gas chromatography of amino acid enantiomers

Glass capillaries coated with Chirasil-Val, a chirally functionalised polysiloxane, are capable in principle of resolving all protein amino-acid enantiomers in a single run and within a short analysis time, thus allowing for example the quantitative amino acid determination by enantiomer labelling. The elution characteristics of the individual amino acids however are also dependent upon the chemical nature of the capillary wall surface, and a surface pretreatment is found to be necessary if all protein amino acids are to be analysed. Of the various methods of pretreatment tested, etching of borosilicate glass with gaseous HCl followed by deposition of colloidal silicic acid is considered to be the most suitable.     

Influence of mechanical properties of pectin films on charge density and charge density distribution in pectin macromolecule

The hydration and mechanical properties of citrus pectin films were examined in conditions relevant to those in the plant cell wall. The pectins used for this study varied in the degree of esterification (DE) (high or low) and charge distribution on the backbone (random or block). The hydration of the films was controlled in an osmotic pressure experiment using polyethylene glycol solutions (PEG 20000). Hysteresis tests at constant deformation rate (stress vs deformation) were used for investigating the mechanical behaviour of films. Mechanical and hydration properties of pectin films were examined as a function of charge density, charge density distribution and counterion environment—K⁺, Ca²⁺, Mg²⁺. Swelling decreased with increasing counterion concentration. The effect is stronger in the case of Ca²⁺ and Mg²⁺ for low esterified pectins and therefore crosslinks from divalent ions could be assumed. The crosslink effect is confirmed in mechanical experiments where an increase in the film tensile modulus is observed with increasing counterion concentration. It is shown for the first time that in case of highly concentrated pectin solutions Mg²⁺ cations also act as a crosslinker for pectin macromolecules.     

Effect of surfactants on the stability of thin liquid film flow on a rotating disk

The effect of surfactants on surface instabilities of thin liquid film flow on a rotating disk was studied at different flow rates Q (0.5相似文献   

Sensitive Voltammetric Response of p‐Nitroaniline on Single‐Wall Carbon Nanotube‐Ionic Liquid Gel Modified Glassy Carbon Electrodes

An ionic liquid (i.e., 1‐butyl‐3‐methylimidazolium hexafluorophosphate, BMIMPF₆)‐single‐walled carbon nanotube (SWNT) gel modified glassy carbon electrode (BMIMPF₆‐SWNT/GCE) is fabricated. At it the voltammetric behavior and determination of p‐nitroaniline (PNA) is explored. PNA can exhibit a sensitive cathodic peak at ?0.70 V (vs. SCE) in pH 7.0 phosphate buffer solution on the electrode, resulting from the irreversible reduction of PNA. Under the optimized conditions, the peak current is linear to PNA concentration over the range of 1.0×10^?8–7.0×10^?6 M, and the detection limit is 8.0×10^?9 M. The electrode can be regenerated by successive potential scan in a blank solution for about 5 times and exhibits good reproducibility. Meanwhile, the feasibility to determine other nitroaromatic compounds (NACs) with the modified electrode is also tested. It is found that the NACs studied (i.e., p‐nitroaniline, p‐nitrophenol, o‐nitrophenol, m‐nitrophenol, p‐nitrobenzoic acid, and nitrobenzene) can all cause sensitive cathodic peaks under the conditions, but their peak potentials and peak currents are different to some extent. Their peak currents and concentrations show linear relationships in concentration ranges with about 3 orders of magnitude. The detection limits are 8.0×10^?9 M for p‐nitroaniline, 2.0×10^?9 M for p‐nitrophenol, 5.0×10^?9 M for o‐nitrophenol, 5.0×10^?9 M for m‐nitrophenol, 2.0×10^?8 M for p‐nitrobenzoic acid and 8.0×10^?9 M for nitrobenzene respectively. The BMIMPF₆‐SWNT/GCE is applied to the determination of NACs in lake water.     

Preparation and Characterization of Three-dimensionally Ordered Crystalline Macroporous CeO2

Three-dimensional ordered macroporous (3DOM) materials are of great potential importance in catalysis, selective separation, sensor arrays and communications with optical band gaps1. Many results in the synthesis of 3DOM materials have been reported, such as closed-packed silica spheres or polystyrenes (PS) templating routes for silica2, metal oxides1-6 and metals7. Recently, poly(methyl methacrylate) (PMMA) colloidal crystal templates have been used to prepare 3DOM materials of metals8,…     

Determination of Phenolic Compounds Based on Co‐Immobilization of Methylene Blue and HRP on Multi‐Wall Carbon Nanotubes

This work evaluated an amperometric biosensor based on multi‐wall carbon nanotubes (MWCNT), chemically modified with methylene blue (Met) and horseradish peroxidase (HRP), for detection of phenolic compounds. The dependences of the biosensor response due to the enzyme immobilization procedure, HRP amounts, pH and working potential were investigated. The amperometric response for catechol using the proposed biosensor showed a very wide linear response range (1 to 150 μmol L^?1), good sensitivity (50 nA cm^?2 μmol^?1 L), excellent operational stability (after 300 determinations the response remained at 97%) and very good storage stability (lifetime>3 months). Based on all these characteristics, it is possible to affirm that the material is promising for phenol detection due to its good electrochemical response and enzyme stabilization. The biosensor response for various phenolic compounds was investigated.     

Tying together the ultrastructural modifications of wood fibre induced by pulping processes with the mechanical properties of paper

The composition and ultrastructural arrangement of cell wall polymers in wood fibres have determining influence on the properties of wood derived materials. It is therefore important to improve our understanding of the relationship between fibres organisation, the modifications induced by pulping treatments, and the resulting paper sheet mechanical properties. The different treatments to which fibres are subjected during the manufacturing of pulps and papers induce morphological and micro-structural alterations due to the removal of wall constituents and of microfibrillar elements. The impact of pulping processes on fibres was investigated at the ultrastructural scale of transmission electron microscopy. Particular attention was given to the effects of beating in refiners at various intensities on the ultrastructure of fibres. The most characteristic effects consisted of delaminations, microfibril disorganisation, and even fractures, of varying importance depending on the intensity of the mechanical refining. The consequences of internal alterations and surface modifications of the fibres were examined in relation to the paper sheet mechanical properties. Correlations between the type of alteration observed in the fibres and its possible impact on a given paper mechanical property are suggested. With similar approaches, the effects of drying and recycling were studied.     

An investigation of glasses for capillary chromatography

An investigation was conducted of various glasses, other than soda lime or borosilicate, for use in glass capillary gas chromatography. The work has uncovered some unique chromatographic qualities in the use of potash soda lead and fused silica glasses as materials for making glass capillary columns. The fused silica proved to be an ideal material for capillary column construction, being inherently more inert than glass containing metal oxides. It has been shown that through the use of thin wall capillary tubing of high flexibility many of the mechanical problems associated with glass capillary columns, such as fragility and column straightening, can be avoided.     

Influence of the variable wall thickness of the sample tubes and a quartz Dewar on the EPR signal intensity in a single TE102 and double TE104 rectangular cavity

The response of a single TE₁₀₂ and double TE₁₀₄ rectangular cavity to the insertion of samples contained in tubes with variable wall thickness and a quartz Dewar into the cavity has been analyzed. A direct, indirect, and concurrent (positive or negative) “lens effect” inside the double TE₁₀₄ rectangular cavity is discussed. The experimental dependence of the EPR signal intensity on the wall thickness of the sample tube, δ, for the line-like samples with identical length of the sample material column, L=30 mm, recorded in the microwave cavity showed a directly proportional increase of the relative “lens effect” with the increase of the wall thickness of the tube in the interval, δ∈<0.1 mm, >0.5 mm. The insertion of the variable-temperature double-wall quartz Dewar (home-built, resonant frequency shift, ca. −300 MHz) into the single TE₁₀₂ rectangular cavity showed the same relative “lens effect”, with ca. 1.5-time increase of the EPR signal intensity, for a point-like sample and the line-like samples with material columns of diameter of 1 and 1.3 mm, and wall thickness of the sample tubes, δ∈<0.1 mm, >0.5 mm. The increased effect of the Dewar arises because the active volume of the quartz Dewar tube walls is always much more larger than the active volume of the sample tube wall. In the case of the double TE₁₀₄ rectangular cavity, the insertion of the quartz Dewar: (i) into the same cavity, in which the sample is present, caused a direct “lens effect”, with ca. 1.8-fold increase of the EPR signal intensity; however, (ii) into the complementary cavity, in which the sample is absent, caused an indirect “lens effect”, with ca. 0.6-fold decrease of the EPR signal intensity. With the Dewar and sample in one cavity and a large empty sample tube in the complementary cavity, a concurrent (positive or negative) “lens effect” can be observed. Thus, the possible increase/decrease of the EPR signal intensity depends on the volume ratio of the quartz Dewar tube walls and large sample tube wall inserted into the double TE₁₀₄ rectangular cavity. Each of the above phenomena may be a significant source error in quantitative EPR spectrometry unless the samples to be compared in the quantitative EPR analysis are contained in sample tubes having the same wall thickness and each EPR spectra should be recorded inside an identical quartz Dewar.