肿瘤微波热疗的温度场预示及热损伤研究

本文将热损伤的产生和影响引入到肿瘤的微波热疗中。运用微波能量比吸收率SAR的分布分析了微波在组织中的传输和吸收过程,并对微波热疗过程中的温度场、热损伤分布以及血液灌注率的变化进行了数值模拟。     

Electrochemical characterization of poly(vinylidenefluoride)-zinc triflate gel polymer electrolyte and its application in solid-state zinc batteries

Gel polymer electrolyte (GPE) films comprising of poly(vinylidenefluoride), propylene carbonate, ethylene carbonate and zinc trifluoromethane sulfonate are prepared and characterized. The composition of GPE is optimized to contain minimum liquid components with a maximum specific conductivity of 3.94×10⁻³ S cm⁻¹ at (25±1) °C. A detailed investigation on the properties such as ionic conductivity, transport number, electrochemical stability window, reversibility of Zn/Zn²⁺ couple and Zn/gel electrolyte interfacial stability have been carried out. The ionic conductivity follows a VTF behaviour with an activation energy of about 0.0014 eV. Cationic transport number varies from 0.51 at 25 °C to 0.18 at 70 °C. Several cells have been assembled with GPE as the electrolyte, zinc as the anode, γ-MnO₂ as the cathode and their charge–discharge behaviour followed. Capacity values of 105, 82, 64 and 37 mAh/g of MnO₂ have been achieved at 10, 50, 100 and 200 μA/cm² discharge current densities, respectively. The discharge capacity values are almost constant for about 55 cycles for all values of current densities. Cyclic voltammetric study of MnO₂ electrode in Zn/GPE/MnO₂ cell clearly shows intercalation/deintercalation of Zn²⁺.     

On the role of the interface charge in non-ideal metal–semiconductor contacts

The bias dependent interface charge is considered as the origin of the observed non-ideality in current–voltage and capacitance–voltage characteristics. Using the simplified model for the interface electronic structure based on defects interacting with the continuum of interface states, the microscopic origin of empirical parameters describing the bias dependent interface charge function is investigated. The results show that in non-ideal metal–semiconductor contacts the interface charge function depends on the interface disorder parameter, density of defects, barrier pinning parameter and the effective gap center. The theoretical predictions are tested against several sets of published experimental data on bias dependent ideality factor and excess capacitance in various metal–semicoductor systems.     

遥感器CCD驱动器热设计及其在摄像过程中的温度变化

CCD驱动器是航天成像遥感器摄像过程中的主要热源之一。防止CCD驱动器过热是保证其正常工作的重要方面。介绍了遥感器的工作模式和对CCD驱动器采取的热控制措施。通过热平衡试验,利用回归的方法,对CCD驱动器在摄像过程中的温度变化规律进行了分析,同时对热控制效果进行了评估。CCD驱动器工作时升温速率在0.85℃/min左右,整个摄像过程中最高温度约为26℃,所实施的热控制措施效果理想。     

Investigation of the Li1+xV3O8 electrode–organic electrolyte interface by scanning photoelectron microscopy

To investigate the formation of a solid electrolyte interface (SEI) on the Li_1+xV₃O₈ electrode surface in the thermodynamic stability range of the organic electrolyte, we applied scanning photoelectron microscopy (SPEM) to a pristine electrode and to an electrode after ten cycles. The F K-edge absorption spectrum of the cycled electrode showed that LiF forms on the electrode surface during the lithium insertion–extraction process in the Li_1+xV₃O₈/Li cell. The photoelectron spectrum for the cycled electrode showed intense spectral features corresponding to Li 1s, F 2s, F 2p, and P 2p electron signals, whereas these spectral features were of negligible intensity for the pristine electrode. The above results give strong support for the formation of an SEI that consists of LiF and compounds containing phosphorus during operation of the battery. The SPEM images also revealed that the fluorine distribution on the surface of the cycled electrode was inhomogeneous.     

Theoretical Studies on the Si（001）-SiO2 Interface Structure

1 INTRODUCTION Silicon and its alloy have been widely applied in such fields as electronic industry, high-temperature structural ceramics, etc. In addition, the researches on silicon and its relevant materials greatly promote the rapid development of modern optics and infor- mation technology. Therefore, more and more at- tention is focused on the structure of silicon, oxide of silicon and the interfaces between silicon and metal or nonmetal. As an ideal passive film on the Si surface, S…     

Statistical Analysis of the Effect of Mineral Admixtures on the Strength of the Interfacial Transition Zone

Microscopic evidence indicates that the thickness of the interfacial transition zone (ITZ) between the aggregate and the cement paste is modified when mineral admixtures partially replace portland cement. Unfortunately, there is limited information on the significance of these microscopic modifications to the mechanical properties of the ITZ. This research reports experimental results on the shear and tensile strength of the ITZ as affected by the addition of the following mineral admixtures: silica fume, fly ash, and natural pozzolan. Statistical analysis was used to identify the significant parameters affecting the tensile and shear strength of the ITZ. Experimental results indicate that not only does the incorporation of silica fume and fly ash increase the strength of the ITZ, these mineral admixtures have a greater influence on the strength increase of the ITZ than in the strength increase of the cement paste.     

Macrodefect-Free Materials: Modification of Interfaces in Cement Composites by Polymer Grafting

MDF materials are chemically bonded ceramic materials free of the macrodefects typical of hydraulic cement-based materials. MDF materials arising through reactions of sulfo-aluminate-ferrite belitic (SAFB) clinkers and/or Portland cements (PC) with two types of water-soluble polymer (hydroxy-propylmethyl cellulose {HPMC}, polyphosphate glass {poly-P}) are discussed. Mixes of low energy SAFB clinkers with Portland cement, HPMC and, especially poly-P comprise promising cross-linked compositions additional to the better known MDF materials formed from high alumina cement with polyvinylalcohol/acetate. The principles of co-ordination of P and C atoms (of the polymer) with Al and Fe atoms (originating from the cement) are highlighted from spectroscopic information on next-nearest-neighbour interactions, along with the effects of second co-ordination spheres. Polymers modify the interface through functional bonding/grafting of polymer chains onto the surfaces of cement grains. Both the cross-linked atomic structure and the interface coincide well with the model of functional polymers and represent a new type of atomic-level structure in polymer-modified cements. Interpretation is based on previous magnetic resonance and thermal analysis studies. The compactness of Al(Fe)-O-P cross-links reduces transport through the interfaces, increasing the interfacial interactions and resisting the unfavourable uptake of moisture and carbonation.     

Lanthanum nitrate decomposition by both temperature programmed heating and citrate gel combustion

Thermal decomposition of lanthanum nitrate to lanthanum oxide was carried out by both temperature programmed heating (TPH) and citrate-gel combustion. The temperature programmed heating was carried out under flow of oxidizing (air), neutral (nitrogen) and reducing (25 vol.% hydrogen+argone mixture) gases, and the processes were controlled by simultaneous thermogravimetry and differential thermal analysis. It was shown that hydrogen atmosphere helps to reduce temperatures of all decomposition steps. The results of TPH were utilized to check the nature of residues in the products of lanthanum nitrate-to-oxide conversion performed via citrate-gel combustion technique.     

On‐line Determination of Particle Size Distributions in Flowing Dispersions

Emulsions are of great importance to industry. They are involved in many engineering operations, including chemical reactions, extraction, emulsification and suspension polymerization, etc. However, an important problem for these processes is how to control the size distribution of the dispersed phase. Indeed, off‐line analysis of the emulsion may generate uncertainties due to sampling and dilution of the product, which are likely to change the dispersion state and physico‐chemical properties. In this work, an on‐line optical method is proposed to characterize dispersed media in real flowing conditions. This method is based on the time‐analysis of back‐scattered light fluctuations. The present paper deals with the development of this method and its application to dispersions of alumina in water. The results obtained with the on‐line optical method are compared with those acquired by classical laser light scattering and microscopy.