New Electroweak Model Without a Higgs Particle

A new unified electroweak model is proposed in this paper. In this unified electroweak model, Higgsmechanism is not used, so no Higgs particle exists in the model. In order to keep the masses of intermediate gaugebosons non-zero, two sets of gauge fields will be introduced. In order to introduce symmetry breaking and to help tointroduce the masses of all fields, a vacuum potential is needed. Except for those terms concerning Higgs particle, thefundamental dynamical properties of this model are similar to those of the standard model. And in a proper limit, thismodel will approximately return to the standard model. The purpose of this paper is not to say that the Higgs particledoes not exist in Nature, it is only to prove that, without a Higgs particle, we can also set up a unified electroweak modelwhich is consistent with present experiments.     

Strain hardening of polycarbonate in the glassy state: Influence of temperature and molecular weight

This study is concerned with the temperature and molecular weight dependence of the strain-hardening behavior of polycarbonate. It is shown that the strain-hardening modulus reduces with increasing temperature and decreasing molecular weight. This result is interpreted in terms of temperature accelerated relaxation of the entanglement network. Moreover, it is shown that frozen-in orientations, induced by homogeneous deformations above the glass transition temperature, lead to anisotropic yield behavior that can be fully rationalized (and modelled) in terms of a superimposed stress contribution of the prestrained network. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2041–2049, 2004     

Dynamic surface tension measurements of surfactant solutions using the maximum bubble pressure method – limits of applicability

One of the essential differences in the design of bubble pressure tensiometers consists in the geometry of the measuring capillaries. To reach extremely short adsorption times of milliseconds and below, the so-called deadtime of the capillaries must be of the order of some 10 ms. In particular, for concentrated surfactant solutions, such as micellar solutions, short deadtimes are needed to minimize the initial surfactant load of the generated bubbles. A theoretical model is derived and confirmed by experiments performed for a wide range of experimental conditions, mainly in respect to variations in deadtime and bubble volume.     

Comparisons of pharynx, source, formant, and pressure characteristics in operatic and musical theatre singing

Belting, a vocal technique typically cultivated in musical theatre singing, differs timbrally from operatic singing in many interesting respects. The underlying phonatory differences have not been previously investigated in detail. Yet, belting is frequently associated with disturbances of voice function. Articulatory and phonatory characteristics are investigated in a female subject who is a professional singer (co-author JL) trained in both the operatic and belting styles and in an intermediate vocal technique (“mixed”). This article presents data obtained from this subject by video-fiberoptic observation of the pharynx, inverse filtering of airflow, and measurement of subglottal pressure. The results reveal that belting was characterized by very high subglottal pressures and sound levels, and apparently also by a comparatively high degree of glottal adduction. Comparisons with other investigations of related aspects of belting and operatic singing support the assumption that the data obtained from our subject are representative for these vocal techniques.     

Gas solubility of carbon dioxide in poly(lactic acid) at high pressures: Thermal treatment effect

The sorption of carbon dioxide in glassy Poly(lactic acid) (PLA) films was studied by quartz crystal microbalance (QCM) at high pressures. Two thermal treatments, melted and quenched, were performed in PLA with two different L:D contents, 80:20 and 98:2, films and compared with a third thermal protocol, annealed, and used in a previous work. The results obtained show that for pressures higher than 2 MPa, the carbon dioxide solubility is larger in PLA 80:20 than in PLA 98:2, indicating that the L:D plays a dominant role on this property. The thermal treatments only affect the gas solubility in PLA 98:2. Sorption isotherms at temperatures 303, 313, and 323 K, below the glass transition temperature of the polymer, and pressures up to 5 MPa were measured and analyzed with three different models, the dual‐mode sorption model, the Flory–Huggins equation, and a modified dual‐mode sorption model where the Henry's law term was substituted by the Flory–Huggins equation. This last model performs especially well for CO₂ in PLA 80:20, due to the convex upward curvature of the solubility isotherms for that system. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 616–625, 2007     

A generalized Adadorov theory for anisotropic thin-walled beams

This paper presents a generalized Adadorov theory for anisotropic thin—walled beams. The theory takes account of the shear strain of the middle surface, which exerts a significant influence on the anisotropic thin-walled beams. A new approach is established to solve the governing equations, which have the same form for both open and closed section beams. The numerical examples show that the effects of the shear strain cannot be neglected for this class of beams.This work was part of research project supported by the National Natural Science Foundation of China     

Predicting the onset of DNA supercoiling using a non-linear hemitropic elastic rod

Elastic rod models provide a means to interpret single molecule DNA experiments as well as predict DNA behavior under physiological conditions. Here we use an elastic rod model to predict the stability boundary (critical torque vs. applied tension) for single molecule DNA experiments in which the molecule is subjected to applied tension and twist. We discuss the shortcomings of the usual isotropic rod model. We then derive a consistent non-linear material law from the general representation for a hemitropic (chiral) rod. Finally, we present results of a standard bifurcation analysis predicting the stability boundary. We find results from the non-linear hemitropic rod to match the data closely.     

Interfacial dynamics‐based modelling of turbulent cavitating flows,Part‐2: Time‐dependent computations

The interfacial dynamics‐based cavitation model, developed in Part‐1, is further employed for unsteady flow computations. The pressure‐based operator‐splitting algorithm (PISO) is extended to handle the time‐dependent cavitating flows with particular focus on the coupling of the cavitation and turbulence models, and the large density ratio associated with cavitation. Furthermore, the compressibility effect is important for unsteady cavitating flows because in a water–vapour mixture, depending on the composition, the speed of sound inside the cavity can vary by an order of magnitude. The implications of the issue of the speed of the sound are assessed with alternative modelling approaches. Depending on the geometric confinement of the nozzle, compressibility model and cavitation numbers, either auto‐oscillation or quasi‐steady behaviour is observed. The adverse pressure gradient in the closure region is stronger at the maximum cavity size. One can also observe that the mass transfer process contributes to the cavitation dynamics. Compared to the steady flow computations, the velocity and vapour volume fraction distributions within the cavity are noticeably improved with time‐dependent computations. Copyright © 2004 John Wiley & Sons, Ltd.