超临界CO2布雷登循环热电联供系统多目标优化

本文研究了以超临界CO₂布雷登循环为原动机的热电联供系统,对系统主要运行参数进行了分析,得到运行参数对于系统热力学性能和经济性能的影响规律。同时,以一次能源利用率和单位输出成本作为目标函数,采用多目标遗传算法对系统进行了优化;在优化结果的基础上,通过TOPSIS法决策出最优解,并与单目标最优解进行对比。结果表明,透平进口温度、透平进口压力和压缩机进口温度的增大有利于系统效率的提高;作为代价,成本也相应增加。在热电比0~4范围内,尽可能增大热电比能够最大程度上降低系统的单位输出成本,提高能源的利用率。     

Dissipative Heating of a Viscoelastic Cylinder under a Load Steadily Moving over Its Surface

The Fourier method is used to find the analytical solutions to two-dimensional quasistatic problems of stationary polyharmonic vibrations and dissipative heating of a linearly viscoelastic cylinder. The influence of the cylinder thickness and the width of the loading area on the thermomechanical state of the cylinder is studied based on numerical data__________Translated from Prikladnaya Mekhanika, Vol. 41, No. 2, pp. 23–32, February 2005.     

微波加热制备空心和锯齿形貌Bi_2Te_3晶体(英文)

Well-crystallized Bi₂Te₃ hollow spheres and nanosaws were prepared by microwave heating. Both the ionic liquid and the microwave heating play important role in the formation of the above nanostructures. Hollow spheres can not be obtained only by electronic stove heating, while the addition of ionic liquid leads to fast preparation of nanosaws structure under microwave heating conditions. The similar experimental results have been observed in the preparation of Bi₂S₃, Sb₂S₃ and Bi₂Se₃ nanostructures.     

Influence of the anode material on the characteristics of an analytical glow discharge cell

The energy transfer to the discharge gas due to various collision processes in the plasma and the heating of the sample are widely known effects in glow discharge (GD) spectroscopy. Despite of the considerable thermal effects and their serious influence on the performance of GD devices, measurements of the discharge gas and sample temperatures are not common at all. The gas temperature depends on the power absorption of the discharge as well as on the temperature of boundaries (sample and anode). In this work the influence of different anode materials in a Grimm-type source on the voltage–current characteristics, crater shapes and GD spectra is investigated. Anodes made of titanium and copper alloys, graphite, and steel with thermal conductivities covering a wide range of values are used. For a fixed voltage and pressure a decrease of the measured current is observed for bad thermal conductive anodes. Cooling of the sample results in an increase of the measured current. Both observations can be explained by changes of the discharge gas temperature. The temperature of the sample is measured from the back side and compared for different anodes. Further, it is found that the choice of the anode material (i) has no significant influence on the crater shape, (ii) results in slightly different sputtering rates and (iii) strong differences of the GD spectra.     

Fast oxidation of secondary alcohols by the bromate-bromide system using cyclic microwave heating in acidic water

We report an improved, gentle, cyclic microwave activation technique for the oxidation of secondary alcohols using nonhazardous hypobromous acid (BrOH) as the reagent in acidic water. Several aliphatic and aromatic secondary alcohols were successfully oxidized to the corresponding ketones using this technique in high yields and with only minor amounts of side products.     

Preparation of magnetic indole-3-acetic acid imprinted polymer beads with 4-vinylpyridine and β-cyclodextrin as binary monomer via microwave heating initiated polymerization and their application to trace analysis of auxins in plant tissues

Auxin is a crucial phytohormone for precise control of growth and development of plants. Due to its low concentration in plant tissues which are rich in interfering substances, the accurate determination of auxins remains a challenge. In this paper, a new strategy for isolation and enrichment of auxins from plant tissues was obtained by the magnetic molecularly imprinted polymer (mag-MIP) beads, which were prepared by microwave heating initiated suspension polymerization using indole-3-acetic acid (IAA) as template. In order to obtain higher selective recognition cavities, an enhanced imprinting method based on binary functional monomers, 4-vinylpyridine (4-VP) and β-cyclodextrin (β-CD), was adopted for IAA imprinting. The morphological and magnetic characteristics of the mag-MIP beads were characterized by scanning electron microscopy, Fourier-transform infrared spectroscopy and vibrating sample magnetometry. A majority of resultant beads were within the size range of 80-150μm. Porous surface morphology and good magnetic property were observed. Furthermore, the mag-MIP beads fabricated with 4-VP and β-CD as binary functional monomers exhibited improved recognition ability to IAA, as compared with the mag-MIP beads prepared with the individual monomer separately. Competitive rebinding experiment results revealed that the mag-MIP beads exhibited a higher specific recognition for the template than the non-imprinted polymer (mag-NIP) beads. An extraction method by mag-MIP beads coupled with high performance liquid chromatography (HPLC) was developed for determination of IAA and indole-3-butyric acid (IBA) in plant tissues. Linear ranges for IAA and IBA were in the range of 7.00-100.0μgL(-1) and 10.0-100.0μgL(-1), and the detection limits were 3.9 and 7.4μgL(-1), respectively. The analytical performance was also estimated by seedlings or immature embryos samples from three different plant tissues, pea, rice and wheat. Recoveries were in the range of 70.1-93.5%. The results show that the present imprinting method is a promising approach for preparation of selective adsorbents for sample preparation of auxin analysis in plant tissues.     

Ion Heating in Dusty Plasma of Noble Gas Mixtures

Ion heating in dusty plasma of noble gas mixtures is studied by the observation of dust particles in stratified glow discharge. The particles and their formations can be used as a “contact‐free” probe of the ion flows. It is shown that under condition of experiments transition of dust particles into crystalline state in pure gases occur at much lower pressures in comparison to the case of gas mixtures. This observation is also supported by the evaluation of “effective” kinetic temperature of dust particles as defined from the velocity distribution function at the same set of discharge parameters. Absolute value of temperature of dust component in the mixture of helium and argon indicates important role of argon ionization process (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Grafting of bifunctional phosphonic and carboxylic acids on Phynox: Impact of induction heating

Phynox, a cobalt-chromium alloy, exhibits interesting mechanical properties making it a valuable material for a number of applications. However, its applications (especially biomedical ones) often require specific surface properties that can be imparted via suitable surface functionalizations. Based on Faraday's law of induction, induction heating is a widely used method to heat metallic substrates directly and contactless. The aim of this work is to compare the influence of induction heating and a conventional heating method on the functionalization of Phynox surfaces with bifunctional (6-phosphonohexanoic and 11-phosphoundecanoic acids) monolayers in order to create a platform for a large variety of post-grafting chemical reactions, e.g. with alcohols and amines, to modify and control the surface properties. In a first part, we assess the influence of the heating method on the interaction between the two terminal moieties of the 6-phosphonohexanoic and 11-phosphoundecanoic acids and the Phynox surface by studying the grafting of n-dodecylphosphonic acid and n-dodecanoic acid separately. The suitability of such bifunctional molecules for post-grafting chemical reactions has then been assessed by studying the post-grafting of a fluorinated alcohol by the Steglich esterification reaction between the carboxylic end of the grafted bifunctional molecules and the alcohol function of the post-grafted molecule. It has been shown that induction heating can lead to a much more selective adsorption of bifunctional molecules on the surface of Phynox, leaving a higher amount of free carboxylic acid functions to react during the second modification step.     

Excimer laser accelerated hydrothermal synthesis of ZnO nanocrystals & their electrical properties

The synthesis of ZnO nanocrystals is reported using a hydrothermal chemical growth technique combined with 248 nm nanosecond excimer laser heating at fluences in the range 0-390 mJ cm⁻². The effect of laser heating in controlling the morphology of the nanocrystals is investigated using optical spectroscopy and electron microscopy characterization. Laser heating is shown to allow control of the crystal morphology from nanoparticles to nanorods as well as to modify the size distributions. The results indicate that not only does the laser accelerate the growth of nanocrystals, but can also produce crystals with a narrow size distribution possibly via photothermal size selection. An initial study of electrical conduction properties of ZnO nanocrystal thin films is also discussed.     

高温及超高温热管的启动特性和传热极限

根据局部高温、高热流加热等特殊场合的需求,设计、加工了钠高温热管及锂超高温热管,并对热管的启动和极限特性进行了研究。高温及超高温热管能够顺利启动,但启动时应注意可能到来的声速传热极限。端部加热启动时,端部附近管体部分会形成一段等效的加热段,可以将工质从启动时的固体状态到全部熔化形成相变传热及流动循环的时间确定为启动时间。热管的传热极限特性表明,超高温热管应工作在更高的温度和更大的热流密度。热管的结构和工艺优化有利于启动和运行。