创业企业中两种企业家资源的协调机制分析

创业企业中存在着两种企业家资源：创业企业家和创业投资家。本对这两种企业家资源的特性进行分析，探讨创业投资契约的控制权安排对企业家成长的作用，认为创业投资是一种企业家生成机制。     

Conformational behavior of nylon 6 in mixed solvents

The intrinsic viscosity [η], Huggins constant (K_H), laser light scattering, UV and IR measurements of Nylon 6 are made in m‐cresol and its mixture with 1,4‐dioxane at 20–60 °C. The intrinsic viscosity, R_g, A₂, (<S>²)^1/2 (calculated from viscosity data), R_H, and UV absorbance initially increase and then decrease with the rise in 1,4‐dioxane contents. The K_H and the transmittance of ? OH group in IR spectra show an opposite trend to that of [η]. The dielectric constant calculated from the refractive index of the solvent (m‐cresol with 1,4‐dioxane) and polymer solution shows a continuous decrease with the amount of 1,4‐dioxane. Activation energy shows a minimum while linear expansion coefficient (α³) maximum with the addition of 1,4‐dioxane. Change in [η], K_H, and other characteristics of the polymer solutions with alterations in solvent composition and temperature are the result of variation in the thermodynamic quality of the solvent, its selective adsorption, hydrogen bonding, and conformational transitions. It has been concluded that the addition of 1,4‐dioxane first enhances the quality of the solvent, encourages hydrogen bonding, and specific adsorption, and then deteriorates, bringing conformational transitions in the polymer molecules. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 534–541, 2005     

CdTe太阳电池的不同背电极和背接触层的特性研究

用Ni替代Au来作为CdTe太阳电池的背电极，比较了Ni,Ni/Au,Au/Ni及Au背电极对电池性能的影响.发现Ni作为背电极和ZnTe/ZnTe:Cu复合层接触，电池的开路电压V_oc略有降低，填充因子FF有增有减，变化幅度不大，但因短路电流I_sc有较大的提高，转换效率η平均增长4％.测试了不同背电极的CdTe太阳电池的暗I-V和C-V特性，对背电极剥离后的样品进行了XPS测试分析.结果表明，Ni扩散到ZnTe/ZnTe:Cu复合层的深度比Au多，且大多呈离子态，与ZnTe/ZnTe:Cu复合层中的富Te离子形成Ni_xTe，提高了掺杂浓度，使电池性能获得改善. 关键词： 金属背电极 复合背接触层 转换效率 CdTe太阳电池     

含氮氟化类金刚石(FN-DLC)薄膜的研究：(Ⅲ)疏水性能分析

不同沉积条件下，在单晶硅基底上沉积了含氮氟化类金刚石(FN-DLC)薄膜，用静滴接触角/表面张力测量仪测量了水与FN-DLC膜表面的接触角.用X射线光电子能谱、Raman光谱和傅里叶变换吸收红外光谱(FTIR)分析了薄膜的组分和结构.用原子力显微镜观测了薄膜的表面形貌.结果表明，FN-DLC薄膜疏水性能主要取决于薄膜表面的化学结构、薄膜表面极化强度的强弱、以及薄膜的表面粗糙度的大小.sp³/sp²的比值减小，CF₂基团含量增加，薄膜粗糙度增加，接触角增大；反之，则接触角减小.在工艺上，沉积温度和功率的减小，气体流量比r(r=CF4/［CF₄+CH₄］)的增加，都会使水的浸润性变差，接触角增大. 关键词： 氟化类金刚石膜 疏水性 接触角     

Dynamic characterization of MEMS diaphragm using time averaged in-line digital holography

In this paper dynamic characterization of a MEMS diaphragm is investigated using lens-less time averaged in-line digital holography. The analysis and capability of the numerically reconstructed amplitude and phase information from in-line time averaged holograms as applied to MEMS vibration are presented. Particularly the effect of mean static state on the phase in time averaged digital holography is explored. A novel double exposure method is also demonstrated using a diverging object wave suitable for dynamic characterization of small size objects. A phase jump in the static deformation fringes in the vibrating regions is observed and described and can be used for precise analysis of vibration mode shape under simultaneous presence of mean static deformation. A simple and robust tool for dynamic optical metrology of MEMS devices and micro-objects using time averaged in-line digital holography is thus proposed.     

Analytical solution to a mode of mixed elastohydrodynamic lubrication with mixed contact regimes: Part II—Considering the contact adhering layer effect in the inlet zone

The present paper presents the researches succeeding the first part of the paper [Y.B. Zhang, Analytical Solution to A Mode of Mixed elastohydrodynamic lubrication with Mixed Contact Regimes: Part I—Without Consideration of Contact Adhering Layer in the Inlet Zone. Journal of Molecular Liquids, 2006, Vol.117, (10.1016/j.molliq.2006.04.006)], which analyzed one mode of mixed elastohydrodynamic lubrication with mixed contact regimes for the relatively heavy load and low rolling speed which make the conventional hydrodynamic lubrication occur in the inlet zone while make the physical adsorbed layer boundary lubrication occur in the Hertzian zone, based on the Newtonian fluid model. The present paper presents analysis to other two modes of mixed EHL with mixed contact regimes for relatively heavy loads, low rolling speeds and Newtonian fluids, where the conventional hydrodynamic lubrication, physical adsorbed layer boundary lubrication and oxidized chemical layer boundary lubrication can simultaneously occur in the inlet zone while the oxidized chemical layer boundary lubrication or the fresh metal-oxidized chemical boundary layer dry contact occur in the Hertzian zone, considering the contact adhering layer effect in the inlet zone. The present analysis is also extended to the first mode of mixed EHL with mixed contact regimes as analyzed in Part I [Y.B. Zhang, Analytical Solution to A Mode of Mixed elastohydrodynamic lubrication with Mixed Contact Regimes: Part I—Without Consideration of Contact Adhering Layer in the Inlet Zone. Journal of Molecular Liquids, 2006, Vol.117, (10.1016/j.molliq.2006.04.006)] when the contact adhering layer effect in the inlet zone is considered. Results of contact pressures, film thicknesses, load partitions in the contact and characteristic rolling speeds for approaching to zero averaged hydrodynamic film thickness in the Hertzian zone are obtained from this analysis respectively as functions of the contact adhering layer thickness in the inlet zone. The results show that the contact adhering layer effect in the inlet zone in the present EHL is reduced with the increase of load; At large loads, this effect may be negligible; At small loads, it may be very significant. The results also show that at low rolling speeds, when the contact adhering layer effect in the inlet zone is considered, the load-carrying capacity of the present EHL contact is increased especially for small loads. This means that at low rolling speeds the contact adhering layer effect in the inlet zone may reduce the elastohydrodynamic lubrication deviation from classical EHL theory predictions especially for small loads.     

AutoCAD在机械设计基础中的应用

本文结合机电专业机械设计基础课程的教学特点，将AutoCAD引入课程的设计教学中。这将有益于该课程教学质量的进一步提高。     

基于文丘里管和涡轮流量计的液液两相流测量

本文研究了运用单相流量计组合进行液液两相流参数测量的方法.该方法首先通过静态混合器将液液两相流混合成为均相流,然后利用文丘里管获得两相流差压,利用涡轮流量计获得两相流总体积流量,最后通过液液两相流测量模型获得液液两相流总体积流量、总质量流量、混合密度以及分相流量.初步实验结果表明该方法是可行的,在总体积流量1～6 m3/h,油含率15%～85%的范围内,可有效地测量液液两相流的总体积流量、总质量流量和两相流混合密度,测量相对误差在5%以内,但液液两相流分相流量测量相对误差较大,仍需进一步研究.     

The causal boundary of product spacetimes

The new formulation of the causal completion of spacetimes suggested in Marolf and Ross (Class Quant Grav 20:4085, 2003), and modified later in Flores (Commun Math Phys 2007), is tested by computing the causal boundary for product spacetimes of a Lorentz interval and a Riemannian manifold. This is particularized for two important families of spacetimes, conformal to the previous ones: (standard) static spacetimes and Generalized Robertson-Walker spacetimes. As consequence, it is shown that this new approach essentially reproduces the structure of the conformal boundary for multiple classical spacetimes: Reissner–Nordström (including Schwarzschild), Anti-de Sitter, Taub and standard cosmological models as de Sitter and Einstein Universe.     

Simulation and experimental research on polymer fiber mode selection polished coupler

Multimode dispersion is the main obstacle for high bandwidth in multimode optical fiber （MMF） communication system. Mode selection is an effective method to oppress multimode dispersion. We propose and investigate a kind of polymer optical fiber polished coupler. Beam propagation method （BPM） is employed to calculate the coupling coefficient of transmission modes in MMF coupler, and an output pattern from coupling branch is obtained. Analysis and experiment show that this coupler can select certain modes by changing polished depth, contact area, and intersection angle of two branches, which means that the device can be employed both as a mode selector and a sensor. In addition, simulation shows that five times bandwidth enhancement may be realized by selecting modes with the polymer fiber polished coupler.