集中荷载下叠合梁抗剪强度

本文对低叠合面钢筋破简支在合梁二阶段受力的斜截面抗剪性能进行了试验研究，并运用非线性有限元分析和试验实测数据，得出了一个适合于集中荷载下高低叠合面叠合梁的抗剪强度计算公式．     

Interpretation of the polyelectrolyte and antipolyelectrolyte effects of poly(N‐vinylimidazole‐co‐sodium styrenesulfonate) hydrogels

Hydrogels of N‐vinylimidazole (VI) and sodium styrenesulfonate (SSS) were synthesized in aqueous solution by radical crosslinking copolymerization with N,N′‐methylene‐bis(acrylamide) as crosslinker. Swelling in several saline solutions was measured for hydrogel samples synthesized with different comonomer concentrations (C_T = 10, 25, or 40%) and with SSS mole fractions covering a broad range (f_SSS = 0–0.7), while the crosslinker ratio was 2 wt % in all cases. The degree of swelling in aqueous solution with a specific ionic strength (μ), plotted versus the SSS composition of the feed, shows a minimum for any set of samples synthesized with a fixed C_T. The dependence of swelling on μ shows both polyelectrolyte (f_SSS beyond the minimum) and antipolyelectrolyte behaviors (in the low f_SSS limit). It was found that the nonGaussian factor of the crosslinking density and the polymer‐solvent interaction parameter increase with f_SSS for any C_T. Moreover, in the low f_SSS limit, the osmotic swelling pressure is governed not only by the ionic contribution, but also by the polymer‐solvent mixing and, the concentration of mobile counterions inside the gel is not proportional to the net fixed charge but to the addition of cationic and anionic side groups, what discards the formation of ionic pairs. The antipolyelectrolyte effect is interpreted as due to the increasing protonation of VI as μ goes up. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1683–1693, 2007     

具有高机械强度的掺Er~(3 )∶TeO_2-Nb_2O_5玻璃的光谱性质研究

熔制了掺铒碲铌玻璃样品(100-X)TeO2-XNb2O5(X=5,10,15,20mol%),测试了其密度、折射率、转变温度、析晶温度、维氏机械强度、吸收光谱、荧光光谱、荧光寿命等参量。利用Judd-Ofelt和McCumber理论分别计算了铒离子强度参量Ωt(t=2,4,6)和受激发射截面σemi的大小,研究了掺铒碲铌玻璃样品光谱参量对Nb2O5成分的依赖性,并与典型的碲锌钠玻璃(75TeO2-20ZnO-5Na2O)在热学、机械强度、光谱性质和放大品行四个方面进行了比较.     

Variation of interband interaction strength in odd-A nuclei

Bandcrossing in 31 rotational bands of 25 different odd-A nuclei in the rare-earth region has been analysed by using a two-band mixing formalism with a constant band interaction within the framework of the effective decoupling picture. The interband interaction strengthV between the one-quasiparticle band and the three-quasiparticle band exhibits a variation with the neutron number which is not different from the oscillatory behaviour observed in even-even nuclei and does not show signs of any appreciable phase shifting as predicted by theory. However, the overall range of variation ofV is greater than that observed in even-even systems.     

Strength of cylinder joint adhesively bonded by coupling

Summary A method of joining two metal cylindrical shafts with adhesive coupling is proposed. Two cylindrical shafts with the same diameter are connected by bonding through a cylindrical coupling with epoxy resin. The strength of the shaft joint under tensile loading and torsional loading is investigated analytically and experimentally. The stress and strain distributions of the shaft joint is analyzed by the finite element method. The analyzed strain distributions in the joint are compared with experimental values. The joint strength is predicted by applying the strength laws of shafts, coupling, adhesive layer and adhesive interface between shaft and adhesive coupling. The effects of the coupling dimension on the joint strength are examined. It is shown that the adhesive shaft joint can transfer the load by which the cylindrical shafts are plastically deformed.This paper was refined by the author, K. Ikegami, during statying at Technische Universität München under the support of Deutscher Akademischer Austauschdients. The author is grateful to Professor Lippmann of Technische Universität München who is the host professor of the support.     

Carbon–epoxy composites based on fibers coated with nylon 6,6: hygrothermal ageing versus interlaminar shear strength

Carbon fibers were coated in situ with a thin film of polyhexamethylene adipamide by an interfacial polycondensation technique. The modified fibers were used for the preparation of epoxy-based unidirectional composites. Specimens of these materials were immersed in water until equilibrium conditions were attained. The weight gain at equilibrium was determined as a function of the immersion temperature, the fiber volume fraction and the polyamide content deposited on the fibers. Water penetration in specimens made with uncoated carbon fibers increases when the volume fraction decreases. Introduction of the polyamide interlayer initially increases the water absorption, but reduces it at higher immersion temperatures and/or higher polyamide contents. The treated specimens were subjected to the short beam test to determine the interlaminar shear strength (ILSS). The data show that the ILSS decreases with water penetration but increases when the immersion temperature increases from 40 to 70°C. The overall performance encountered is discussed in terms of the possible roles of the polyamide interphase while taking into account mechanisms concerned with matrix plasticization, interphase degradation and residual stress relaxation.     

Towards understanding the increase in strength of thermotropic polyesters with heat treatment

Thermotropic copolyester fibers of oxynaphthoate and oxybenzoate have been subjected to conditions that promote solid-state polymerization as well as annealing. The annealing process causes the crystals to perfect with a simultaneous increase in heat of fusion and melting temperature. Solid-state polymerization, a reaction rate-controlled process, causes the polymer viscosity average molecular weight to increase by chain extension from about 14,000 g/mole to more than 87,000 g/mole with a simultaneous impressive increase in tenacity from about 10 g/d (1.2 GPa) to almost 30 g/d (3.7 GPa). To understand the changes in mechanical properties, we have modeled the fiber structure as short rod-like molecules poorly bonded to a continuous matrix of parallel molecules. Lengthening of the reinforcing molecules facilitates better transfer of load from matrix to molecules, resulting in higher tenacity fibers. © 1994 John Wiley & Sons, Inc.     

高剥离类镁等电子序列的磁偶极M1和电四极E2光谱跃迁理论研究

利用全相对论性多组态Dirac-Fock广义平均能级方法，系统地计算了类镁离子3s3p磁偶极Ml^3P2--^3P1和电四极E2 ^2P2--^3P0(Z=20-103)光谱跃迁的能级间隔、跃迁几率和振子强度。计算中考虑了原子核的有限体积效应，进行了高阶Breit修正和QED修正，所得到的能级间隔和最近的实验数据及理论计算值进行了比较。计算结果表明：高原子序数的高荷电离子的磁偶极矩M1和电四极矩E2跃迁几率和中性原子的电偶极E1的相当，在ICF和MCF高温激光等离子体中，磁偶极矩M1和电四极矩E2跃迁过程不容被忽视。     

Fracture strength of class II slot cavities restored with polymerizable restorative materials

This study compared the fracture strength of Class II slot cavities restored with polymerizable restorative materials. Sixty, caries-free, posterior teeth were divided into five groups of 12 teeth. The Class II slot cavities were prepared. The teeth were restored with two packable composites (Filtek P60, Surefil), a microhybrid composite (Filtek Z250)and two ormocer (Definite, Admira). The restorations were then subjected to fracture resistance tests. The marginal ridges of the restorations were loaded at an angle of 13.5° to the long axis of the tooth in an Universal Testing Machine until failure. Analysis of mean forces indicated that, Filtek P60, Surefil and Filtek Z250 exhibited better performance than Definite and Admira. The tested resin composites differed in their mechanical properties. This study suggested that fracture behavior were highly influenced by the filler system. Overall, Filtek P60, Surefil, Filtek Z250, demonstrated good fracture resistance. Copyright © 2003 John Wiley & Sons, Ltd.     

Micromechanisms and Mechanics of Damage and Fracture in Thin Film/Substrate Systems

The purpose of this paper is to review the mechanisms and available theoretical methods for modeling the strength and failure of thin film/substrate systems