Standardization of Methods for Characterizing the Surface Geometry of Solids

Since a comprehensive survey published in 1999 [1] much work was done in standardizing measuring methods to characterize the surface geometry of dispersed and/or porous solids and to certify reference materials. The present paper is an extension of a short communication [2]. It gives a survey on existing standards and reports on new drafts and proposals.     

On the role of the interface charge in non-ideal metal–semiconductor contacts

The bias dependent interface charge is considered as the origin of the observed non-ideality in current–voltage and capacitance–voltage characteristics. Using the simplified model for the interface electronic structure based on defects interacting with the continuum of interface states, the microscopic origin of empirical parameters describing the bias dependent interface charge function is investigated. The results show that in non-ideal metal–semiconductor contacts the interface charge function depends on the interface disorder parameter, density of defects, barrier pinning parameter and the effective gap center. The theoretical predictions are tested against several sets of published experimental data on bias dependent ideality factor and excess capacitance in various metal–semicoductor systems.     

Convergence of Computational Methods and Stability of Self-Balanced Stresses under Shrinkage of Spherical Inclusions of a Damageable Material

Some iterative methods for calculating self-balanced stresses under shrinkage of a ball inclusion enclosed in a spherical matrix of a physically nonlinear damageable material. The stability of this system was studied using methods of catastrophe theory. It has been established that the beginning of divergence of the proposed iterative processes coincides with the moment of transition of the system to an unstable position of equilibrium.     

遥感器CCD驱动器热设计及其在摄像过程中的温度变化

CCD驱动器是航天成像遥感器摄像过程中的主要热源之一。防止CCD驱动器过热是保证其正常工作的重要方面。介绍了遥感器的工作模式和对CCD驱动器采取的热控制措施。通过热平衡试验,利用回归的方法,对CCD驱动器在摄像过程中的温度变化规律进行了分析,同时对热控制效果进行了评估。CCD驱动器工作时升温速率在0.85℃/min左右,整个摄像过程中最高温度约为26℃,所实施的热控制措施效果理想。     

三量子位Heisenberg XX 链中杂质对纠缠的影响

研究了有杂质时三量子位Heisenberg-XX链中正常格点之间的热纠缠情况，给出了Concurrence的解析表达式.进一步的讨论发现，杂质对正常格点的热纠缠有着重要的影响，甚至能够改变纠缠在反铁磁区的特性.理论表明，可以通过调节温度和杂质参数来控制纠缠. 关键词： Heisenberg -XX链 热纠缠 杂质格点     

Investigation of the Li1+xV3O8 electrode–organic electrolyte interface by scanning photoelectron microscopy

To investigate the formation of a solid electrolyte interface (SEI) on the Li_1+xV₃O₈ electrode surface in the thermodynamic stability range of the organic electrolyte, we applied scanning photoelectron microscopy (SPEM) to a pristine electrode and to an electrode after ten cycles. The F K-edge absorption spectrum of the cycled electrode showed that LiF forms on the electrode surface during the lithium insertion–extraction process in the Li_1+xV₃O₈/Li cell. The photoelectron spectrum for the cycled electrode showed intense spectral features corresponding to Li 1s, F 2s, F 2p, and P 2p electron signals, whereas these spectral features were of negligible intensity for the pristine electrode. The above results give strong support for the formation of an SEI that consists of LiF and compounds containing phosphorus during operation of the battery. The SPEM images also revealed that the fluorine distribution on the surface of the cycled electrode was inhomogeneous.     

板状激光振荡介质温度场和应力场的数值模拟

以非均匀内热源模型为基础,并考虑材料的导热系数和热膨胀系数的温度相关性,利用有限元方法,对板状激光振荡介质在不同功率和冷却强度下的温度和热应力分布进行了数值模拟及分析。根据计算结果提出了最大有效换热系数的概念,指出换热系数超过最大有效换热系数后,继续强化传热对减小高功率激光器的热效应已无明显效果。以此得出采用常规冷却技术所允许的最大泵浦加热功率。     

Theoretical Studies on the Si（001）-SiO2 Interface Structure

1 INTRODUCTION Silicon and its alloy have been widely applied in such fields as electronic industry, high-temperature structural ceramics, etc. In addition, the researches on silicon and its relevant materials greatly promote the rapid development of modern optics and infor- mation technology. Therefore, more and more at- tention is focused on the structure of silicon, oxide of silicon and the interfaces between silicon and metal or nonmetal. As an ideal passive film on the Si surface, S…     

Statistical Analysis of the Effect of Mineral Admixtures on the Strength of the Interfacial Transition Zone

Microscopic evidence indicates that the thickness of the interfacial transition zone (ITZ) between the aggregate and the cement paste is modified when mineral admixtures partially replace portland cement. Unfortunately, there is limited information on the significance of these microscopic modifications to the mechanical properties of the ITZ. This research reports experimental results on the shear and tensile strength of the ITZ as affected by the addition of the following mineral admixtures: silica fume, fly ash, and natural pozzolan. Statistical analysis was used to identify the significant parameters affecting the tensile and shear strength of the ITZ. Experimental results indicate that not only does the incorporation of silica fume and fly ash increase the strength of the ITZ, these mineral admixtures have a greater influence on the strength increase of the ITZ than in the strength increase of the cement paste.     

Improvement of real time diffraction efficiency of NGD holograms by introducing electron donors

Nongelatin dichromated holographic film(NGD) is a new holographic recordingmaterial.Holograms recorded on this material have better environmental stability, higherdiffraction efficiency and stronger real time effect, etc..An experimental study to ascertainthe influence of two electron donors, namely,N,N-dimethylformamide(DMF) and dimethyl-sulfoxide(DMSO),on the real time diffraction efficiency(RTDE) of NGD holograms is car-ried out.The pressence of electron donors not only improves the sensitivity,but also enhancesthe real time effect greatly.RTDE of above 60% at±1 orders of NGD plane transimissiongrating is achieved by introducing electron donors.