高光效高热稳定性蓝色荧光粉Ca2-ySrySiO4:Ce3+,Li+的组成筛选和发光机理

采用高温固相法合成了一系列Ca_(2-x-y)Sr_(y-x)SiO_4∶x Ce~(3+),x Li~+蓝色固溶体荧光粉。XRD结果表明,所合成的固溶体荧光粉均为单一物相。随着Sr~(2+)成分的增加,Ca_(2-y)Sr_y SiO_4物相从单斜晶系β-Ca_2SiO_4向正交晶系α′-Ca_2SiO_4转变,发射光谱逐渐红移。组成为Ca_(1.75)Sr_(0.25)SiO_4时,荧光粉的发射波长最长(454 nm),Stokes位移最大。基质为Ca_(1.1)Sr_(0.9)SiO_4的晶体结构可诱导掺杂离子Ce~(3+)取代SrO_(10)格位、Li~+取代CaO8格位。优化的荧光粉Ca_(1.05)Sr_(0.85)SiO_4∶0.05Ce~(3+),0.05Li~+(CS_(0.85)SO∶CeLi)在375 nm紫外光激发下,发射445 nm的蓝光,内量子效率(IQE)达到91.18%,200℃时发射强度保持室温发光强度的98.70%。根据晶体结构、晶体场分裂和掺杂离子质心位移等理论,讨论了CS_(0.85)SO∶CeLi综合发光效应最佳的内在原因。     

碳化硅块状气凝胶的制备及应用

碳化硅气凝胶具有高温稳定性、低热膨胀系数、良好的抗热震性以及抗氧化和耐腐蚀等优异的性质,在高温和高腐蚀性环境下的隔热、电磁吸波、过滤和吸附等领域具有较大的应用潜力。然而,块状碳化硅气凝胶的可控制备一直是一项较大的挑战。本文综述了块状碳化硅气凝胶在制备工艺和应用两个方面的研究进展,首先分析总结了各种制备工艺及其优缺点,包括有机/SiO₂复合气凝胶碳热还原法、预陶瓷化聚合物裂解法、化学气相沉积法、高温气相渗硅法和碳化硅纳米线组装法;然后,详细介绍了碳化硅气凝胶在高温隔热和电磁吸波两个领域的应用研究进展;最后,展望了碳化硅气凝胶未来的若干发展方向。     

碳点的性质及其在生物传感器领域的应用

碳点(carbon dots,CDs)作为一种具有优良生物相容性、低毒性和表面功能可调的新型碳基纳米材料,在生物传感领域具有极大的应用潜力.本文对碳点的生物效应、发光性质及其发光机理进行了简述,并根据传感机制的不同,将CDs在生物传感领域的应用分为荧光(fluorescence,FL)传感器、电致发光(electroc...     

Recycling of Primary Lithium Batteries Production Residues

Production waste of primary lithium batteries constitutes a considerable secondary lithium feedstock. Although the recycling of lithium batteries is a widely studied field of research, the metallic residues of non-rechargeable lithium battery production are disposed of as waste without further recycling. The risks of handling metallic Li on a large scale typically prevent the metal from being recycled. A way out of this situation is to handle Li in an aqueous solution, from where it can be isolated as Li₂CO₃. However, the challenge in hydrometallurgical treatment lies in the high energy release during dissolution and generation of H₂. To reduce these process-related risks, the Li sheet metal punching residues underwent oxidative thermal treatment from 300 to 400 °C prior to dissolution in water. Converting Li metal to Li₂O in this initial process step results in an energy release reduction of ∼70 %. The optimal oxidation conditions have been determined by experimental design varying three factors: temperature, Li metal sheet thickness, and residence time. With 96.9±2.6 % almost the entire Li amount is converted to Li₂O, after 2.5 h treatment at 400 °C for a Li sheet thickness of 1.99 mm. Final precipitation with CO₂ yields 85.5±3.0 % Li₂CO₃. Using pure Li sheets, the product Li₂CO₃ is obtained in battery-grade quality (>99.5 %). Non-precipitated Li is recirculated into the process on the stage of dissolving Li₂O, thus avoiding loss of material.     

Influence of Carbon Nanotubes on Phase Composition,Thermal and Post-Heating Behavior of Cementitious Composites

This paper experimentally investigates the influence of carbon nanotubes (CNTs) on phase composition, microstructure deterioration, thermal behavior, and residual mechanical strengths of cementitious composites exposed to elevated temperatures. Cement mortars with small dosages of CNTs, 0.05% and 0.2% by weight of cement, were prepared and then heated at 25 °C, 150 °C, 200 °C, 450 °C, and 600 °C for two hours before being tested. The results show positive impact of the CNTs on the hydration process of cement mortar at room temperature and at higher temperatures up to 200 °C. Decomposition of the hydration products is obvious at 450 °C, whereas sever deterioration in the microstructure occurs at 600 °C. The nano reinforcement and bridging effect of the CNTs are obvious up to 450 °C. Thermal behavior characterization shows that CNTs incorporation enhances the thermal conductivity of the unheated and heat-treated mortar specimens. The decomposition of the hydration products needs more heat in the presence of CNTs. Finally, presence of CNTs significantly enhances the residual compressive and flexural strengths of heated mortar specimens for all studied temperatures.     

离子液体/H_2O_2体系脱硫实验研究

选取四种不同种类离子液体(ILs),1-丁基-3-甲基咪唑溴化物([Bmim]Br)、1-丁基-3-甲基咪唑四氟硼酸盐([Bmim]BF_4)、1-丁基-3-甲基咪唑硫酸氢盐([Bmim]HSO_4)、1-丁基-3-甲基咪唑磷酸二氢盐([Bmim]H_2PO_4)与30%H_2O_2溶液在温和条件下对两种高硫脱灰煤样(LS、QX)进行脱硫实验研究。用化学法测定脱硫前后煤样形态硫含量,并利用傅里叶变换红外光谱(FT-IR)、X射线光电子能谱(XPS)、扫描电子显微镜(SEM)及热重(TG)对脱硫前后的煤样进行表征。结果表明,离子液体的加入使H_2O_2氧化脱硫能力增强,煤中硫铁矿硫和有机硫化物硫被显著脱除;经ILs/H_2O_2体系作用后的煤样中小粒径的颗粒减少,颗粒间的缝隙增大,煤表面的凹坑明显,热重实验结果表明,ILs/H_2O_2体系作用后的煤样相对于原煤热失重增大,部分挥发性物质释放峰温提前。     

A novel intumescent flame retardant imparts high flame retardancy to epoxy resin

Intumescent flame retardant (IFR) has received the considerable attention ascribed to the inherent advantages including non‐halogen, low toxicity, low smoke release and environmentally friendly. In this work, a novel charring agent poly (piperazine phenylaminophosphamide) named as PPTA was successfully synthesized and characterized by Fourier transform infrared spectra (FTIR) and X‐ray photoelectron spectroscopy (XPS). Then, a series of flame‐retardant EP samples were prepared by blending with ammonium polyphosphate (APP) and PPTA. Combustion tests include oxygen Index (LOI), vertical Burning Test (UL‐94) and cone calorimeter testing,these test results showed that PPTA greatly enhances the flame retardancy of EP/APP. According to detailed results, EP containing 10 wt% APP had a LOI value of 30.2%,but had no enhancement on UL‐94 rating. However, after both 7.5 wt% APP and 2.5 wt% PPTA were added, EP‐7 passed UL‐94 V‐0 rating with a LOI value of 33.0%. Moreover, the peak heat release rate (PHRR) and peak of smoke product rate (PSPR) of EP‐7 were greatly decreased. Meanwhile, the flame‐retardant mechanism of EP‐7 was investigated by scanning electron microscopy (SEM), thermogravimetric analysis/infrared spectrometry (TG‐IR) and X‐ray photoelectron spectroscopy (XPS). The corresponding results presented PPTA significantly increased the density of char layer, resulting in the good flame retardancy.     

不同松香改性树脂对农药可分散油悬浮剂物理稳定性的影响

研究了添加松香及其改性氢化松香甘油酯、氢化松香季戊四醇酯、松香改性对特辛基苯酚树脂对以油酸甲酯为介质的12.5%氰霜唑·吡唑醚菌酯可分散油悬浮剂物理稳定性及流变特性的影响。傅里叶变换红外光谱表征结果表明,与松香酸相比,氢化松香甘油酯、氢化松香季戊四醇酯和松香改性对特辛基苯酚树脂的羧基吸收峰消失且出现酯基的特征吸收峰。实验中,随加成烷基醇碳链的延长,软化点升高。且随着树脂的质量分数增加,制剂的粘度提高,物理稳定性也相应提高(析油率降低)。流变结果表明,添加松香改性树脂的可分散油悬浮剂体系呈正触变性,且树脂种类对体系的屈服值影响较大,具体表现为:松香改性对特辛基苯酚>氢化松香季戊四醇酯>氢化松香甘油酯>松香,制剂的物理稳定性也呈现相同的趋势。因此,松香改性树脂具有作为可分散油悬浮剂物理稳定剂的应用潜力。     

生物油蒸馏残渣理化性质及热失重研究

利用傅里叶变换红外光谱仪、激光共焦显微拉曼光谱仪和TGA Q500热分析仪对生物油蒸馏残渣及其在不同温度处理后的热解焦炭理化性质进行表征,并对其热失重特性进行分析。结果表明,生物油蒸馏残渣主要是由脂肪族、芳香族和低聚糖类等有机化合物组成;在氮气氛围下热解主要分为三个阶段:30-145℃为小分子物质挥发析出阶段145-550℃为大分子物质裂解和氧化阶段,550-750℃为焦炭产生阶段;热处理过程中各类物质逐步有序热解析出,同时固体产物石墨化程度随着热处理终止温度的升高而升高。     

基于3-羧基-5-氨基-1，2，4-三唑的Cd（Ⅱ）配合物的合成、晶体结构及催化性能

三唑类含能配合物在含能材料领域受到广泛关注。利用溶液法合成了一例含能配合物[Cd （Hatzc）₂（H₂O）]（LH1）,其中H₂atzc=3-羧基-5-氨基-1,2,4-三唑,并用X射线单晶衍射、元素分析、红外光谱等手段进行表征。单晶结构分析结果表明LH1属于单斜晶系,空间群为P2₁/n,呈一维链状结构,通过氢键相互作用形成三维超分子结构。LH1的爆速（D=10.4 km·s^-1）、爆压（p=55.2 GPa）、爆轰能量（16.51 kJ·g^-1）和密度（2.363 g·cm^-3）均优于大多数含能配合物。撞击感度（>40 J）和摩擦感度（>360 N）表明LH1对撞击和摩擦的敏感性较低。高氯酸铵（AP）的催化热分解结果表明,在LH1的催化作用下,AP的高温分解峰提前38℃,释放的热量在较短的时间增加0.46 kJ·g^-1,说明LH1对AP热分解具有良好的催化效果。